Installation guide Radio tubular motor EWFS type WE ... - Warema

Mode button "M"
Learn button "L"
Store button "S"
Encoding switch
Batteries
L
S
-
AAA
+
2x IEC LR03 AAA
+
AAA
Fig. 4: Remote control (with battery compartment opened)
Note:
What about "waving" The sunblind carries out a series of
defined movements in order to confirm a completed program
procedure. We call this procedure "waving".
Learning end positions (Type WE)
■
■
■
■
■
■
■
Press the mode button "M" (Fig. 4) of the remote control.
The transmit LED begins to flash.
Press the button "A" of the remote control for approx.
2 seconds. This initiates learning of the end positions.
Waving is not carried out!
Move the sunblind to the lower end position. Keep
the button pressed during moving. The movement is
interrupted as soon as it is released. It is possible that
a motor moves in the wrong direction, i.e. upwards,
although you have pressed the "DOWN" button. In
this case use the opposite button in order to move the
sunblind downwards.
When the lower end position has been reached, stop
the movement and press the button "A" of the remote
control for approx. 2 seconds. Waving is not carried out!
Now move the sunblind to the upper end position. Keep
the button pressed during moving. The movement is
interrupted as soon as it is released.
When the upper end position has been reached, stop
the movement and press the button "A" of the remote
control for approx. 2 seconds. The sunblind waves if the
end position has been learned successfully.
In Order to complete the learning process, press the
mode button "M" (Fig. 4) of the remote control, the
transmit LED extinguishes, the end positions and the
direction of rotation have been learned.
Learning end positions (Type WEM/WER)
■
■
■
Press the mode button "M" (Fig. 4) of the remote control.
The transmit LED begins to flash.
Press the button "A" of the remote control for approx.
2 seconds. This initiates learning of the end positions.
Waving is not carried out!
Move the sunblind to the lower end position. Keep the
button pressed during moving. The movement is interrupted
as soon as it is released. It is possible that a drive
moves in the wrong direction, i.e. upwards, although
you have pressed the "DOWN" button. In this case use
the opposite button in order to move the sunblind downwards.
-
■
When the lower end position has been reached, stop the
movement and press the button "A" of the remote control
for approx. 2 seconds. Waving is not carried out!
■ Now move the sunblind upwards and stop it approx. 50
mm before the upper end position is reached. Keep the
button pressed during moving. The movement is interrupted
as soon as it is released.
■
■
Press the button "A" of the remote control for approx.
2 seconds. The sunblind waves if the end position has
been learned successfully.
In Order to complete the learning process, press the
mode button "M" (Fig. 4) of the remote control, the
transmit LED extinguishes, the end positions and the
direction of rotation have been learned.
Safety instructions
Never press the buttons on your remote control if you cannot
see the sunblind!
The range of radio control systems is limited by the statutory
regulations on radio systems and by structures. When
planning the system ensure that the radio reception is sufficient.
This applies in particular if the transmitter and receiver
and positioned in different rooms and the radio signal has
to penetrate walls and ceilings. The control system should
not be installed directly near metallic surfaces (steel girders,
fire doors).
■
Therefore check the function of the receiver before finally
carrying out mounting.
Powerful local transmission systems (for example, baby
intercom or neighboring transmitters) whose transmission
frequencies are identical to that of the control system, can
interfere with the reception.
Group operation and special functions
Manifold special functions are possible in WAREMA EWFS.
Should you wish further information, your specialist dealer
will be pleased to send you the EWFS application brochure.
Maintenance
There are no parts to be maintained within the device.
Liability
The manufacturer can reject the warranty for damage to the
product if the product information given in these instructions
is not observed, if it is used for purposes other than those
specified or if used improperly. Liability for consequent damage
to persons or property is also excluded in this case. Observe
the specifications in the operating instructions of your
sunblind. Liability for damage to the sunblind caused by operation
during icing or icy conditions is also excluded.
2
We reserve the right to carry out improvements
93290630•816827•7804K0•06.12.2004