Hardware Manual - NEC UX5000

More documents

Recommendations

Info

Chapter 4 - Terminals and Optional Equipment 6. Plug a modular line cord from the mod jack to the CN1 connector on the 2PGDAD module. 7. Connect the two-conductor station cable from the CN5 connectors within the 2PGDAD module to the external relay. 8. Follow the feature programming as described in the UX5000 Feature Manual (P/N 0913201). The relay closes when the Door Box/external page zone is called. The maximum applied voltage is 24vDC at .5A for each contact. CCPU PCB CN8 CN9 Page Audio Input Page Control Relays Page Controller Amplifier Page Speaker Cross Connect Block Figure 4-17: CCPU PAGE CONNECTIONS 4 - 28 Chapter 4
Chapter 4 - Terminals and Optional Equipment SECTION 4-9 EXTERNAL RECORDING SYSTEM / EXTERNAL RINGER 4.9.1 External Recording System or External Ringer (Figure 4-18) The 2PGDAD allows for the connection of an external recording system or external ringer. With a customerprovided tape recorder, when an extension user dials the ACI analog port extension number, they can automatically start the recorder and activate the record function. When the user hangs up, the recording stops and the tape recorder turns off. For tape recording, connect the tape recorder AUX input jack to the PGDAD jack. Connect the recorder control leads (if available) to the CTL (control relay) jack. By using Department Calling, you can arrange multiple tape recorders into a pool. When an extension user dials the Department Group pilot number, they reach the first available tape recorder in the pool. The relays in the 2PGDAD module can optionally control customer-provided external ringers (loud bells) and buzzers. When an extension user dials the ACI analog port extension number, the associated PGDAD relay closes and activates the ringer. You could use this capability to control an emergency buzzer for a noisy machine shop floor, for example. In addition, if programmed for ringing, an incoming trunk call can activate the ringer/buzzer. 4.9.2 Installing an External Recording System or External Ringer 1. Connecting to the 2PGDAD Module: Make sure the jumper in the 2PGDAD module for the channel is set correctly. (Refer to Figure 4-4 JUMPER SETTINGS on page 4-5). 2. If a line cord was not previously connected to the 2PGDAD, complete Steps 3-6. Otherwise, skip to Step 7. 3. Install a modular jack for each 2PGDAD module. For each module, run one-pair 24 AWG station cable from the cross-connect block to a modular jack. Ground the unused pair. 4. Terminate the extension leads to GRN/RED of the modular jack. Terminate the unused leads to the jack. 5. Install bridging clips as required. 6. Plug a modular line cord from the mod jack to the CN1 connector on the 2PGDAD module. 7. Connect an RCA jack to the audio output(s) on the back of the 2PGDAD module. 8. The opposite end of this cable is connected to the external recording system or external ringer either directly or by connecting to the cross-connect block where the item is connected. 9. Follow the ACI feature programming as described in the UX5000 Feature Manual (P/N 0913201). Chapter 4 4 - 29
Page 1 and 2:
Empowered by Innovation 1. Installi
Page 3 and 4:
Table of Contents Installing the Ch
Page 5 and 6:
Table of Contents Voice Mail Daught
Page 7 and 8:
Table of Contents Resetting the Sys
Page 9 and 10:
Table of Contents EXTERNAL PAGING .
Page 11 and 12:
Table of Contents Programming the I
Page 13 and 14:
Chapter 1 - Installing the Chassis
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Chapter 2 - Blade Installation and
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Chapter 3 - Installing Extensions a
Page 193 and 194:
Chapter 3 - Installing Extensions a
Page 195 and 196: Chapter 3 - Installing Extensions a
Page 219 and 220: Chapter 4 - Terminals and Optional
Page 245: Chapter 4 - Terminals and Optional
Page 287 and 288: 0893100 - 65 0893100 - 64 Chapter 4
Page 297 and 298:
Chapter 4 - Terminals and Optional
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Chapter 5 - LAN Connection Chapter
Page 311 and 312:
Chapter 5 - LAN Connection 5.1.5 Ga
Page 313 and 314:
Chapter 6 - Specifications and Part
Page 315 and 316:
Page 317 and 318:
Page 319 and 320:
Page 321 and 322:
Page 323 and 324:
Page 325 and 326:
Page 327 and 328:
Page 329 and 330:
Page 331 and 332:
Page 333 and 334:
Page 335 and 336:
Page 337 and 338:
Page 339 and 340:
Page 341 and 342:
Page 343 and 344:
Page 345 and 346:
Page 347 and 348:
Page 349 and 350:
Page 351 and 352:
Page 353 and 354:
Page 355 and 356:
Page 357 and 358:
Page 359 and 360:
Page 361 and 362:
Revisions This list includes only t
Page 363 and 364:
Index Numerics 082U Combination Bla
Page 365 and 366:
Index Environmental Requirements .
Page 367 and 368:
Index Remote System Upgrade . . . .
Page 369 and 370:
NEC Unified Solutions, Inc. 4 Fores
show all

Hardware Manual - NEC UX5000

Create successful ePaper yourself

Delete template?

Save as template?