Linkbelt-LS208H2-Spec - Rawalwasia

More documents

Recommendations

Info

LS–208H OPERATING INSTRUCTIONS GENERAL: 1. Rated lifting capacities in pounds as shown on lift charts pertain to this crane as originally manufactured and normally equipped. Modifications to the crane or use of optional equipment other than that specified can result in a reduction of capacity. 2. Construction equipment can be dangerous if improperly operated or maintained. Operation and maintenance of this crane must be in compliance with the information in the Operator’s, Parts, and Safety Manuals supplied with this crane. If these manuals are missing, order replacements through the distributor. 3. The operator and other personnel associated with this crane shall read and fully understand the latest applicable American National Standards Institute (ANSI) safety standards for cranes. 4. All capacities listed in this book are in compliance with ASME/ANSI B30.5. LIFT CRANE OPERATION: 1. Capacities shown are in pounds and are not more than 75% of the tipping loads with the crane standing level on firm supporting surface. A deduction must be made from these capacities for weight of hook block, hook ball, sling, grapple, etc. When using main hook while jib is attached, reduce capacities by values shown on Capacity Deductions For Lifting Off Main Boom Hook With Jib Installed. When using main hook while 5 foot tip extension is attached, reduce capacities by values shown on Capacity Deductions For Lifting Off Main Boom Hook With 5 foot Tip Extension Installed. See Operator’s Manual for all limitations when raising or lowering attachment. 2. The crane capacities in the shaded areas are based on structural strength. The crane capacities in the non–shaded areas are based on stability. 3. For recommended reeving, parts of line, wire rope type, and wire rope inspection, see Wire Rope Capacity chart, Operator’s Manual, and Parts Manual. Rated lifting capacities are based on correct reeving. Deduction must be made for excessive reeving. Any reeving over minimum required (see Wire Rope Capacity Chart) is considered excessive and must be accounted for when making lifts. Use working range diagram to estimate the extra feet of rope then deduct 1.9 lb. for each extra foot of wire rope before attempting to lift a load. 4. Load ratings in this Crane Rating Manual are based on freely suspended loads and make no allowances for such factors as the effect of ground conditions, and operating speeds. The operator shall therefore reduce load ratings in order to take these conditions into account. 5. Rated lifting capacities do not account for the effects of wind on a suspended load or boom. Lifting capacities should be considered acceptable for wind speeds less than 20 mph and appropriately reduced for wind speeds greater than 20 mph. Extreme caution should be used when lifting heavy loads or loads with large wind sail area under high wind conditions (over 20 mph). 6. The capacities listed in this Crane Rating Manual are for the machine with live mast, with the gantry in the raised position. 7. The least stable rated condition is over the side. 8. Booms should be erected and lowered over the end for maximum stability. See Liftoff Capabilities before erecting or lowering boom. 9. Do not operate at radii and boom lengths where the Crane Rating Manual lists no capacity. Do not use longer booms or jibs than those listed in this Crane Rating Manual. Any of the above can cause a tipping condition, or boom and jib failure. 10. These capacities apply only to the crane as originally manufactured and normally equipped by Link–Belt Construction Equipment Company. FOR OVER END BLOCKED CAPACITIES ONLY 1. These capacities can be lifted over either end with the crane standing level on a firm supporting surface with adequate blocking placed under the tread member sprockets/idlers, to prevent rocking. 2. Do not travel with a load. TRAVELING WITH A LOAD: 1. All 360 Rotation Capacities listed in this Crane Rating Manual are pick and carry capacities. 2. The boom must be pointing straight over one end of the crawler lower. If the load was lifted over the side, swing the load over the end and/or if the load was lifted at a long radius and the load is at or near capacity for that radius, boom up to obtain a greater lifting capacity before beginning travel. 3. Engage the swing lock and apply swing brake. 4. Travel slowly and cautiously on a firm and level–supporting surface. DEFINITIONS: 1. Load Radius: Horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of the vertical hoist line or tackle with load applied. 2. Boom Angle: The angle between the boom base section and horizontal with freely suspended load at the rated radius. 3. Working Area: Area measured in a circular arc about the centerline of rotation as shown on the Working Area Diagram. 4. Freely Suspended Load: Load hanging free with no direct external force applied except by the hoist line. 5. Side Load: Horizontal side force applied to the lifted load either on the ground or in the air.
WIRE ROPE CAPACITY 1” 5/8” Parts of Type Type Type Type Type Line “M” “DB” “RB” “ZB” “WB” 1 29,500 29,500 22,700 * 11,000 13,600 * 2 59,000 59,000 45,500 22,000 27,200 3 88,500 88,500 68,100 33,000 40,800 4 118,000 118,000 90,800 44,000 54,620 5 147,500 147,500 113,500 55,000 68,000 6 177,000 177,000 136,200 66,000 81,600 7 206,500 206,500 158,900 77,000 95,200 8 236,000 236,000 181,600 88,000 108,800 LBCE Type DB RB* ZB WB* M Description Notes Capacities shown are in pounds and working loads must not exceed the ratings on the capacity charts in this Crane Rating Manual. Study Operator’s Manual for wire rope inspection procedures. 6 x 26 (6 x 19 Class) – Warrington Seale – Extra Improved Plow Steel – Preformed – Right Lay – Regular Lay – I.W.R.C. 19 x 19 Rotation Resistant– Extra Extra Improved Plow Steel – Preformed – Right Lay – Regular Lay. Swaged – S.F. = 5:1 36 x 7 Class – Non–Rotating – Extra Improved Plow Steel – Right Lay – Regular Lay – S.F. = 5:1 8 Strand – Regular Lay 6 X 19 Class – Extra Improved Plow Steel – Lang Lay * Use of swivel end with 1 part of line is not recommended. WORKING AREAS 360 LIFTOFF CAPABILITIES Over End / Over Side (Gantry In Raised Position) Counterweight (Side Frames) Maximum Boom Maximum Boom + Jib NO (RETRACTED) NO (EXTENDED) A (RETRACTED) A (EXTENDED) AB (EXTENDED) See Note 4 (ft) (ft) 100 N/A 120 N/A 130 N/A 160 N/A 190 170+60 180+45 See Note 4 1. For maximum stability, booms should be erected or lowered over the end with no load and with the hook block on the ground. 2. Crane on firm and level surface. 3. Gantry pins must be installed with the gantry in the raised position. 4. Liftoff over end only with 170 ft.+ 45 ft., 170 ft. + 60 ft., 180 ft. + 30 ft. and 180 ft. + 45 ft. boom. For 170 ft. + 45 ft., 170 ft. + 60 ft., 180 ft. + 30 ft. or 180 ft. + 45 ft. (side frame extended) with AB counterweight only, adequate blocking must be placed under both tread member sprockets (or idler rollers) at the end that the boom is to be lifted off to prevent rocking. The ramps supplied with the crane are consid– ered to be adequate blocking. Over Side Boom See Note Over Idler End Longitudinal Of Crawler Center Of Rotation Over Drive End Idler Sprocket See Note Drive Sprocket Over Side Note: These Lines Determine The Limiting Position Of Any Load For Operation Within Working Areas Indicated. LS–208H
Page 1 and 2: LS-208H II HYLAB Series Lattice Boo
Page 3 and 4: 5436---0205---H8 1 Technical Data S
Page 5 and 6: 5436---0205---H8 1 Table Of Content
Page 7 and 8: Specifications Lattice Boom Crawler
Page 9 and 10: LS-208H II Transportation Weights -
Page 11 and 12: Revolving Upperstructure Frame All
Page 13 and 14: Revolving Upperstructure (continued
Page 15: Lifting Capacities Hydraulic Lattic
Page 19 and 20: 1. The capacities included in the
Page 21 and 22: CAPACITY DEDUCTIONS FOR LIFTING OFF
Page 23 and 24: B A Load Radius (ft) MAIN BOOM CAPA
Page 25 and 26: This page intentionally left blank
Page 27 and 28: Jib Capacities Hydraulic Lattice Bo
Page 29 and 30: WORKING RANGE DIAGRAM 240’ 230
Page 31 and 32: LS-208H II - w/ 44" x 54" Tube Boom
Page 43 and 44: 5436---0205---H8 1 Technical Data S
Page 45 and 46: 5436---0205---H8 1 Table Of Content
Page 47 and 48: Specifications Lattice Boom Crawler
Page 49 and 50: LS-208H II Transportation Weights -
Page 51 and 52: Revolving Upperstructure Frame All
Page 53 and 54: Revolving Upperstructure (continued
Page 55 and 56: 5436---0205---H8 Link -Belt Constru
Page 57 and 58: 5437---0205---H8 LS---208HII Link-B
Page 59 and 60: 5437---0205---H8 This page intentio
Page 61 and 62: LS-208H II Machine Transport Weight
Page 63 and 64: Attachment Options 40’ - 190’
Page 65 and 66: LS-208H II Load Hoisting Performanc
Page 67 and 68:
Link-Belt Construction Equipment Co
Page 69 and 70:
OPERATING INSTRUCTIONS GENERAL: 1.
Page 71 and 72:
LIVE MAST LIFTING CAPACITIES (WITHO
Page 73 and 74:
WORKING RANGE DIAGRAM Maximum Boom
Page 75 and 76:
B A MAIN BOOM CAPACITIES - 40 FT OP
Page 77 and 78:
B A Load Radius (Ft.) MAIN BOOM CAP
Page 79 and 80:
Link-Belt is a registered trademark
Page 81 and 82:
TUBULAR JIB NOTES FOR ANGLE BOOM 1.
Page 83 and 84:
WORKING RANGE DIAGRAM Maximum Boom
Page 85 and 86:
Boom Length (ft) Jib Length (ft) Ji
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
5437---0205---H8 Link -Belt Constru
Page 101 and 102:
5437---0205---H8 LS---208HII Link-B
Page 103 and 104:
5437---0205---H8 This page intentio
Page 105 and 106:
LS-208H II Machine Transport Weight
Page 107 and 108:
Attachment Options 40’ - 190’
Page 109 and 110:
LS-208H II Load Hoisting Performanc
Page 111 and 112:
The capacity portion of the Technic
show all

Linkbelt-LS208H2-Spec - Rawalwasia

Create successful ePaper yourself

Delete template?

Save as template?