MTCC-01 MINIATURE TEC CONTROLLER - VIGO System SA

MTCC-01-xxx
MINIATURE TEC CONTROLLER
FEATURES
- Compact size
- Low cost
- Easy to use
- High stability
- Adjustable temperature
- Low power consumption
APPLICATIONS
- Temperature control of TE cooled IR detectors
- OEM Applications
SPECIFICATION
Parameter
Units
Typical
value
Temperature stability K ±0.01
Conditions, Remarks
Settling time of the set detector temperature
s
s
60
90
2-stage TEC, T det=230K
3-stage TEC, T det=210K
Power supply voltage V sup
V
V
2.6 to 5.5
4.0 to 5.5
for 2-stage TEC
for 3-stage TEC
Maximum TEC output current I tec
A
A
1.1
0.43
for 2-stage TEC
for 3-stage TEC
Maximum TEC output voltage V tec V 3.6
Dimensions mm 70 x 45 x 19 width x depth x height
Mass g 35
Electrical characteristics @T a=20ºC, V dd=5V
DESCRIPTION
The MTCC-01 miniature TEC controller is designed to control temperature of 2- or 3-stage TE cooled IR detectors.
MTCC-01 can be used with the Integrated Detector / Preamplifier Module MIPxC seriec and SIPxC series. The target
temperature is factory adjusted in range of 205 to 255K.
The TEC controller is paired in the factory with the detector delivered in the IR set.
Swapping controllers may cause malfunction or damage of TEC and detector.
129/133 Poznanska St., 05-850 Ozarow Mazowiecki, Poland; tel. +48 22 733 54 20; fax +48 22 733 54 26; e-mail: info@vigo.com.pl
Please note: the information contained in this document is subject to change without further notification. VIGO System reserves the right to alter the performance and any resulting specifications.VS- 13-10-30MB

EXAMPLE WIRING DIAGRAM
MIPAC, MIPDC,
MVPAC or MVPDC
Integrated Preamplifier
AMP2x4-AMP2x4
Cable
MTCC-01 TEC Controller
J2
J1
MPPS-01
AC Power
Adaptor
110 or 240VAC
50..60Hz
SMA-BNC-1
Cable
to oscilloscope
POWER SUPPLY CONNECTORS
Pin configuration of power connector (J1):
Pin configuration of preamplifier connector (J2):
Pin
number
Symbol
Function
Pin
number
Symbol
Function
1 +V dd TEC controller power supply 1 –V sup Power supply output (–)
2 TGND 1) TEC controller power ground 2 TH2 1) Thermistor input
3 +V sup 2) 3) Power supply input (+) 3 V fan / N.C. Fan supply / open
4 GND 1) 3) Power ground 4 TEC– TEC supply output (–)
5 V fan / N.C. Fan supply / open 5 GND Power ground
6 –V sup 2) 3) Power supply input (–) 6 TH1 1) Thermistor input
1)
TGND and GND should be connected together in power
adapter.
2)
See preamplifier specification for details.
3)
Only for preamplifier module supply, not required for proper
controller operation.
For more details about TEC cooling see IR Detectors Catalog.
WARNING: Do not short TEC- or TEC+ to any other supply or
to GND!
7 +V sup Power supply output (+)
8 TEC+ TEC supply output (+)
1) Thermistor polarity without significance.
129/133 Poznanska St., 05-850 Ozarow Mazowiecki, Poland; tel. +48 22 733 54 20; fax +48 22 733 54 26; e-mail: info@vigo.com.pl
Please note: the information contained in this document is subject to change without further notification. VIGO System reserves the right to alter the performance and any resulting specifications.VS- 13-10-30MB

DIMENSIONS [mm]
xxx
-2TE
-3TE
MTCC – 01 – xxx
Product identifier
two-stage cooler controller
three-stage cooler controller
ACCESSORIES
BNC-SMA AMP 2x4 – AMP 2x4 AMP 1x6- POWER AMP 2x4 - DB9
Signal output cable
TEC & Supply cable for MTCC-01
controller
Power supply cable for
MTCC-01 controller
TEC & Supply cable for
STCC-04 controller
MPPS-01
Linear AC power supply
129/133 Poznanska St., 05-850 Ozarow Mazowiecki, Poland; tel. +48 22 733 54 20; fax +48 22 733 54 26; e-mail: info@vigo.com.pl
Please note: the information contained in this document is subject to change without further notification. VIGO System reserves the right to alter the performance and any resulting specifications.VS- 13-10-30MB