SSC 026 Quick Connect Bro v3 - Spraying Systems Co Sp. z o.o.

Quick-Connect 

Nozzle Systems 

Improve spray system performance; reduce installation and maintenance time 

Experts in Spray Technology 

Spray 

Nozzles 


Control 


Analysis 


Fabrication

New 

ProMax ® QuickJet ® Clip-Eyelet ® 

Nozzle Assembly 

The No. 46500A — ProMax Clip-Eyelet nozzle assembly 

combines a “snap-on” pipe connection with easy-to-install 

and replace patented “winged” spray tips for added versatility 

and a no-slip grip in wet conditions. A swivel-type ball nozzle 

body, with up to 56˚ of adjustability, allows you to quickly 

and accurately change the direction of the spray without 

disturbing the pipe connection. As a result, you can finely 

tune the spray alignment to minimize overspray. 

More clamping force — more inlet options 

Now available in four configurations with double clamp and 

enlarged inlet options, the ProMax Clip-Eyelet nozzle assembly 

offers added power and flexibility to economically 

satisfy your application needs. 

The double clamp nozzle assembly 

has the stability and clamping 

force required to sustain 

spraying pressures up to 150 psi, 

while a larger pipe inlet size of 

21/32" eliminates the need for 

retrofit seals. Both single clamp 

and double clamp nozzle assemblies are 

available with a choice of two inlet sizes for accommodating 

9/16" (14.5 mm) or 21/32" (17 mm) diameter drill holes. 

No tools needed for installation and removal 

Maintenance downtime is dramatically reduced with the 

ProMax Clip-Eyelet nozzle. With a simple quarter turn, tip 

installation and removal can be done by hand, in seconds and 

without tools. Easy tip removal allows quick inspection of the 

orifice and tip seal. Tip installation is effortless with a “snapin” 

feel due to a pawl located on the spray tip. Plus, a built-in 

internal stop ensures that the spray tip always locks into the 

correct position. Spray tips are automatically aligned with a 

10˚ offset to provide proper coverage. A standard TEFLON ® - 

coated VITON ® tip seal provides a positive seal between the 

ball and the tip. Since this seal remains attached to the tip, 

accidental loss or misplacement is prevented. 

ProMax material resists chemical attack 

Constructed of a chemically coupled, glass-reinforced 

engineering grade of polypropylene, the ProMax nozzle 

combines strength and durability for excellent chemical 

resistance. With the ability to perform at liquid temperatures 

to 180°F at 100 psi (82°C at 7 bar), the ProMax material is 

well suited for spraying phosphates, acids, solvents, and 

other caustics, as well as withstanding caking, clogging 

and build-up. ProMax nozzles are ideal for a variety of 

applications such as cleaning, rinsing, coating, and wetting. 

Choose from a variety of spray patterns, 

angles, and capacities 

Providing an unmatched spray tip selection to ensure the right 

pattern for your application, the ProMax Clip-Eyelet nozzle 

accepts ProMax Quick VeeJet ® (flat spray pattern), ProMax 

Quick FullJet ® (full cone spray pattern), and ProMax Quick 

WhirlJet ® (hollow cone spray pattern) spray tips, plus a 

wide variety of conventional nozzles when used with 

the threaded ball. 

The ProMax Quick VeeJet tips have six different angles with 

eight different capacities ranging from 1.0 to 7.0 gpm at 

40 psi (4.6 to 32.0 l/min at 4 bar). 

The ProMax Quick FullJet tips are available with standard 

angles with ten capacities ranging from .19 to 2.9 gpm at 40 

psi (.85 to 12.7 l/min at 4 bar). Also offered are wide-angle 

models with seven capacities ranging from .51 to 2.6 gpm at 

40 psi (2.3 to 11.5 l/min at 4 bar). 

The ProMax Quick WhirlJet tips are available with standard 

angles with capacities ranging from .10 to 3.0 gpm at 40 psi 

(.46 to 13.7 l/min at 4 bar). Wide-angle ProMax WhirlJet tips 

have four capacities ranging from 1.0 to 3.0 gpm at 40 psi 

(4.6 to 13.7 l/min at 4 bar). 

VITON is a registered trademark of DuPont Dow Elastomers. 

TEFLON is a registered trademark of E.I. DuPont de Nemours and Company. 

2

ProMax ® QuickJet ® Clip-Eyelet ® Nozzle Assembly Specifications 

Dimensions & Weights 

46500A 

ProMax ® 

Clip-Eyelet ® 

Assembly No. 

Color 

Coded 

Body 



Cap 

To 

Clamp 

On 

Dimensions 

A B C 

Net 

Weight 

A 

C 

46500A_ _-1-PP Medium Gray Light Gray 1" pipe 

1-3/4" 3-1/2" 1-7/8" 

(44 mm) (89 mm) (48 mm) 

2.7 oz. 

(.08 kg) 

B 

46500A __-1-1/4-PP Medium Gray Light Gray 1-1/4" pipe 

46500A __ -1-1/2-PPB Black Light Gray 1-1/2" pipe 

1-7/8" 3-11/16" 1-7/8" 

(48 mm) (94 mm) (48 mm) 

2" 3-13/16" 1-7/8" 

(51mm) (97 mm) (48 mm) 

2.7 oz. 

(.08 kg) 

3.2 oz. 

(.09 kg) 

46500A __ -2-PPB Black Light Gray 2" pipe 

2-3/8" 4-1/16" 1-15/16" 

(60 mm) (103 mm) (49 mm) 

3.2 oz. 

(.09 kg) 

Based on largest/heaviest version of each type. 

Ordering Info 

PROMAX QUICKJET CLIP-EYELET 

NOZZLE ASSEMBLY AND SPRAY TIP 

ASSEMBLY 

SPRAY TIP 

46500A D L – 1 – PP + QPTA 40 10 

*Clamp Design — (no designation) indicates Single Clamp; D indicates Double Clamp 

**Inlet Dia.— (no designation) indicates 9/16" (14.5 mm) dia.; L indicates 21/32" (17 mm) dia. 

Nozzle *Clamp **Inlet Pipe Material Tip Spray Capacity 

Type Design Dia. Size Code Type Angle Size 

ProMax QuickJet Clip-Eyelet Nozzle Assembly Options 

Body Assemblies 

To fit 9/16" (14.5 mm) or 21/32" 

(17 mm) dia. drilled pipe 

Double Clamp Body 

For pressures to 150 psi (10.3 bar) 

Single Clamp Body 

For pressures to 60 psi (4 bar) 

ProMax Spray Tip 

See pages 9-13 

Threaded Ball for Standard Nozzles 

For nozzles with 1/4" Male Connection 

CP20582-1/4-PPB (NPT) 

CPB20582-1/4-PPB (BSPT) 


CP20582-3/8-PPB (NPT) 


Cap Seal 

CP7717-2/121-EPR 

CP7717-2/121-VI, VITON ® 

Tip Seal 

Provides additional seal between 

tip and body 

CP7717-2/17-VI, VITON 

Retrofit Seal 

For headers with 27/32" (21 mm) 

diameter holes 

CP20580-BU SEAL, BUNA-N 

CP20580-VI SEAL, VITON 

Blank Tip 

QPA PLUG 

3

New 

Clip-Eyelet ® Nozzle Assembly 

Designed to ensure easy installation and minimal maintenance 

downtime, the No. 20570 — Clip-Eyelet nozzle assembly 

simply snaps onto an existing header. The nozzle tip is then 

installed, aligned, and secured by twisting the cap — all by 

hand. The assembly is affixed to the header by a spring grade 

stainless steel clamp which fits a 1", 1-1/4", 1-1/2", or 2" pipe. 

Whether you’re removing the entire assembly or just changing 

a spray tip, you’ll save time with the Clip-Eyelet nozzle 

assembly. All of the assembly’s parts are designed for easy 

handling. They’re clearly marked for quick identification, fit 

snugly into place, align easily, and require minimal attention. 

Double clamp and large inlet options 

The standard Clip-Eyelet nozzle assembly offers greater 

flexibility with the addition of double clamp and larger 

pipe inlet designs. 

The double clamp configuration enables spraying operations 

to sustain pressures up to 150 psi while the larger pipe inlet 

size for 21/32" openings, eliminates the need for retrofit seals. 

Each assembly is available with single or double clamp 

configurations and a choice of two inlet sizes to accommodate 

9/16" (14.5 mm) or 21/32" (17 mm) diameter drill holes. 

Built to withstand high temperature and 

corrosion 

Along with convenience, the Clip-Eyelet nozzle assembly 

offers the consistent spray patterns, even coverage, and 

chemical resistance needed for effective cleaning, coating, 

and rinsing. Manufactured of glass-reinforced polypropylene, 

the nozzle assembly withstands high temperatures and resists 

corrosion. It can operate at liquid temperatures up to 180˚F at 

100 psi (82˚C at 7 bar) in the double clamp design. 

Ball-type spray tips allow precise direction of 

flat or hollow cone spray 

More than 30 different configurations of spray tips are 

available for the Clip-Eyelet nozzle assembly. These ball-type 

flat and hollow cone spray tips allow the 

spray pattern to be directed very 

precisely at the surfaces being 

sprayed. The spray tips feature 

spray angles from 15° to 80° 

with capacities ranging from 

.35 to 12.2 gpm (1.2 to 46 l/min). 

Several additional spray tip options for 

extra versatility 

For added versatility, options include a threaded ball 

that accepts a wide variety of conventional nozzles; a blank 

spray tip which stops the 

flow of liquid; and a 

ProMax ® ball for use 

with ProMax FullJet ® , 

VeeJet ® , and WhirlJet ® 

spray tips. 

4

Clip-Eyelet ® Nozzle Assembly Specifications 


A 

B 



To 

Dimensions 

20570 Clip-Eyelet 

Net 



Clamp 

Assembly No. 

Weight 

Body 

Cap 

On 

A B C 

C 

20570__-1-PP Medium Gray Light Gray 1" pipe 

20570 __-1-1/4-PP Medium Gray Light Gray 1-1/4" pipe 

20570 __ -1-1/2-PPB Black Light Gray 1-1/2" pipe 

20570 __ -2-PPB Black Light Gray 2" pipe 

1-3/4" 2-7/8" 1-7/8" 

(44 mm) (73 mm) (48 mm) 

1-7/8" 3-1/16" 1-7/8" 

(48 mm) (78 mm) (48 mm) 

2" 3-3/16" 1-7/8" 

(51 mm) (81 mm) (48 mm) 

2-3/8" 3-7/16" 1-15/16" 

(60 mm) (87 mm) (49 mm) 

2.7 oz. 

(.08 kg) 

2.7 oz. 

(.08 kg) 

3.2 oz. 

(.09 kg) 

3.2 oz. 

(.09 kg) 


Ordering Info 

CLIP-EYELET NOZZLE 

ASSEMBLY AND SPRAY TIP 

ASSEMBLY SPRAY TIP *Clamp Design — (no designation) indicates Single Clamp; D indicates Double Clamp 

**Inlet Dia. — (no designation) indicates 9/16" (14.5 mm) dia.; L indicates 21/32" (17 mm) dia. 

20570 D L – 1 – PP + CT 50 30 – PP 

Nozzle *Clamp **Inlet Pipe Material Tip Spray Capacity Material 

Type Design Dia. Size Code Type Angle Size Code 

Clip-Eyelet Nozzle Assembly Options 

Body Assemblies 

To fit 9/16" (14.5 mm) or 21/32" 

(17 mm) dia. drilled pipe 

Double Clamp Body 

For pressures to 150 psi (10.3 bar) 

Single Clamp Body 

For pressures to 60 psi (4 bar) 

Ball-Type Spray Tip 

See pages 14 and 15 



CP20582-1/4-PPB (NPT) 



CP20582-3/8-PPB (NPT) 


Cap Seal 

CP7717-2/121-EPR 

CP7717-2/121-VI, VITON ® 

Retrofit Seal 

For headers with 27/32" (21 mm) 

diameter holes 



Blank Tip 

CT PLUG – PP 

5

HP Eyelet Nozzle Assembly 

The No. 38625 — HP Eyelet is the first assembly of its kind 

that can be easily installed and removed by hand. The 

assembly’s hinged body only requires one screw for hand 

tightening to the spray header. The screw may be installed 

from either side of the assembly for easy access. It also 

remains attached to the assembly when loosened to eliminate 

the chance of loss or misplacement. 

The assembly features a square body for excellent stability. 

This helps prevent rotation when the retaining cap is removed 

or tightened. It operates at a maximum pressure of 125 psi 

(8.6 bar) and a maximum temperature of 180°F (82°C) — 

making it a good choice for metal pretreatment, food 

processing, electronics, chemical, and car/truck washing 

applications. 

Built to resist chemical attack 

The hinged body is molded of ProMax ® material, with a 

polyphthalamide cap, that combines strength and durability 

with chemical resistance. Plus, the smooth internal surfaces 

of the assembly resist scale and chemical build-up. The seal 

and O-ring are made of EPDM. A VITON ® seal and O-ring 

are optional. 

Easily retrofitted to existing piping systems 

Available for 1-1/4" or 1-1/2" pipe sizes, the HP Eyelet is 

designed to fit a 9/16" (14.5 mm) diameter predrilled pipe 

opening. The assembly can also be easily retrofitted to an 

existing system. Optional retrofit seals fit existing hole 

diameters of 21/32" (17 mm) or 27/32" (21 mm). For added 

convenience, the screw also accepts standard slotted head 

screwdrivers, #2 and 

#3 Phillips head 

screwdrivers, or 5/32" 

Allen wrenches. 

Choose from a 

variety of 

ball/tip options 

The HP Eyelet accepts four different ball/tip options. 

Included are color-coded ball-type spray tips; a ProMax 

QuickJet ® ball for use with ProMax VeeJet ® , FullJet ® , and 

WhirlJet ® spray tips; a threaded ball for use with threaded 

spray nozzles; and a blank tip which blocks the liquid flow 

in a selected spray zone. 

6

HP Eyelet Nozzle Assembly Specifications 

A 

B 


38625 

C 

D 

Hinged 

Split-Eyelet 

Body Assembly 

38625-1-1/4-PP 

38625-1-1/2-PP 

To 

Clamp 

On 

1-1/4" pipe 

1-1/2" pipe 

A 

B 

Dimensions 

C 

D 

Net 

Weight 

4-3/16" 1-1/4" 3-1/4" 1-3/4" 3.9 oz. 

(106 mm) (32 mm) (83 mm) (44 mm) (.11 kg.) 

4-5/16" 1-11/32" 3-1/2" 1-3/4" 3.9 oz. 

(110 mm) (34 mm) (89 mm) (44 mm) (.11 kg.) 


Ordering Info 

PROMAX HP EYELET NOZZLE 


Ordering Info 

HP EYELET NOZZLE 


ASSEMBLY PROMAX BALL SPRAY TIP 

38625-1-1/4-PP+CP46679-PP+QPTA 25 02 

ASSEMBLY 

SPRAY TIP 

38625 – 1-1/4 – PP + CT 50 30 – PP 

Nozzle Pipe Material Ball Tip Spray Capacity 

Type Size Code No. Type Angle Size 

Nozzle Pipe Material Tip Spray Capacity Material 

Type Size Code Type Angle Size Code 

HP Eyelet Nozzle Assembly Options 

Ball-Type Spray Tip 

See pages 14 and 15 

O-Ring Seal (Cap) 

CP7717-2/121-VI, VITON ® 

ProMax Ball and Spray Tip 

CP46679-PP+Spray Tip 

See pages 9-13 

Retrofit Seals 

For headers with 21/32" (17 mm) diameter holes 



For headers with 27/32" (21 mm) diameter holes 





CP20582 - 1/4 - PPB (NPT) 

CPB20582 - 1/4 - PPB (BSPT) 


CP20582-3/8- PPB (NPT) 

CPB20582-3/8- PPB (BSPT) 

Blank Tip 

QPA PLUG or CT PLUG - PP 

7

Common Application Problems and Possible 

Quick-Connect Nozzle System Solutions 

ProMax ® QuickJet ® Clip-Eyelet ® Nozzle – flat spray 

ProMax QuickJet Clip-Eyelet nozzles with a flat 

spray are used to clean automotive bodies and 

component parts in an electrocoat washer before 

painting. 

ProMax QuickJet Clip-Eyelet Nozzle – full cone spray 

ProMax QuickJet Clip-Eyelet nozzles with a full cone 

spray are used to cool canned tomato products on a 

line-type cooling conveyor. 

Clip-Eyelet Nozzle 

Clip-Eyelet nozzles are used for the pretreatment of 

aluminum channels prior to painting. 

HP Eyelet Nozzle 

HP Eyelet nozzles with ProMax flat spray tips are 

used to clean large, off-road construction equipment 

wheels. 

8

Spray Tips for the ProMax ® Clip-Eyelet ® Nozzle Assembly and ProMax HP Eyelet Nozzle Assembly 

ProMax Quick VeeJet ® Spray Tips Standard Angle 

Flat Spray Specifications 

QPTA_10 

1.0 gpm 

(3.9 l/min) 

QPTA_15 

1.5 gpm 

(5.9 l/min) 

QPTA_20 

2.0 gpm 

(7.9 l/min) 

QPTA_30 

3.0 gpm 

(11.8 l/min) 

QPTA_40 

4.0 gpm 

(15.8 l/min) 

QPTA_50 

5.0 gpm 

(19.7 l/min) 

QPTA_60 

6.0 gpm 

(24 l/min) 

QPTA_70 

7.0 gpm 

(28 l/min) 

Capacities at 40 psi (3 bar). 

Performance Data 

Spray Angle 

at 40 psi 

Capacity 

Size 


Tip 


25° 40° 50° 65° 80° 95° 

• * • • • • • 10 White 

• * • • • • • 15 Gray 

• * • • • • • 20 Black 

• • • • • • 30 Orange 

• • • • • • 40 Green 

• • • • • • 50 Yellow 

• • • • • • 60 Blue 

• • • • • • 70 Red 

*Not recommended below 7 psi. 

Capacity 

(gallons per minute) 

5 10 20 30 40 60 80 100 200 

psi psi psi psi psi psi psi psi psi 

.35 .50 .71 .86 1.0 1.2 1.4 1.6 2.2 

.53 .75 1.1 1.3 1.5 1.8 2.1 2.4 3.4 

.71 1.0 1.4 1.7 2.0 2.5 2.8 3.2 4.5 

1.1 1.5 2.1 2.6 3.0 3.7 4.2 4.7 6.7 

1.4 2.0 2.8 3.5 4.0 4.9 5.7 6.3 8.9 

1.8 2.5 3.5 4.3 5.0 6.1 7.1 7.9 11.2 

2.1 3.0 4.2 5.2 6.0 7.3 8.5 9.5 13.4 

2.5 3.5 4.9 6.1 7.0 8.6 9.9 11.1 15.7 


at 3 bar 

Capacity 

Size 


Tip 


25° 40° 50° 65° 80° 95° 

• * • • • • • 10 White 

• * • • • • • 15 Gray 

•* • • • • • 20 Black 

• • • • • • 30 Orange 

• • • • • • 40 Green 

• • • • • • 50 Yellow 

• • • • • • 60 Blue 

• • • • • • 70 Red 

*Not recommended below 0.5 bar. 

Capacity 

(liters per minute) 

0.3 1 2 3 4 5 6 7 14 

bar bar bar bar bar bar bar bar bar 

1.2 2.3 3.2 3.9 4.6 5.1 5.6 6.0 8.5 

1.9 3.4 4.8 5.9 6.8 7.6 8.4 9.0 12.8 

2.5 4.6 6.5 7.9 9.1 10.2 11.2 12.1 17.1 

3.7 6.8 9.7 11.8 13.7 15.3 16.7 18.1 26 

5.0 9.1 12.9 15.8 18.2 20 22 24 34 

6.2 11.4 16.1 19.7 23 25 28 30 43 

7.5 13.7 19.3 24 27 31 33 36 51 

8.7 16.0 23 28 32 36 39 42 60 

9

Spray Tips for the ProMax ® Clip-Eyelet ® Nozzle Assembly and ProMax HP Eyelet Nozzle Assembly continued 

ProMax Quick FullJet ® Spray Tips Standard Angle 

Full Cone Spray Specifications 

QPHA1 

.19 gpm 

(.74 l/min) 

QPHA1.5 

.29 gpm 

(1.1 l/min) 

QPHA2 

.38 gpm 

(1.5 l/min) 

QPHA3 

.57 gpm 

(2.2 l/min) 

QPHA3.5 

.67 gpm 

(2.6 l/min) 

QPHA5 

.95 gpm 

(3.7 l/min) 

QPHA6.5 

1.3 gpm 

(4.8 l/min) 

QPHA8 

1.5 gpm 

(6.8 l/min) 

QPHA10 

1.9 gpm 

(7.4 l/min) 

QPHA15 

2.9 gpm 

(11.2 l/min) 




Tip 

Number 


Tip 


Orifice 

Dia. 

Nom. 

Max. 

Free 

Passage 

Dia.* 

Capacity 



Angle 

5 7 10 20 30 40 60 80 100 150 7 20 80 

psi psi psi psi psi psi psi psi psi psi psi psi psi 

QPHA1 Brown .035" .025" — — .10 .14 .17 .19 .23 .26 .30 .36 — 58° 53° 

QPHA1.5 White .045" .025" — .13 .15 .21 .25 .29 .35 .40 .44 .53 52° 65° 59° 

QPHA2 Gray .047" .040" .14 .17 .20 .28 .34 .38 .46 .53 .59 .70 43° 50° 46° 

QPHA3 Black .061" .040" .22 .26 .30 .42 .50 .57 .69 .79 .88 1.1 52° 65° 59° 

QPHA3.5 Orange .063" .050" .25 .30 .35 .48 .58 .67 .81 .92 1.0 1.3 43° 50° 46° 

QPHA5 Green .077" .050" .36 .42 .50 .69 .82 .95 1.2 1.3 1.5 1.8 52° 65° 59° 

QPHA6.5 Yellow .089" .063" .47 .55 .65 .89 1.1 1.3 1.5 1.7 1.9 2.3 45° 50° 46° 

QPHA8 Beige .096" .063" .58 .68 .80 1.1 1.3 1.5 1.8 2.1 2.3 2.9 54° 65° 61° 

QPHA10 Blue .113" .063" .73 .85 1.0 1.4 1.7 1.9 2.4 2.7 3.0 3.6 58° 67° 61° 

QPHA15 Red .141" .063" 1.1 1.3 1.5 2.1 2.5 2.9 3.5 4.0 4.4 5.3 80° 85° 80° 


Tip 

Number 


Tip 


Orifice 

Dia. 

Nom. 

mm 

Max. 

Free 

Passage 

Dia.* 

mm 

Capacity 



Angle 

0.5 0.7 1.5 2 3 4 5 6 7 10 0.5 0.7 6 

bar bar bar bar bar bar bar bar bar bar bar bar bar 

QPHA1 Brown .89 .64 — .38 .54 .62 .74 .85 .94 1.0 1.1 1.3 — 58° 53° 

QPHA1.5 White 1.1 .64 .49 .57 .81 .93 1.1 1.3 1.4 1.5 1.7 1.9 52° 65° 59° 

QPHA2 Gray 1.2 1.0 .65 .76 1.1 1.2 1.5 1.7 1.9 2.0 2.2 2.6 43° 50° 46° 

QPHA3 Black 1.5 1.0 .98 1.1 1.6 1.9 2.2 2.5 2.8 3.1 3.3 3.9 52° 65° 59° 

QPHA3.5 Orange 1.6 1.3 1.1 1.3 1.9 2.2 2.6 3.0 3.3 3.6 3.9 4.5 43° 50° 46° 

QPHA5 Green 2.0 1.3 1.6 1.9 2.7 3.1 3.7 4.2 4.7 5.1 5.5 6.5 52° 65° 59° 

QPHA6.5 Yellow 2.3 1.6 2.1 2.5 3.5 4.0 4.8 5.5 6.1 6.7 7.1 8.4 45° 50° 46° 

QPHA8 Beige 2.4 1.6 2.6 3.0 4.3 4.9 6.0 6.8 7.5 8.2 8.8 10.4 54° 65° 61° 

QPHA10 Blue 2.9 1.6 3.3 3.8 5.4 6.2 7.4 8.5 9.4 10.2 11.0 13.0 58° 67° 61° 

QPHA15 Red 3.6 1.6 4.9 5.7 8.1 9.3 11.2 12.7 14.1 15.4 16.5 19.4 80° 85° 80° 

*Foreign matter with maximum diameter as listed can pass through 

nozzle without clogging. 

10


ProMax Quick FullJet ® Spray Tips Wide Angle 

Full Cone Spray Specifications 

QPHA2.8W 

.51 gpm 

(2.0 l/min) 

QPHA4.3W 

.79 gpm 

(3.1 l/min) 

QPHA5.6W 

1.0 gpm 

(4.0 l/min) 

QPHA8W 

1.5 gpm 

(5.8 l/min) 

QPHA10W 

1.8 gpm 

(7.2 l/min) 

QPHA12W 

2.2 gpm 

(8.7 l/min) 

QPHA14W 

2.6 gpm 

(10.1 l/min) 




Tip 

Number 


Tip 


Orifice 

Dia. 

Nom. 

Max. 

Free 

Passage 

Dia.* 

Capacity 



Angle 

5 7 10 15 20 30 40 60 80 5 10 80 

psi psi psi psi psi psi psi psi psi psi psi psi 

QPHA2.8W White .057" .040" — — .28 .33 .38 .45 .51 .61 .70 — 120° 102° 

QPHA4.3W Black .073" .040" — — .43 .51 .58 .70 .79 .95 1.1 — 120° 102° 

QPHA5.6W Orange .086" .040" — .48 .56 .67 .76 .91 1.0 1.2 1.4 — 120° 102° 

QPHA8W Green .098" .050" — .68 .80 .96 1.1 1.3 1.5 1.8 2.0 — 120° 103° 

QPHA10W Yellow .109" .050" .74 .86 1.0 1.2 1.4 1.6 1.8 2.2 2.5 112° 120° 103° 

QPHA12W Blue .129" .050" .89 1.0 1.2 1.4 1.6 1.9 2.2 2.6 3.0 114° 120° 103° 

QPHA14W Red .141" .063" 1.0 1.2 1.4 1.7 1.9 2.3 2.6 3.1 3.5 114° 120° 103° 


Tip 

Number 


Tip 


Orifice 

Dia. 

Nom. 

mm 

Max. 

Free 

Passage 

Dia.* 

mm 

Capacity 



Angle 

0.3 0.5 0.7 1 2 3 4 5 6 0.3 0.7 6 

bar bar bar bar bar bar bar bar bar bar bar bar 

QPHA2.8W White 1.4 1.0 — — 1.1 1.2 1.7 2.0 2.3 2.5 2.7 — 120° 102° 

QPHA4.3W Black 1.9 1.0 — — 1.6 1.9 2.6 3.1 3.5 3.9 4.2 — 120° 102° 

QPHA5.6W Orange 2.2 1.0 — 1.8 2.1 2.5 3.4 4.0 4.6 5.1 5.5 — 120° 102° 

QPHA8W Green 2.5 1.3 — 2.6 3.0 3.6 4.8 5.8 6.6 7.2 7.8 — 120° 103° 

QPHA10W Yellow 2.8 1.3 2.6 3.3 3.8 4.5 6.0 7.2 8.2 9.1 9.8 112° 120° 103° 

QPHA12W Blue 3.3 1.3 3.1 3.9 4.6 5.3 7.3 8.7 9.8 10.9 11.8 114° 120° 103° 

QPHA14W Red 3.6 1.6 3.7 4.6 5.3 6.2 8.5 10.1 11.5 12.7 13.7 114° 120° 103° 

*Foreign matter with maximum diameter as listed can pass through nozzle without clogging. 

11


ProMax Quick WhirlJet ® Spray Tips Standard Angle and 

Wide Angle Hollow Cone Spray Specifications 

QPAA_ 

QPAA_W 

Performance-Data Standard Angle 


Tip 

Number 

Inlet 

Dia. 

Nom. 

Orifice 

Dia. 

Nom. 

Capacity 



Angle 

3 5 7 10 20 30 40 60 80 100 7 20 80 


QPAA0.5 .031" .047" — — — .05 .07 .09 .10 .12 .14 .16 — 58° 69° 

QPAA1 .063" .063" — — — .10 .14 .17 .20 .24 .28 .31 — 64° 76° 

QPAA2 .078" .078" — .14 .17 .20 .28 .35 .40 .49 .57 .63 53° 70° 80° 

QPAA3 .094" .094" — .21 .23 .30 .43 .52 .60 .73 .85 .95 55° 79° 80° 

QPAA5 .141" .109" — .35 .42 .50 .70 .86 1.0 1.2 1.4 1.6 70° 75° 79° 

QPAA8 .172" .141" .44 .57 .67 .80 1.1 1.4 1.6 2.0 2.3 2.5 65° 72° 74° 

QPAA10 .188" .172" .55 .72 .84 1.0 1.4 1.7 2.0 2.4 2.8 3.1 70° 76° 75° 

QPAA15 .199" .203" .82 1.1 1.3 1.5 2.1 2.6 3.0 3.7 4.2 4.7 70° 72° 75° 


Tip 

Number 

Inlet 

Capacity 

Orifice 


Dia. 


Dia. 

Angle 

Nom. 

Nom. 

mm mm 0.2 0.5 1 1.5 2 3 4 5 6 7 0.5 1.5 6 


QPAA0.5 .79 1.2 — .16 .23 .28 .32 .39 .46 .51 .56 .60 — 58° 69° 

QPAA1 1.6 1.6 — .32 .46 .56 .64 .79 .91 1.0 1.1 1.2 — 64° 76° 

QPAA2 2.0 2.0 — .64 .91 1.1 1.3 1.6 1.8 2.0 2.2 2.4 53° 70° 80° 

QPAA3 2.4 2.4 — .97 1.4 1.7 1.9 2.4 2.7 3.1 3.3 3.6 55° 79° 80° 

QPAA5 3.6 2.8 — 1.6 2.3 2.8 3.2 3.9 4.6 5.1 5.6 6.0 70° 75° 79° 

QPAA8 4.4 3.6 1.6 2.6 3.6 4.5 5.2 6.3 7.3 8.2 8.9 9.6 65° 72° 74° 

QPAA10 4.8 4.4 2.0 3.2 4.6 5.6 6.4 7.9 9.1 19.2 11.2 12.1 70° 76° 75° 

QPAA15 6.0 5.2 3.1 4.8 6.8 8.4 9.7 11.8 13.7 15.3 16.7 18.1 70° 72° 75° 

12


ProMax Quick WhirlJet ® Spray Tips Standard Angle and 

Wide Angle Hollow Cone Spray Specifications continued 

Performance Data-Wide Angle 


Tip 

Number 

Inlet 

Dia. 

Nom. 

Orifice 

Dia. 

Nom. 

Capacity 



Angle 

3 5 7 10 20 30 40 60 80 100 7 20 80 


QPAA5W .136" .129" — .35 .42 .50 .70 .86 1.0 1.2 1.4 1.6 125° 112° 98° 

QPAA8W .177" .156" .44 .57 .67 .80 1.1 1.4 1.6 2.0 2.3 2.5 112° 100° 87° 

QPAA10W .196" .177" .55 .72 .84 1.0 1.4 1.7 2.0 2.4 2.8 3.1 111° 97° 89° 

QPAA15W .242" .213" .82 1.1 1.3 1.5 2.1 2.6 3.0 3.7 4.2 4.7 110° 98° 90° 


Tip 

Number 

Inlet 

Dia. 

Nom. 

mm 

Orifice Dia. 

Nom. 

mm 

Capacity 



Angle 

0.2 0.5 1 1.5 2 3 4 5 6 7 0.5 1.5 6 


QPAA5W 3.5 3.3 — 1.6 2.3 2.8 3.2 3.9 4.6 5.1 5.6 6.0 125° 112° 98° 

QPAA8W 4.5 4.0 1.6 2.6 3.6 4.5 5.2 6.3 7.3 8.2 8.9 9.6 112° 100° 87° 

QPAA10W 5.0 4.5 2.0 3.2 4.6 5.6 6.4 7.9 9.1 10.2 11.2 12.1 111° 97° 89° 

QPAA15W 6.1 5.4 3.1 4.8 6.8 8.4 9.7 11.8 13.7 15.3 16.7 18.1 110° 98° 90° 

Quick connect nozzles are mounted on an overhead conveyor system in a five section parts washer. 

13

Spray Tips for the Clip-Eyelet ® Nozzle Assembly and HP Eyelet Nozzle Assembly 

Flat Spray Tips Standard Angle Spray Specifications 

CT_10 

1.0 gpm 

(3.9 l/min) 

CT_20 

2.0 gpm 

(7.9 l/min) 

CT_30 

3.0 gpm 

(11.8 l/min) 

CT_40 

4.0 gpm 

(15.8 l/min) 

CT_50 

5.0 gpm 

(19.7 l/min) 

CT_60 

6.0 gpm 

(24 l/min) 

CT_70 

7.0 gpm 

(28 l/min) 

CT_100 

10.0 gpm 

(39 l/min) 




at 40 psi 

Cap. 

Size 

Tip 


15° 25° 40° 50° 65° 80° 

— — — — CT6510-PP CT8010-PP 10 Beige 

— — CT4020-PP CT5020-PP CT6520-PP — 20 Light Blue 

— CT2530-PP CT4030-PP CT5030-PP CT6530-PP — 30 Orange 

— — CT4040-PP CT5040-PP CT6540-PP CT8040-PP 40 Green 

CT1550-PP — CT4050-PP CT5050-PP CT6550-PP — 50 Yellow 

— CT2560-PP CT4060-PP CT5060-PP CT6560-PP CT8060-PP 60 Blue 

CT1570-PP CT2570-PP CT4070-PP CT5070-PP CT6570-PP CT8070-PP 70 Red 

CT15100-PP CT25100-PP CT40100-PP CT50100-PP CT65100-PP CT80100-PP 100 Brown 

Capacity 


5 7 10 20 30 40 60 

psi psi psi psi psi psi psi 

.35 .42 .50 .71 .86 1.0 1.2 

.71 .84 1.0 1.4 1.7 2.0 2.5 

1.1 1.3 1.5 2.1 2.6 3.0 3.7 

1.4 1.7 2.0 2.8 3.5 4.0 4.9 

1.8 2.1 2.5 3.5 4.3 5.0 6.1 

2.1 2.5 3.0 4.2 5.2 6.0 7.3 

2.5 2.9 3.5 4.9 6.1 7.0 8.6 

3.5 4.2 5.0 7.1 8.6 10.0 12.2 


at 3 bar 

Cap. 

Size 

Tip 


15° 25° 40° 50° 65° 80° 

— — — — CT6510-PP CT8010-PP 10 Beige 

— — CT4020-PP CT5020-PP CT6520-PP — 20 Light Blue 

— CT2530-PP CT4030-PP CT5030-PP CT6530-PP — 30 Orange 

— — CT4040-PP CT5040-PP CT6540-PP CT8040-PP 40 Green 

CT1550-PP — CT4050-PP CT5050-PP CT6550-PP — 50 Yellow 

— CT2560-PP CT4060-PP CT5060-PP CT6560-PP CT8060-PP 60 Blue 

CT1570-PP CT2570-PP CT4070-PP CT5070-PP CT6570-PP CT8070-PP 70 Red 

CT15100-PP CT25100-PP CT40100-PP CT50100-PP CT65100-PP CT80100-PP 100 Brown 

Capacity 


0.3 .7 1 1.5 2 3 4 

bar bar bar bar bar bar bar 

1.2 1.9 2.3 2.8 3.2 3.9 4.6 

2.5 3.8 4.6 5.6 6.5 7.9 9.1 

3.7 5.7 6.8 8.4 9.7 11.8 13.7 

5.0 7.6 9.1 11.2 12.9 15.8 18.2 

6.2 9.5 11.4 14.0 16.1 19.7 23 

7.5 11.4 13.7 16.7 19.3 24 27 

8.7 13.3 16.0 19.5 23 28 32 

12.5 19.1 23 28 32 39 46 

14

Spray Tips for the Clip-Eyelet ® Nozzle Assembly and HP Eyelet Nozzle Assembly continued 

Hollow Cone Spray Tips Standard Angle Spray Specifications 

CA15-30.1 

4.5 gpm 

(17.6 l/min) 

CA25-30.1 

5.4 gpm 

(21.4 l/min) 

CA50-50.1 

9.9 gpm 

(39.2 l/min) 

CA50-50.3 

9.8 gpm 

(38.7 l/min) 



Tip and Vane 

Sub-assembly 

No. 

Capacity 



at 40 psi 

5 10 20 30 40 50 60 7 20 60 

psi psi psi psi psi psi psi psi psi psi 

CA15-30.1-PP 1.6 2.3 3.2 3.9 4.5 5.0 5.4 46° 49° 51° 

CA25-30.1-PP 2.0 2.8 3.9 4.7 5.4 6.1 6.6 45° 47° 50° 

CA50-50.1-PP 3.5 5.0 7.0 8.6 9.9 11.1 12.1 38° 46° 48° 

CA50-50.3-PP 3.5 5.0 7.1 8.5 9.8 10.9 11.9 75° 75° 76° 

Tip and Vane 

Sub-assembly 

No. 

Capacity 



at 3 bar 

0.35 .7 1 1.5 2 3 4 0.5 1.5 4 

bar bar bar bar bar bar bar bar bar bar 

CA15-30.1-PP 6.2 8.8 10.4 12.6 14.5 17.6 20.2 46° 49° 51° 

CA25-30.1-PP 7.5 10.7 12.7 15.4 17.6 21.4 24.6 45° 47° 50° 

CA50-50.1-PP 13.5 19.0 22.7 27.8 32.0 39.2 45.2 38° 46° 48° 

CA50-50.3-PP 13.5 19.0 22.7 27.6 31.8 38.7 44.4 75° 75° 76° 

15

Other helpful resources and 

product information for specifying 

spray nozzles 

Industrial Spray Products Catalog 60B 

Our new 524-page catalog features 

tens of thousands of spray system 

solutions. You’ll find design features, 

performance data, dimensions and 

weights, and ordering information all 

in a readable and easy-to-follow 

format. Request Catalog 60B. 

ProMax ® QuickJet ® Nozzles Bulletin 

This newly revised bulletin highlights 

Spraying Systems Co.’s expanded line 

of ProMax nozzles. The time-saving 

installation and maintenance features 

of this nozzle, including easy-to-install 

and replace spray tips, are described in 

detail. Request Bulletin No. 514. 

WindJet ® Air Knife & WindJet 

Air Knife Drying Packages 

This 20-page bulletin presents 

components and performance data 

on WindJet ® Air Knives and 

completely customizable WindJet 

Air Knife Drying Packages. For 

assembly, the brochure provides 

tables and configuration charts 

differentiated by the horsepower 

size of the blower. Request Bulletin 543. 

Spray System Optimization Handbook 

This 52-page, illustrated handbook is 

packed with tips for improving production 

efficiency through spray nozzle maintenance 

and automation. It details system 

problems, common causes of problems 

and viable solutions. It also includes steps 

on defining performance standards, 

solving spray problems, and setting up 

your own maintenance programs. 

Request Technical Manual No. 410. 

Metal Pre-Treatment Bulletin 

This 12-page bulletin includes information 

on spray nozzles for 

improving finished product quality in 

the surface treatment process. 

Included are applications and specifications 

on many spray nozzles and 

accessories designed for surface 

treatment. Request Bulletin No. 354E. 

Air Control Application 

Performance Guide 

This 28-page catalog is a comprehensive 

guide to improving the 

performance of your air control applications. 

The catalog reviews nozzle 

basics, application solutions, system 

automation and engineering data. It 

covers product information on 

nozzles, manifolds, lances, air guns 

and accessories. Request Catalog 20. 

With more than 60 years of helping customers solve spray problems and experience in over 200 industries, Spraying Systems Co. 

is the world leader in spray technology. Our comprehensive spray solutions incorporate 80,000 spray nozzles, turnkey systems, 

spray research and analysis services, and custom fabrication. All of our products and services are engineered with one goal 

in mind — optimizing your spray system. 

P.O. Box 7900 • Wheaton, Illinois 60189-7900 USA 

Phone 1-800-95-SPRAY • Fax 1-888-95-SPRAY 

Outside the U.S., Phone 1(630) 665-5000 • Fax 1(630) 260-0842 

Visit our Web Site: http://www.spray.com 

Represented by: 

Bulletin No. 513B 

Printed in U.S.A. ©Spraying Systems Co. 2003

SSC 026 Quick Connect Bro v3 - Spraying Systems Co Sp. z o.o.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?