SSC 026 Quick Connect Bro v3 - Spraying Systems Co Sp. z o.o.
SSC 026 Quick Connect Bro v3 - Spraying Systems Co Sp. z o.o.
SSC 026 Quick Connect Bro v3 - Spraying Systems Co Sp. z o.o.
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>Quick</strong>-<strong><strong>Co</strong>nnect</strong><br />
Nozzle <strong>Systems</strong><br />
Improve spray system performance; reduce installation and maintenance time<br />
Experts in <strong>Sp</strong>ray Technology<br />
<strong>Sp</strong>ray<br />
Nozzles<br />
<strong>Sp</strong>ray<br />
<strong>Co</strong>ntrol<br />
<strong>Sp</strong>ray<br />
Analysis<br />
<strong>Sp</strong>ray<br />
Fabrication
New<br />
ProMax ® <strong>Quick</strong>Jet ® Clip-Eyelet ®<br />
Nozzle Assembly<br />
The No. 46500A — ProMax Clip-Eyelet nozzle assembly<br />
combines a “snap-on” pipe connection with easy-to-install<br />
and replace patented “winged” spray tips for added versatility<br />
and a no-slip grip in wet conditions. A swivel-type ball nozzle<br />
body, with up to 56˚ of adjustability, allows you to quickly<br />
and accurately change the direction of the spray without<br />
disturbing the pipe connection. As a result, you can finely<br />
tune the spray alignment to minimize overspray.<br />
More clamping force — more inlet options<br />
Now available in four configurations with double clamp and<br />
enlarged inlet options, the ProMax Clip-Eyelet nozzle assembly<br />
offers added power and flexibility to economically<br />
satisfy your application needs.<br />
The double clamp nozzle assembly<br />
has the stability and clamping<br />
force required to sustain<br />
spraying pressures up to 150 psi,<br />
while a larger pipe inlet size of<br />
21/32" eliminates the need for<br />
retrofit seals. Both single clamp<br />
and double clamp nozzle assemblies are<br />
available with a choice of two inlet sizes for accommodating<br />
9/16" (14.5 mm) or 21/32" (17 mm) diameter drill holes.<br />
No tools needed for installation and removal<br />
Maintenance downtime is dramatically reduced with the<br />
ProMax Clip-Eyelet nozzle. With a simple quarter turn, tip<br />
installation and removal can be done by hand, in seconds and<br />
without tools. Easy tip removal allows quick inspection of the<br />
orifice and tip seal. Tip installation is effortless with a “snapin”<br />
feel due to a pawl located on the spray tip. Plus, a built-in<br />
internal stop ensures that the spray tip always locks into the<br />
correct position. <strong>Sp</strong>ray tips are automatically aligned with a<br />
10˚ offset to provide proper coverage. A standard TEFLON ® -<br />
coated VITON ® tip seal provides a positive seal between the<br />
ball and the tip. Since this seal remains attached to the tip,<br />
accidental loss or misplacement is prevented.<br />
ProMax material resists chemical attack<br />
<strong>Co</strong>nstructed of a chemically coupled, glass-reinforced<br />
engineering grade of polypropylene, the ProMax nozzle<br />
combines strength and durability for excellent chemical<br />
resistance. With the ability to perform at liquid temperatures<br />
to 180°F at 100 psi (82°C at 7 bar), the ProMax material is<br />
well suited for spraying phosphates, acids, solvents, and<br />
other caustics, as well as withstanding caking, clogging<br />
and build-up. ProMax nozzles are ideal for a variety of<br />
applications such as cleaning, rinsing, coating, and wetting.<br />
Choose from a variety of spray patterns,<br />
angles, and capacities<br />
Providing an unmatched spray tip selection to ensure the right<br />
pattern for your application, the ProMax Clip-Eyelet nozzle<br />
accepts ProMax <strong>Quick</strong> VeeJet ® (flat spray pattern), ProMax<br />
<strong>Quick</strong> FullJet ® (full cone spray pattern), and ProMax <strong>Quick</strong><br />
WhirlJet ® (hollow cone spray pattern) spray tips, plus a<br />
wide variety of conventional nozzles when used with<br />
the threaded ball.<br />
The ProMax <strong>Quick</strong> VeeJet tips have six different angles with<br />
eight different capacities ranging from 1.0 to 7.0 gpm at<br />
40 psi (4.6 to 32.0 l/min at 4 bar).<br />
The ProMax <strong>Quick</strong> FullJet tips are available with standard<br />
angles with ten capacities ranging from .19 to 2.9 gpm at 40<br />
psi (.85 to 12.7 l/min at 4 bar). Also offered are wide-angle<br />
models with seven capacities ranging from .51 to 2.6 gpm at<br />
40 psi (2.3 to 11.5 l/min at 4 bar).<br />
The ProMax <strong>Quick</strong> WhirlJet tips are available with standard<br />
angles with capacities ranging from .10 to 3.0 gpm at 40 psi<br />
(.46 to 13.7 l/min at 4 bar). Wide-angle ProMax WhirlJet tips<br />
have four capacities ranging from 1.0 to 3.0 gpm at 40 psi<br />
(4.6 to 13.7 l/min at 4 bar).<br />
VITON is a registered trademark of DuPont Dow Elastomers.<br />
TEFLON is a registered trademark of E.I. DuPont de Nemours and <strong>Co</strong>mpany.<br />
2
ProMax ® <strong>Quick</strong>Jet ® Clip-Eyelet ® Nozzle Assembly <strong>Sp</strong>ecifications<br />
Dimensions & Weights<br />
46500A<br />
ProMax ®<br />
Clip-Eyelet ®<br />
Assembly No.<br />
<strong>Co</strong>lor<br />
<strong>Co</strong>ded<br />
Body<br />
<strong>Co</strong>lor<br />
<strong>Co</strong>ded<br />
Cap<br />
To<br />
Clamp<br />
On<br />
Dimensions<br />
A B C<br />
Net<br />
Weight<br />
A<br />
C<br />
46500A_ _-1-PP Medium Gray Light Gray 1" pipe<br />
1-3/4" 3-1/2" 1-7/8"<br />
(44 mm) (89 mm) (48 mm)<br />
2.7 oz.<br />
(.08 kg)<br />
B<br />
46500A __-1-1/4-PP Medium Gray Light Gray 1-1/4" pipe<br />
46500A __ -1-1/2-PPB Black Light Gray 1-1/2" pipe<br />
1-7/8" 3-11/16" 1-7/8"<br />
(48 mm) (94 mm) (48 mm)<br />
2" 3-13/16" 1-7/8"<br />
(51mm) (97 mm) (48 mm)<br />
2.7 oz.<br />
(.08 kg)<br />
3.2 oz.<br />
(.09 kg)<br />
46500A __ -2-PPB Black Light Gray 2" pipe<br />
2-3/8" 4-1/16" 1-15/16"<br />
(60 mm) (103 mm) (49 mm)<br />
3.2 oz.<br />
(.09 kg)<br />
Based on largest/heaviest version of each type.<br />
Ordering Info<br />
PROMAX QUICKJET CLIP-EYELET<br />
NOZZLE ASSEMBLY AND SPRAY TIP<br />
ASSEMBLY<br />
SPRAY TIP<br />
46500A D L – 1 – PP + QPTA 40 10<br />
*Clamp Design — (no designation) indicates Single Clamp; D indicates Double Clamp<br />
**Inlet Dia.— (no designation) indicates 9/16" (14.5 mm) dia.; L indicates 21/32" (17 mm) dia.<br />
Nozzle *Clamp **Inlet Pipe Material Tip <strong>Sp</strong>ray Capacity<br />
Type Design Dia. Size <strong>Co</strong>de Type Angle Size<br />
ProMax <strong>Quick</strong>Jet Clip-Eyelet Nozzle Assembly Options<br />
Body Assemblies<br />
To fit 9/16" (14.5 mm) or 21/32"<br />
(17 mm) dia. drilled pipe<br />
Double Clamp Body<br />
For pressures to 150 psi (10.3 bar)<br />
Single Clamp Body<br />
For pressures to 60 psi (4 bar)<br />
ProMax <strong>Sp</strong>ray Tip<br />
See pages 9-13<br />
Threaded Ball for Standard Nozzles<br />
For nozzles with 1/4" Male <strong><strong>Co</strong>nnect</strong>ion<br />
CP20582-1/4-PPB (NPT)<br />
CPB20582-1/4-PPB (BSPT)<br />
For nozzles with 3/8" Male <strong><strong>Co</strong>nnect</strong>ion<br />
CP20582-3/8-PPB (NPT)<br />
CPB20582-3/8-PPB (BSPT)<br />
Cap Seal<br />
CP7717-2/121-EPR<br />
CP7717-2/121-VI, VITON ®<br />
Tip Seal<br />
Provides additional seal between<br />
tip and body<br />
CP7717-2/17-VI, VITON<br />
Retrofit Seal<br />
For headers with 27/32" (21 mm)<br />
diameter holes<br />
CP20580-BU SEAL, BUNA-N<br />
CP20580-VI SEAL, VITON<br />
Blank Tip<br />
QPA PLUG<br />
3
New<br />
Clip-Eyelet ® Nozzle Assembly<br />
Designed to ensure easy installation and minimal maintenance<br />
downtime, the No. 20570 — Clip-Eyelet nozzle assembly<br />
simply snaps onto an existing header. The nozzle tip is then<br />
installed, aligned, and secured by twisting the cap — all by<br />
hand. The assembly is affixed to the header by a spring grade<br />
stainless steel clamp which fits a 1", 1-1/4", 1-1/2", or 2" pipe.<br />
Whether you’re removing the entire assembly or just changing<br />
a spray tip, you’ll save time with the Clip-Eyelet nozzle<br />
assembly. All of the assembly’s parts are designed for easy<br />
handling. They’re clearly marked for quick identification, fit<br />
snugly into place, align easily, and require minimal attention.<br />
Double clamp and large inlet options<br />
The standard Clip-Eyelet nozzle assembly offers greater<br />
flexibility with the addition of double clamp and larger<br />
pipe inlet designs.<br />
The double clamp configuration enables spraying operations<br />
to sustain pressures up to 150 psi while the larger pipe inlet<br />
size for 21/32" openings, eliminates the need for retrofit seals.<br />
Each assembly is available with single or double clamp<br />
configurations and a choice of two inlet sizes to accommodate<br />
9/16" (14.5 mm) or 21/32" (17 mm) diameter drill holes.<br />
Built to withstand high temperature and<br />
corrosion<br />
Along with convenience, the Clip-Eyelet nozzle assembly<br />
offers the consistent spray patterns, even coverage, and<br />
chemical resistance needed for effective cleaning, coating,<br />
and rinsing. Manufactured of glass-reinforced polypropylene,<br />
the nozzle assembly withstands high temperatures and resists<br />
corrosion. It can operate at liquid temperatures up to 180˚F at<br />
100 psi (82˚C at 7 bar) in the double clamp design.<br />
Ball-type spray tips allow precise direction of<br />
flat or hollow cone spray<br />
More than 30 different configurations of spray tips are<br />
available for the Clip-Eyelet nozzle assembly. These ball-type<br />
flat and hollow cone spray tips allow the<br />
spray pattern to be directed very<br />
precisely at the surfaces being<br />
sprayed. The spray tips feature<br />
spray angles from 15° to 80°<br />
with capacities ranging from<br />
.35 to 12.2 gpm (1.2 to 46 l/min).<br />
Several additional spray tip options for<br />
extra versatility<br />
For added versatility, options include a threaded ball<br />
that accepts a wide variety of conventional nozzles; a blank<br />
spray tip which stops the<br />
flow of liquid; and a<br />
ProMax ® ball for use<br />
with ProMax FullJet ® ,<br />
VeeJet ® , and WhirlJet ®<br />
spray tips.<br />
4
Clip-Eyelet ® Nozzle Assembly <strong>Sp</strong>ecifications<br />
Dimensions & Weights<br />
A<br />
B<br />
<strong>Co</strong>lor<br />
<strong>Co</strong>lor<br />
To<br />
Dimensions<br />
20570 Clip-Eyelet<br />
Net<br />
<strong>Co</strong>ded<br />
<strong>Co</strong>ded<br />
Clamp<br />
Assembly No.<br />
Weight<br />
Body<br />
Cap<br />
On<br />
A B C<br />
C<br />
20570__-1-PP Medium Gray Light Gray 1" pipe<br />
20570 __-1-1/4-PP Medium Gray Light Gray 1-1/4" pipe<br />
20570 __ -1-1/2-PPB Black Light Gray 1-1/2" pipe<br />
20570 __ -2-PPB Black Light Gray 2" pipe<br />
1-3/4" 2-7/8" 1-7/8"<br />
(44 mm) (73 mm) (48 mm)<br />
1-7/8" 3-1/16" 1-7/8"<br />
(48 mm) (78 mm) (48 mm)<br />
2" 3-3/16" 1-7/8"<br />
(51 mm) (81 mm) (48 mm)<br />
2-3/8" 3-7/16" 1-15/16"<br />
(60 mm) (87 mm) (49 mm)<br />
2.7 oz.<br />
(.08 kg)<br />
2.7 oz.<br />
(.08 kg)<br />
3.2 oz.<br />
(.09 kg)<br />
3.2 oz.<br />
(.09 kg)<br />
Based on largest/heaviest version of each type.<br />
Ordering Info<br />
CLIP-EYELET NOZZLE<br />
ASSEMBLY AND SPRAY TIP<br />
ASSEMBLY SPRAY TIP *Clamp Design — (no designation) indicates Single Clamp; D indicates Double Clamp<br />
**Inlet Dia. — (no designation) indicates 9/16" (14.5 mm) dia.; L indicates 21/32" (17 mm) dia.<br />
20570 D L – 1 – PP + CT 50 30 – PP<br />
Nozzle *Clamp **Inlet Pipe Material Tip <strong>Sp</strong>ray Capacity Material<br />
Type Design Dia. Size <strong>Co</strong>de Type Angle Size <strong>Co</strong>de<br />
Clip-Eyelet Nozzle Assembly Options<br />
Body Assemblies<br />
To fit 9/16" (14.5 mm) or 21/32"<br />
(17 mm) dia. drilled pipe<br />
Double Clamp Body<br />
For pressures to 150 psi (10.3 bar)<br />
Single Clamp Body<br />
For pressures to 60 psi (4 bar)<br />
Ball-Type <strong>Sp</strong>ray Tip<br />
See pages 14 and 15<br />
Threaded Ball for Standard Nozzles<br />
For nozzles with 1/4" Male <strong><strong>Co</strong>nnect</strong>ion<br />
CP20582-1/4-PPB (NPT)<br />
CPB20582-1/4-PPB (BSPT)<br />
For nozzles with 3/8" Male <strong><strong>Co</strong>nnect</strong>ion<br />
CP20582-3/8-PPB (NPT)<br />
CPB20582-3/8-PPB (BSPT)<br />
Cap Seal<br />
CP7717-2/121-EPR<br />
CP7717-2/121-VI, VITON ®<br />
Retrofit Seal<br />
For headers with 27/32" (21 mm)<br />
diameter holes<br />
CP20580-BU SEAL, BUNA-N<br />
CP20580-VI SEAL, VITON<br />
Blank Tip<br />
CT PLUG – PP<br />
5
HP Eyelet Nozzle Assembly<br />
The No. 38625 — HP Eyelet is the first assembly of its kind<br />
that can be easily installed and removed by hand. The<br />
assembly’s hinged body only requires one screw for hand<br />
tightening to the spray header. The screw may be installed<br />
from either side of the assembly for easy access. It also<br />
remains attached to the assembly when loosened to eliminate<br />
the chance of loss or misplacement.<br />
The assembly features a square body for excellent stability.<br />
This helps prevent rotation when the retaining cap is removed<br />
or tightened. It operates at a maximum pressure of 125 psi<br />
(8.6 bar) and a maximum temperature of 180°F (82°C) —<br />
making it a good choice for metal pretreatment, food<br />
processing, electronics, chemical, and car/truck washing<br />
applications.<br />
Built to resist chemical attack<br />
The hinged body is molded of ProMax ® material, with a<br />
polyphthalamide cap, that combines strength and durability<br />
with chemical resistance. Plus, the smooth internal surfaces<br />
of the assembly resist scale and chemical build-up. The seal<br />
and O-ring are made of EPDM. A VITON ® seal and O-ring<br />
are optional.<br />
Easily retrofitted to existing piping systems<br />
Available for 1-1/4" or 1-1/2" pipe sizes, the HP Eyelet is<br />
designed to fit a 9/16" (14.5 mm) diameter predrilled pipe<br />
opening. The assembly can also be easily retrofitted to an<br />
existing system. Optional retrofit seals fit existing hole<br />
diameters of 21/32" (17 mm) or 27/32" (21 mm). For added<br />
convenience, the screw also accepts standard slotted head<br />
screwdrivers, #2 and<br />
#3 Phillips head<br />
screwdrivers, or 5/32"<br />
Allen wrenches.<br />
Choose from a<br />
variety of<br />
ball/tip options<br />
The HP Eyelet accepts four different ball/tip options.<br />
Included are color-coded ball-type spray tips; a ProMax<br />
<strong>Quick</strong>Jet ® ball for use with ProMax VeeJet ® , FullJet ® , and<br />
WhirlJet ® spray tips; a threaded ball for use with threaded<br />
spray nozzles; and a blank tip which blocks the liquid flow<br />
in a selected spray zone.<br />
6
HP Eyelet Nozzle Assembly <strong>Sp</strong>ecifications<br />
A<br />
B<br />
Dimensions & Weights<br />
38625<br />
C<br />
D<br />
Hinged<br />
<strong>Sp</strong>lit-Eyelet<br />
Body Assembly<br />
38625-1-1/4-PP<br />
38625-1-1/2-PP<br />
To<br />
Clamp<br />
On<br />
1-1/4" pipe<br />
1-1/2" pipe<br />
A<br />
B<br />
Dimensions<br />
C<br />
D<br />
Net<br />
Weight<br />
4-3/16" 1-1/4" 3-1/4" 1-3/4" 3.9 oz.<br />
(106 mm) (32 mm) (83 mm) (44 mm) (.11 kg.)<br />
4-5/16" 1-11/32" 3-1/2" 1-3/4" 3.9 oz.<br />
(110 mm) (34 mm) (89 mm) (44 mm) (.11 kg.)<br />
Based on largest/heaviest version of each type.<br />
Ordering Info<br />
PROMAX HP EYELET NOZZLE<br />
ASSEMBLY AND SPRAY TIP<br />
Ordering Info<br />
HP EYELET NOZZLE<br />
ASSEMBLY AND SPRAY TIP<br />
ASSEMBLY PROMAX BALL SPRAY TIP<br />
38625-1-1/4-PP+CP46679-PP+QPTA 25 02<br />
ASSEMBLY<br />
SPRAY TIP<br />
38625 – 1-1/4 – PP + CT 50 30 – PP<br />
Nozzle Pipe Material Ball Tip <strong>Sp</strong>ray Capacity<br />
Type Size <strong>Co</strong>de No. Type Angle Size<br />
Nozzle Pipe Material Tip <strong>Sp</strong>ray Capacity Material<br />
Type Size <strong>Co</strong>de Type Angle Size <strong>Co</strong>de<br />
HP Eyelet Nozzle Assembly Options<br />
Ball-Type <strong>Sp</strong>ray Tip<br />
See pages 14 and 15<br />
O-Ring Seal (Cap)<br />
CP7717-2/121-VI, VITON ®<br />
ProMax Ball and <strong>Sp</strong>ray Tip<br />
CP46679-PP+<strong>Sp</strong>ray Tip<br />
See pages 9-13<br />
Retrofit Seals<br />
For headers with 21/32" (17 mm) diameter holes<br />
CP20579-BU SEAL, BUNA-N<br />
CP20579-VI SEAL, VITON<br />
For headers with 27/32" (21 mm) diameter holes<br />
CP20580-BU SEAL, BUNA-N<br />
CP20580-VI SEAL, VITON<br />
Threaded Ball for Standard Nozzles<br />
For nozzles with 1/4" Male <strong><strong>Co</strong>nnect</strong>ion<br />
CP20582 - 1/4 - PPB (NPT)<br />
CPB20582 - 1/4 - PPB (BSPT)<br />
For nozzles with 3/8" Male <strong><strong>Co</strong>nnect</strong>ion<br />
CP20582-3/8- PPB (NPT)<br />
CPB20582-3/8- PPB (BSPT)<br />
Blank Tip<br />
QPA PLUG or CT PLUG - PP<br />
7
<strong>Co</strong>mmon Application Problems and Possible<br />
<strong>Quick</strong>-<strong><strong>Co</strong>nnect</strong> Nozzle System Solutions<br />
ProMax ® <strong>Quick</strong>Jet ® Clip-Eyelet ® Nozzle – flat spray<br />
ProMax <strong>Quick</strong>Jet Clip-Eyelet nozzles with a flat<br />
spray are used to clean automotive bodies and<br />
component parts in an electrocoat washer before<br />
painting.<br />
ProMax <strong>Quick</strong>Jet Clip-Eyelet Nozzle – full cone spray<br />
ProMax <strong>Quick</strong>Jet Clip-Eyelet nozzles with a full cone<br />
spray are used to cool canned tomato products on a<br />
line-type cooling conveyor.<br />
Clip-Eyelet Nozzle<br />
Clip-Eyelet nozzles are used for the pretreatment of<br />
aluminum channels prior to painting.<br />
HP Eyelet Nozzle<br />
HP Eyelet nozzles with ProMax flat spray tips are<br />
used to clean large, off-road construction equipment<br />
wheels.<br />
8
<strong>Sp</strong>ray Tips for the ProMax ® Clip-Eyelet ® Nozzle Assembly and ProMax HP Eyelet Nozzle Assembly<br />
ProMax <strong>Quick</strong> VeeJet ® <strong>Sp</strong>ray Tips Standard Angle<br />
Flat <strong>Sp</strong>ray <strong>Sp</strong>ecifications<br />
QPTA_10<br />
1.0 gpm<br />
(3.9 l/min)<br />
QPTA_15<br />
1.5 gpm<br />
(5.9 l/min)<br />
QPTA_20<br />
2.0 gpm<br />
(7.9 l/min)<br />
QPTA_30<br />
3.0 gpm<br />
(11.8 l/min)<br />
QPTA_40<br />
4.0 gpm<br />
(15.8 l/min)<br />
QPTA_50<br />
5.0 gpm<br />
(19.7 l/min)<br />
QPTA_60<br />
6.0 gpm<br />
(24 l/min)<br />
QPTA_70<br />
7.0 gpm<br />
(28 l/min)<br />
Capacities at 40 psi (3 bar).<br />
Performance Data<br />
<strong>Sp</strong>ray Angle<br />
at 40 psi<br />
Capacity<br />
Size<br />
<strong>Sp</strong>ray<br />
Tip<br />
<strong>Co</strong>lor<br />
25° 40° 50° 65° 80° 95°<br />
• * • • • • • 10 White<br />
• * • • • • • 15 Gray<br />
• * • • • • • 20 Black<br />
• • • • • • 30 Orange<br />
• • • • • • 40 Green<br />
• • • • • • 50 Yellow<br />
• • • • • • 60 Blue<br />
• • • • • • 70 Red<br />
*Not recommended below 7 psi.<br />
Capacity<br />
(gallons per minute)<br />
5 10 20 30 40 60 80 100 200<br />
psi psi psi psi psi psi psi psi psi<br />
.35 .50 .71 .86 1.0 1.2 1.4 1.6 2.2<br />
.53 .75 1.1 1.3 1.5 1.8 2.1 2.4 3.4<br />
.71 1.0 1.4 1.7 2.0 2.5 2.8 3.2 4.5<br />
1.1 1.5 2.1 2.6 3.0 3.7 4.2 4.7 6.7<br />
1.4 2.0 2.8 3.5 4.0 4.9 5.7 6.3 8.9<br />
1.8 2.5 3.5 4.3 5.0 6.1 7.1 7.9 11.2<br />
2.1 3.0 4.2 5.2 6.0 7.3 8.5 9.5 13.4<br />
2.5 3.5 4.9 6.1 7.0 8.6 9.9 11.1 15.7<br />
<strong>Sp</strong>ray Angle<br />
at 3 bar<br />
Capacity<br />
Size<br />
<strong>Sp</strong>ray<br />
Tip<br />
<strong>Co</strong>lor<br />
25° 40° 50° 65° 80° 95°<br />
• * • • • • • 10 White<br />
• * • • • • • 15 Gray<br />
•* • • • • • 20 Black<br />
• • • • • • 30 Orange<br />
• • • • • • 40 Green<br />
• • • • • • 50 Yellow<br />
• • • • • • 60 Blue<br />
• • • • • • 70 Red<br />
*Not recommended below 0.5 bar.<br />
Capacity<br />
(liters per minute)<br />
0.3 1 2 3 4 5 6 7 14<br />
bar bar bar bar bar bar bar bar bar<br />
1.2 2.3 3.2 3.9 4.6 5.1 5.6 6.0 8.5<br />
1.9 3.4 4.8 5.9 6.8 7.6 8.4 9.0 12.8<br />
2.5 4.6 6.5 7.9 9.1 10.2 11.2 12.1 17.1<br />
3.7 6.8 9.7 11.8 13.7 15.3 16.7 18.1 26<br />
5.0 9.1 12.9 15.8 18.2 20 22 24 34<br />
6.2 11.4 16.1 19.7 23 25 28 30 43<br />
7.5 13.7 19.3 24 27 31 33 36 51<br />
8.7 16.0 23 28 32 36 39 42 60<br />
9
<strong>Sp</strong>ray Tips for the ProMax ® Clip-Eyelet ® Nozzle Assembly and ProMax HP Eyelet Nozzle Assembly continued<br />
ProMax <strong>Quick</strong> FullJet ® <strong>Sp</strong>ray Tips Standard Angle<br />
Full <strong>Co</strong>ne <strong>Sp</strong>ray <strong>Sp</strong>ecifications<br />
QPHA1<br />
.19 gpm<br />
(.74 l/min)<br />
QPHA1.5<br />
.29 gpm<br />
(1.1 l/min)<br />
QPHA2<br />
.38 gpm<br />
(1.5 l/min)<br />
QPHA3<br />
.57 gpm<br />
(2.2 l/min)<br />
QPHA3.5<br />
.67 gpm<br />
(2.6 l/min)<br />
QPHA5<br />
.95 gpm<br />
(3.7 l/min)<br />
QPHA6.5<br />
1.3 gpm<br />
(4.8 l/min)<br />
QPHA8<br />
1.5 gpm<br />
(6.8 l/min)<br />
QPHA10<br />
1.9 gpm<br />
(7.4 l/min)<br />
QPHA15<br />
2.9 gpm<br />
(11.2 l/min)<br />
Capacities at 40 psi (3 bar).<br />
Performance Data<br />
<strong>Sp</strong>ray<br />
Tip<br />
Number<br />
<strong>Sp</strong>ray<br />
Tip<br />
<strong>Co</strong>lor<br />
Orifice<br />
Dia.<br />
Nom.<br />
Max.<br />
Free<br />
Passage<br />
Dia.*<br />
Capacity<br />
(gallons per minute)<br />
<strong>Sp</strong>ray<br />
Angle<br />
5 7 10 20 30 40 60 80 100 150 7 20 80<br />
psi psi psi psi psi psi psi psi psi psi psi psi psi<br />
QPHA1 <strong>Bro</strong>wn .035" .025" — — .10 .14 .17 .19 .23 .26 .30 .36 — 58° 53°<br />
QPHA1.5 White .045" .025" — .13 .15 .21 .25 .29 .35 .40 .44 .53 52° 65° 59°<br />
QPHA2 Gray .047" .040" .14 .17 .20 .28 .34 .38 .46 .53 .59 .70 43° 50° 46°<br />
QPHA3 Black .061" .040" .22 .26 .30 .42 .50 .57 .69 .79 .88 1.1 52° 65° 59°<br />
QPHA3.5 Orange .063" .050" .25 .30 .35 .48 .58 .67 .81 .92 1.0 1.3 43° 50° 46°<br />
QPHA5 Green .077" .050" .36 .42 .50 .69 .82 .95 1.2 1.3 1.5 1.8 52° 65° 59°<br />
QPHA6.5 Yellow .089" .063" .47 .55 .65 .89 1.1 1.3 1.5 1.7 1.9 2.3 45° 50° 46°<br />
QPHA8 Beige .096" .063" .58 .68 .80 1.1 1.3 1.5 1.8 2.1 2.3 2.9 54° 65° 61°<br />
QPHA10 Blue .113" .063" .73 .85 1.0 1.4 1.7 1.9 2.4 2.7 3.0 3.6 58° 67° 61°<br />
QPHA15 Red .141" .063" 1.1 1.3 1.5 2.1 2.5 2.9 3.5 4.0 4.4 5.3 80° 85° 80°<br />
<strong>Sp</strong>ray<br />
Tip<br />
Number<br />
<strong>Sp</strong>ray<br />
Tip<br />
<strong>Co</strong>lor<br />
Orifice<br />
Dia.<br />
Nom.<br />
mm<br />
Max.<br />
Free<br />
Passage<br />
Dia.*<br />
mm<br />
Capacity<br />
(liters per minute)<br />
<strong>Sp</strong>ray<br />
Angle<br />
0.5 0.7 1.5 2 3 4 5 6 7 10 0.5 0.7 6<br />
bar bar bar bar bar bar bar bar bar bar bar bar bar<br />
QPHA1 <strong>Bro</strong>wn .89 .64 — .38 .54 .62 .74 .85 .94 1.0 1.1 1.3 — 58° 53°<br />
QPHA1.5 White 1.1 .64 .49 .57 .81 .93 1.1 1.3 1.4 1.5 1.7 1.9 52° 65° 59°<br />
QPHA2 Gray 1.2 1.0 .65 .76 1.1 1.2 1.5 1.7 1.9 2.0 2.2 2.6 43° 50° 46°<br />
QPHA3 Black 1.5 1.0 .98 1.1 1.6 1.9 2.2 2.5 2.8 3.1 3.3 3.9 52° 65° 59°<br />
QPHA3.5 Orange 1.6 1.3 1.1 1.3 1.9 2.2 2.6 3.0 3.3 3.6 3.9 4.5 43° 50° 46°<br />
QPHA5 Green 2.0 1.3 1.6 1.9 2.7 3.1 3.7 4.2 4.7 5.1 5.5 6.5 52° 65° 59°<br />
QPHA6.5 Yellow 2.3 1.6 2.1 2.5 3.5 4.0 4.8 5.5 6.1 6.7 7.1 8.4 45° 50° 46°<br />
QPHA8 Beige 2.4 1.6 2.6 3.0 4.3 4.9 6.0 6.8 7.5 8.2 8.8 10.4 54° 65° 61°<br />
QPHA10 Blue 2.9 1.6 3.3 3.8 5.4 6.2 7.4 8.5 9.4 10.2 11.0 13.0 58° 67° 61°<br />
QPHA15 Red 3.6 1.6 4.9 5.7 8.1 9.3 11.2 12.7 14.1 15.4 16.5 19.4 80° 85° 80°<br />
*Foreign matter with maximum diameter as listed can pass through<br />
nozzle without clogging.<br />
10
<strong>Sp</strong>ray Tips for the ProMax ® Clip-Eyelet ® Nozzle Assembly and ProMax HP Eyelet Nozzle Assembly continued<br />
ProMax <strong>Quick</strong> FullJet ® <strong>Sp</strong>ray Tips Wide Angle<br />
Full <strong>Co</strong>ne <strong>Sp</strong>ray <strong>Sp</strong>ecifications<br />
QPHA2.8W<br />
.51 gpm<br />
(2.0 l/min)<br />
QPHA4.3W<br />
.79 gpm<br />
(3.1 l/min)<br />
QPHA5.6W<br />
1.0 gpm<br />
(4.0 l/min)<br />
QPHA8W<br />
1.5 gpm<br />
(5.8 l/min)<br />
QPHA10W<br />
1.8 gpm<br />
(7.2 l/min)<br />
QPHA12W<br />
2.2 gpm<br />
(8.7 l/min)<br />
QPHA14W<br />
2.6 gpm<br />
(10.1 l/min)<br />
Capacities at 40 psi (3 bar).<br />
Performance Data<br />
<strong>Sp</strong>ray<br />
Tip<br />
Number<br />
<strong>Sp</strong>ray<br />
Tip<br />
<strong>Co</strong>lor<br />
Orifice<br />
Dia.<br />
Nom.<br />
Max.<br />
Free<br />
Passage<br />
Dia.*<br />
Capacity<br />
(gallons per minute)<br />
<strong>Sp</strong>ray<br />
Angle<br />
5 7 10 15 20 30 40 60 80 5 10 80<br />
psi psi psi psi psi psi psi psi psi psi psi psi<br />
QPHA2.8W White .057" .040" — — .28 .33 .38 .45 .51 .61 .70 — 120° 102°<br />
QPHA4.3W Black .073" .040" — — .43 .51 .58 .70 .79 .95 1.1 — 120° 102°<br />
QPHA5.6W Orange .086" .040" — .48 .56 .67 .76 .91 1.0 1.2 1.4 — 120° 102°<br />
QPHA8W Green .098" .050" — .68 .80 .96 1.1 1.3 1.5 1.8 2.0 — 120° 103°<br />
QPHA10W Yellow .109" .050" .74 .86 1.0 1.2 1.4 1.6 1.8 2.2 2.5 112° 120° 103°<br />
QPHA12W Blue .129" .050" .89 1.0 1.2 1.4 1.6 1.9 2.2 2.6 3.0 114° 120° 103°<br />
QPHA14W Red .141" .063" 1.0 1.2 1.4 1.7 1.9 2.3 2.6 3.1 3.5 114° 120° 103°<br />
<strong>Sp</strong>ray<br />
Tip<br />
Number<br />
<strong>Sp</strong>ray<br />
Tip<br />
<strong>Co</strong>lor<br />
Orifice<br />
Dia.<br />
Nom.<br />
mm<br />
Max.<br />
Free<br />
Passage<br />
Dia.*<br />
mm<br />
Capacity<br />
(liters per minute)<br />
<strong>Sp</strong>ray<br />
Angle<br />
0.3 0.5 0.7 1 2 3 4 5 6 0.3 0.7 6<br />
bar bar bar bar bar bar bar bar bar bar bar bar<br />
QPHA2.8W White 1.4 1.0 — — 1.1 1.2 1.7 2.0 2.3 2.5 2.7 — 120° 102°<br />
QPHA4.3W Black 1.9 1.0 — — 1.6 1.9 2.6 3.1 3.5 3.9 4.2 — 120° 102°<br />
QPHA5.6W Orange 2.2 1.0 — 1.8 2.1 2.5 3.4 4.0 4.6 5.1 5.5 — 120° 102°<br />
QPHA8W Green 2.5 1.3 — 2.6 3.0 3.6 4.8 5.8 6.6 7.2 7.8 — 120° 103°<br />
QPHA10W Yellow 2.8 1.3 2.6 3.3 3.8 4.5 6.0 7.2 8.2 9.1 9.8 112° 120° 103°<br />
QPHA12W Blue 3.3 1.3 3.1 3.9 4.6 5.3 7.3 8.7 9.8 10.9 11.8 114° 120° 103°<br />
QPHA14W Red 3.6 1.6 3.7 4.6 5.3 6.2 8.5 10.1 11.5 12.7 13.7 114° 120° 103°<br />
*Foreign matter with maximum diameter as listed can pass through nozzle without clogging.<br />
11
<strong>Sp</strong>ray Tips for the ProMax ® Clip-Eyelet ® Nozzle Assembly and ProMax HP Eyelet Nozzle Assembly continued<br />
ProMax <strong>Quick</strong> WhirlJet ® <strong>Sp</strong>ray Tips Standard Angle and<br />
Wide Angle Hollow <strong>Co</strong>ne <strong>Sp</strong>ray <strong>Sp</strong>ecifications<br />
QPAA_<br />
QPAA_W<br />
Performance-Data Standard Angle<br />
<strong>Sp</strong>ray<br />
Tip<br />
Number<br />
Inlet<br />
Dia.<br />
Nom.<br />
Orifice<br />
Dia.<br />
Nom.<br />
Capacity<br />
(gallons per minute)<br />
<strong>Sp</strong>ray<br />
Angle<br />
3 5 7 10 20 30 40 60 80 100 7 20 80<br />
psi psi psi psi psi psi psi psi psi psi psi psi psi<br />
QPAA0.5 .031" .047" — — — .05 .07 .09 .10 .12 .14 .16 — 58° 69°<br />
QPAA1 .063" .063" — — — .10 .14 .17 .20 .24 .28 .31 — 64° 76°<br />
QPAA2 .078" .078" — .14 .17 .20 .28 .35 .40 .49 .57 .63 53° 70° 80°<br />
QPAA3 .094" .094" — .21 .23 .30 .43 .52 .60 .73 .85 .95 55° 79° 80°<br />
QPAA5 .141" .109" — .35 .42 .50 .70 .86 1.0 1.2 1.4 1.6 70° 75° 79°<br />
QPAA8 .172" .141" .44 .57 .67 .80 1.1 1.4 1.6 2.0 2.3 2.5 65° 72° 74°<br />
QPAA10 .188" .172" .55 .72 .84 1.0 1.4 1.7 2.0 2.4 2.8 3.1 70° 76° 75°<br />
QPAA15 .199" .203" .82 1.1 1.3 1.5 2.1 2.6 3.0 3.7 4.2 4.7 70° 72° 75°<br />
<strong>Sp</strong>ray<br />
Tip<br />
Number<br />
Inlet<br />
Capacity<br />
Orifice<br />
<strong>Sp</strong>ray<br />
Dia.<br />
(liters per minute)<br />
Dia.<br />
Angle<br />
Nom.<br />
Nom.<br />
mm mm 0.2 0.5 1 1.5 2 3 4 5 6 7 0.5 1.5 6<br />
bar bar bar bar bar bar bar bar bar bar bar bar bar<br />
QPAA0.5 .79 1.2 — .16 .23 .28 .32 .39 .46 .51 .56 .60 — 58° 69°<br />
QPAA1 1.6 1.6 — .32 .46 .56 .64 .79 .91 1.0 1.1 1.2 — 64° 76°<br />
QPAA2 2.0 2.0 — .64 .91 1.1 1.3 1.6 1.8 2.0 2.2 2.4 53° 70° 80°<br />
QPAA3 2.4 2.4 — .97 1.4 1.7 1.9 2.4 2.7 3.1 3.3 3.6 55° 79° 80°<br />
QPAA5 3.6 2.8 — 1.6 2.3 2.8 3.2 3.9 4.6 5.1 5.6 6.0 70° 75° 79°<br />
QPAA8 4.4 3.6 1.6 2.6 3.6 4.5 5.2 6.3 7.3 8.2 8.9 9.6 65° 72° 74°<br />
QPAA10 4.8 4.4 2.0 3.2 4.6 5.6 6.4 7.9 9.1 19.2 11.2 12.1 70° 76° 75°<br />
QPAA15 6.0 5.2 3.1 4.8 6.8 8.4 9.7 11.8 13.7 15.3 16.7 18.1 70° 72° 75°<br />
12
<strong>Sp</strong>ray Tips for the ProMax ® Clip-Eyelet ® Nozzle Assembly and ProMax HP Eyelet Nozzle Assembly continued<br />
ProMax <strong>Quick</strong> WhirlJet ® <strong>Sp</strong>ray Tips Standard Angle and<br />
Wide Angle Hollow <strong>Co</strong>ne <strong>Sp</strong>ray <strong>Sp</strong>ecifications continued<br />
Performance Data-Wide Angle<br />
<strong>Sp</strong>ray<br />
Tip<br />
Number<br />
Inlet<br />
Dia.<br />
Nom.<br />
Orifice<br />
Dia.<br />
Nom.<br />
Capacity<br />
(gallons per minute)<br />
<strong>Sp</strong>ray<br />
Angle<br />
3 5 7 10 20 30 40 60 80 100 7 20 80<br />
psi psi psi psi psi psi psi psi psi psi psi psi psi<br />
QPAA5W .136" .129" — .35 .42 .50 .70 .86 1.0 1.2 1.4 1.6 125° 112° 98°<br />
QPAA8W .177" .156" .44 .57 .67 .80 1.1 1.4 1.6 2.0 2.3 2.5 112° 100° 87°<br />
QPAA10W .196" .177" .55 .72 .84 1.0 1.4 1.7 2.0 2.4 2.8 3.1 111° 97° 89°<br />
QPAA15W .242" .213" .82 1.1 1.3 1.5 2.1 2.6 3.0 3.7 4.2 4.7 110° 98° 90°<br />
<strong>Sp</strong>ray<br />
Tip<br />
Number<br />
Inlet<br />
Dia.<br />
Nom.<br />
mm<br />
Orifice Dia.<br />
Nom.<br />
mm<br />
Capacity<br />
(liters per minute)<br />
<strong>Sp</strong>ray<br />
Angle<br />
0.2 0.5 1 1.5 2 3 4 5 6 7 0.5 1.5 6<br />
bar bar bar bar bar bar bar bar bar bar bar bar bar<br />
QPAA5W 3.5 3.3 — 1.6 2.3 2.8 3.2 3.9 4.6 5.1 5.6 6.0 125° 112° 98°<br />
QPAA8W 4.5 4.0 1.6 2.6 3.6 4.5 5.2 6.3 7.3 8.2 8.9 9.6 112° 100° 87°<br />
QPAA10W 5.0 4.5 2.0 3.2 4.6 5.6 6.4 7.9 9.1 10.2 11.2 12.1 111° 97° 89°<br />
QPAA15W 6.1 5.4 3.1 4.8 6.8 8.4 9.7 11.8 13.7 15.3 16.7 18.1 110° 98° 90°<br />
<strong>Quick</strong> connect nozzles are mounted on an overhead conveyor system in a five section parts washer.<br />
13
<strong>Sp</strong>ray Tips for the Clip-Eyelet ® Nozzle Assembly and HP Eyelet Nozzle Assembly<br />
Flat <strong>Sp</strong>ray Tips Standard Angle <strong>Sp</strong>ray <strong>Sp</strong>ecifications<br />
CT_10<br />
1.0 gpm<br />
(3.9 l/min)<br />
CT_20<br />
2.0 gpm<br />
(7.9 l/min)<br />
CT_30<br />
3.0 gpm<br />
(11.8 l/min)<br />
CT_40<br />
4.0 gpm<br />
(15.8 l/min)<br />
CT_50<br />
5.0 gpm<br />
(19.7 l/min)<br />
CT_60<br />
6.0 gpm<br />
(24 l/min)<br />
CT_70<br />
7.0 gpm<br />
(28 l/min)<br />
CT_100<br />
10.0 gpm<br />
(39 l/min)<br />
Capacities at 40 psi (3 bar).<br />
Performance Data<br />
<strong>Sp</strong>ray Angle<br />
at 40 psi<br />
Cap.<br />
Size<br />
Tip<br />
<strong>Co</strong>lor<br />
15° 25° 40° 50° 65° 80°<br />
— — — — CT6510-PP CT8010-PP 10 Beige<br />
— — CT4020-PP CT5020-PP CT6520-PP — 20 Light Blue<br />
— CT2530-PP CT4030-PP CT5030-PP CT6530-PP — 30 Orange<br />
— — CT4040-PP CT5040-PP CT6540-PP CT8040-PP 40 Green<br />
CT1550-PP — CT4050-PP CT5050-PP CT6550-PP — 50 Yellow<br />
— CT2560-PP CT4060-PP CT5060-PP CT6560-PP CT8060-PP 60 Blue<br />
CT1570-PP CT2570-PP CT4070-PP CT5070-PP CT6570-PP CT8070-PP 70 Red<br />
CT15100-PP CT25100-PP CT40100-PP CT50100-PP CT65100-PP CT80100-PP 100 <strong>Bro</strong>wn<br />
Capacity<br />
(gallons per minute)<br />
5 7 10 20 30 40 60<br />
psi psi psi psi psi psi psi<br />
.35 .42 .50 .71 .86 1.0 1.2<br />
.71 .84 1.0 1.4 1.7 2.0 2.5<br />
1.1 1.3 1.5 2.1 2.6 3.0 3.7<br />
1.4 1.7 2.0 2.8 3.5 4.0 4.9<br />
1.8 2.1 2.5 3.5 4.3 5.0 6.1<br />
2.1 2.5 3.0 4.2 5.2 6.0 7.3<br />
2.5 2.9 3.5 4.9 6.1 7.0 8.6<br />
3.5 4.2 5.0 7.1 8.6 10.0 12.2<br />
<strong>Sp</strong>ray Angle<br />
at 3 bar<br />
Cap.<br />
Size<br />
Tip<br />
<strong>Co</strong>lor<br />
15° 25° 40° 50° 65° 80°<br />
— — — — CT6510-PP CT8010-PP 10 Beige<br />
— — CT4020-PP CT5020-PP CT6520-PP — 20 Light Blue<br />
— CT2530-PP CT4030-PP CT5030-PP CT6530-PP — 30 Orange<br />
— — CT4040-PP CT5040-PP CT6540-PP CT8040-PP 40 Green<br />
CT1550-PP — CT4050-PP CT5050-PP CT6550-PP — 50 Yellow<br />
— CT2560-PP CT4060-PP CT5060-PP CT6560-PP CT8060-PP 60 Blue<br />
CT1570-PP CT2570-PP CT4070-PP CT5070-PP CT6570-PP CT8070-PP 70 Red<br />
CT15100-PP CT25100-PP CT40100-PP CT50100-PP CT65100-PP CT80100-PP 100 <strong>Bro</strong>wn<br />
Capacity<br />
(liters per minute)<br />
0.3 .7 1 1.5 2 3 4<br />
bar bar bar bar bar bar bar<br />
1.2 1.9 2.3 2.8 3.2 3.9 4.6<br />
2.5 3.8 4.6 5.6 6.5 7.9 9.1<br />
3.7 5.7 6.8 8.4 9.7 11.8 13.7<br />
5.0 7.6 9.1 11.2 12.9 15.8 18.2<br />
6.2 9.5 11.4 14.0 16.1 19.7 23<br />
7.5 11.4 13.7 16.7 19.3 24 27<br />
8.7 13.3 16.0 19.5 23 28 32<br />
12.5 19.1 23 28 32 39 46<br />
14
<strong>Sp</strong>ray Tips for the Clip-Eyelet ® Nozzle Assembly and HP Eyelet Nozzle Assembly continued<br />
Hollow <strong>Co</strong>ne <strong>Sp</strong>ray Tips Standard Angle <strong>Sp</strong>ray <strong>Sp</strong>ecifications<br />
CA15-30.1<br />
4.5 gpm<br />
(17.6 l/min)<br />
CA25-30.1<br />
5.4 gpm<br />
(21.4 l/min)<br />
CA50-50.1<br />
9.9 gpm<br />
(39.2 l/min)<br />
CA50-50.3<br />
9.8 gpm<br />
(38.7 l/min)<br />
Capacities at 40 psi (3 bar).<br />
Performance Data<br />
Tip and Vane<br />
Sub-assembly<br />
No.<br />
Capacity<br />
(gallons per minute)<br />
<strong>Sp</strong>ray Angle<br />
at 40 psi<br />
5 10 20 30 40 50 60 7 20 60<br />
psi psi psi psi psi psi psi psi psi psi<br />
CA15-30.1-PP 1.6 2.3 3.2 3.9 4.5 5.0 5.4 46° 49° 51°<br />
CA25-30.1-PP 2.0 2.8 3.9 4.7 5.4 6.1 6.6 45° 47° 50°<br />
CA50-50.1-PP 3.5 5.0 7.0 8.6 9.9 11.1 12.1 38° 46° 48°<br />
CA50-50.3-PP 3.5 5.0 7.1 8.5 9.8 10.9 11.9 75° 75° 76°<br />
Tip and Vane<br />
Sub-assembly<br />
No.<br />
Capacity<br />
(liters per minute)<br />
<strong>Sp</strong>ray Angle<br />
at 3 bar<br />
0.35 .7 1 1.5 2 3 4 0.5 1.5 4<br />
bar bar bar bar bar bar bar bar bar bar<br />
CA15-30.1-PP 6.2 8.8 10.4 12.6 14.5 17.6 20.2 46° 49° 51°<br />
CA25-30.1-PP 7.5 10.7 12.7 15.4 17.6 21.4 24.6 45° 47° 50°<br />
CA50-50.1-PP 13.5 19.0 22.7 27.8 32.0 39.2 45.2 38° 46° 48°<br />
CA50-50.3-PP 13.5 19.0 22.7 27.6 31.8 38.7 44.4 75° 75° 76°<br />
15
Other helpful resources and<br />
product information for specifying<br />
spray nozzles<br />
Industrial <strong>Sp</strong>ray Products Catalog 60B<br />
Our new 524-page catalog features<br />
tens of thousands of spray system<br />
solutions. You’ll find design features,<br />
performance data, dimensions and<br />
weights, and ordering information all<br />
in a readable and easy-to-follow<br />
format. Request Catalog 60B.<br />
ProMax ® <strong>Quick</strong>Jet ® Nozzles Bulletin<br />
This newly revised bulletin highlights<br />
<strong><strong>Sp</strong>raying</strong> <strong>Systems</strong> <strong>Co</strong>.’s expanded line<br />
of ProMax nozzles. The time-saving<br />
installation and maintenance features<br />
of this nozzle, including easy-to-install<br />
and replace spray tips, are described in<br />
detail. Request Bulletin No. 514.<br />
WindJet ® Air Knife & WindJet<br />
Air Knife Drying Packages<br />
This 20-page bulletin presents<br />
components and performance data<br />
on WindJet ® Air Knives and<br />
completely customizable WindJet<br />
Air Knife Drying Packages. For<br />
assembly, the brochure provides<br />
tables and configuration charts<br />
differentiated by the horsepower<br />
size of the blower. Request Bulletin 543.<br />
<strong>Sp</strong>ray System Optimization Handbook<br />
This 52-page, illustrated handbook is<br />
packed with tips for improving production<br />
efficiency through spray nozzle maintenance<br />
and automation. It details system<br />
problems, common causes of problems<br />
and viable solutions. It also includes steps<br />
on defining performance standards,<br />
solving spray problems, and setting up<br />
your own maintenance programs.<br />
Request Technical Manual No. 410.<br />
Metal Pre-Treatment Bulletin<br />
This 12-page bulletin includes information<br />
on spray nozzles for<br />
improving finished product quality in<br />
the surface treatment process.<br />
Included are applications and specifications<br />
on many spray nozzles and<br />
accessories designed for surface<br />
treatment. Request Bulletin No. 354E.<br />
Air <strong>Co</strong>ntrol Application<br />
Performance Guide<br />
This 28-page catalog is a comprehensive<br />
guide to improving the<br />
performance of your air control applications.<br />
The catalog reviews nozzle<br />
basics, application solutions, system<br />
automation and engineering data. It<br />
covers product information on<br />
nozzles, manifolds, lances, air guns<br />
and accessories. Request Catalog 20.<br />
With more than 60 years of helping customers solve spray problems and experience in over 200 industries, <strong><strong>Sp</strong>raying</strong> <strong>Systems</strong> <strong>Co</strong>.<br />
is the world leader in spray technology. Our comprehensive spray solutions incorporate 80,000 spray nozzles, turnkey systems,<br />
spray research and analysis services, and custom fabrication. All of our products and services are engineered with one goal<br />
in mind — optimizing your spray system.<br />
P.O. Box 7900 • Wheaton, Illinois 60189-7900 USA<br />
Phone 1-800-95-SPRAY • Fax 1-888-95-SPRAY<br />
Outside the U.S., Phone 1(630) 665-5000 • Fax 1(630) 260-0842<br />
Visit our Web Site: http://www.spray.com<br />
Represented by:<br />
Bulletin No. 513B<br />
Printed in U.S.A. ©<strong><strong>Sp</strong>raying</strong> <strong>Systems</strong> <strong>Co</strong>. 2003