Technical Data Sheet - TSE Industries, Inc.

TECHNICAL DATA SHEET
TSE EcoSPRAY ® 92A Coating
Elastomeric Spray Coating
Product Description
TSE EcoSPRAY ® 92A is a two component urethane hybrid aromatic elastomer with a
Shore A hardness of 92A. The system has good UV stability and can be sprayed in
high humidity conditions, with minimal effect on physical properties. EcoSPRAY
provides good corrosion and abrasion resistance to most substrates. It retains its
elasticity through a temperature range or -30 O F to 200 O F. EcoSPRAY 92A can be
pigment to almost any color.
Applications include; protective coatings for pipes, tanks, concrete, wood and foams,
agricultural and mining equipment, boats, utility trailers, bed liners rapid mold
making and many more.
Features
100% Solids with Zero VOC
Higher Green Strengths
Benefits
Physical Properties
- Tougher & Stronger
- Non-Brittle
- Faster Cycle Times
Customizable to Individual
Specifications
Improved product quality
and consistency
Manufactured in ISO 9001 Increased batch-to-batch
certified plants
consistency and quality
THE INFORMATION HEREIN IS BELIEVED TO BE CORRECT AND RELIABLE. HOWEVER, NO WARRANTY IS EXPRESSED OR IMPLIED REGARDING THE
ACCURACY OF THESE DATA, AND NONE IS MADE AS TO THE MARKETABILITY OF THE MATERIAL OR ITS FITNESS FOR ANY PURPOSE. THE CONSUMER
ACCEPTS THE RESPONSIBILITY OF AND THE CONDITIONS FOR LIABILITY OF USE OF THE PRODUCT.
TSE INDUSTRIES, INC. CLEARWATER, FL 33760 (727) 573-7676
Tech Data TSE-EcoSPRAY ® 92A Page 1 of 3 EFF: 07/1/2012

Typical Liquid Properties (75ºF)
TSE EcoSPRAY ® 92A (Part A) Isocyanate
Viscosity, cps 2,500
Specific Gravity 1.09
Color
Clear
NCO% 9.8
Flash Point (Seta Closed Cup), ºF
N/A
Shelf Life
12 months
TSE-EcoSPRAY ® 92A (Part B) Resin
Viscosity, cps 1,500
Specific Gravity 1.05
Color
Clear brown
Hydroxyl Number 130
Shelf Life
12 months
Note: The gel time when reacted at 1:1 by volume is typically
varied from 15 to 30 seconds, based on the application.
Typical Mechanical Properties
Plaque
Casting
Shore A Hardness 92
Specific Gravity 1.06
Elongation, % 480
Tensile Strength, PSI 2,200
Taber Abrasion, mg/loss 155
(H-18 Wheel 1,000-g Load
1,000 cycles)
Tear Strength, Die C, lbf/in 410
Processing and Application
TSE EcoSPRAY 92 can be applied using both high and low pressure equipment and 2
component cartridge guns. It is essential to have equipment that consistently
delivers accurate amounts of both components to the mixer to obtain a high quality
elastomer.
Surfaces should be clean and free of contaminates
THE INFORMATION HEREIN IS BELIEVED TO BE CORRECT AND RELIABLE. HOWEVER, NO WARRANTY IS EXPRESSED OR IMPLIED REGARDING THE
ACCURACY OF THESE DATA, AND NONE IS MADE AS TO THE MARKETABILITY OF THE MATERIAL OR ITS FITNESS FOR ANY PURPOSE. THE CONSUMER
ACCEPTS THE RESPONSIBILITY OF AND THE CONDITIONS FOR LIABILITY OF USE OF THE PRODUCT.
TSE INDUSTRIES, INC. CLEARWATER, FL 33760 (727) 573-7676
Tech Data TSE-EcoSPRAY ® 92A Page 2 of 3 EFF: 07/1/2012

EcoSPRAY 85A can be applied in thicknesses from of 10 to100 mils or greater.
Storage
Processing Temperature*
50 O F – 140 O F
Mix Ratio, by Volume 1/1
Gel Time
15 sec
Tack-Free
2 min
Handling
10 – 30 min
*Depends on equipment used.
Store both TSE EcoSPRAY ® 92A (Part A) and TSE EcoSPRAY ® 92A (Part B) in tightly
closed containers and protected from contamination from moisture and foreign
substances, which can adversely affect processing. Any opened packages should be
blanketed using dry gas and resealed tightly so as to keep moisture from entering the
sealed container. TSE EcoSPRAY ® 85A (Part A) will react with water to form ureas
and CO2 gas, which may cause sealed containers to expand and rupture. For
maximum storage life, sealed containers should be stored between 60ºF and 95ºF.
Shelf life is 6 months when stored this way.
Standard Package
Components are supplied in 5-gallon pails (40 Lbs. net) and 55-gallon drums (450-
500 Lbs. net)
Safety and Handling
Refer to the Material Safety Data Sheet (MSDS) before handling either TSE
EcoSPRAY ® 85A (Part A) or TSE EcoSPRAY ® 85A (Part B). When spray applying these
materials, proper protective equipment must be worn. This should include a full face
breathing air mask and clothing to prevent skin contact with aerosol. It is the
responsibility of the operator to completely read and understand the MSDS for each
component before handling them.
If for any reason you are not clear on the proper safety and handling procedures
please contact your supervisor or a TSE representative for additional information.
THE INFORMATION HEREIN IS BELIEVED TO BE CORRECT AND RELIABLE. HOWEVER, NO WARRANTY IS EXPRESSED OR IMPLIED REGARDING THE
ACCURACY OF THESE DATA, AND NONE IS MADE AS TO THE MARKETABILITY OF THE MATERIAL OR ITS FITNESS FOR ANY PURPOSE. THE CONSUMER
ACCEPTS THE RESPONSIBILITY OF AND THE CONDITIONS FOR LIABILITY OF USE OF THE PRODUCT.
TSE INDUSTRIES, INC. CLEARWATER, FL 33760 (727) 573-7676
Tech Data TSE-EcoSPRAY ® 92A Page 3 of 3 EFF: 07/1/2012