. INSTRUCTIONS - Dectane
. INSTRUCTIONS - Dectane
. INSTRUCTIONS - Dectane
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
. <strong>INSTRUCTIONS</strong><br />
for daytime running lamps panel from Audi A3 8P<br />
autocouture<br />
1<br />
2<br />
3<br />
4<br />
5<br />
6<br />
7<br />
8<br />
9<br />
10<br />
11<br />
12<br />
13<br />
14<br />
15<br />
16<br />
Picture 1<br />
Pictures 2-4<br />
Pictures 5-8<br />
To release the original air inlet or fog lamp panel leverage carefully the hooks<br />
(see picture 1, white arrows)<br />
Take the panel and pull it out. Proceed in the same way with the other side.<br />
Unlock the cover of fuse box at A positions (please see picture 5) and release it in top direction.<br />
Pictures 9-13 On fuse box, middle right is located fuse place F15 or F14 (up to model) – ignition +12V<br />
Pull out the fuse and fit it into the delivered cable, in the lower fuse place. Then fit the hole<br />
fuse holder back to the fuse place F14/F15.<br />
Pictures 14-16<br />
In B point is located a silicon place for the cable of the fuse box. Include the cable along<br />
and close the cover from the fuse box.
. <strong>INSTRUCTIONS</strong><br />
for daytime running lamps panel from Audi A3 8P<br />
autocouture<br />
17<br />
18<br />
19<br />
20<br />
21<br />
22<br />
23<br />
24<br />
25<br />
26<br />
27<br />
28<br />
29 30 31<br />
Pictures 17-22<br />
Pictures 23-28<br />
Pictures 29-31<br />
Between point C (fuse box) and point D (headlight) is located the main conector of the<br />
headlight (point S). Take out the connector (point S) and adapt the y-piece from the<br />
delivered cable. Take care by locking, you must hear the “click” while closing the connectors.<br />
Install the Y piece cable between fuse box and headlight.<br />
Lay out the short cable with 3 pin connector (point E) sideway between headlight,<br />
to pull it out on bumper hole. Take the drl-panel (modulite) and connect the cables from F<br />
to those from E.<br />
Put the long cable with 3 pin connector along point H to bumperhole on the other side.
. <strong>INSTRUCTIONS</strong><br />
for daytime running lamps panel from Audi A3 8P<br />
autocouture<br />
32 33 34<br />
35<br />
36 37<br />
38<br />
39<br />
Pictures 32-33<br />
Pictures 34-39<br />
Do there the same procedure to connect the drl-panel again. Take care where you lay out the<br />
cable, that it would not be damaged or scratched.<br />
Finally fit the ground cable with the eye nut on central ground point of car. Release the cap nut<br />
(point J) with a 13mm spanner and assemble it again including the eye nut.<br />
Finally controll the laying from cable, take attention (not to be scratched or damaged, check it in<br />
order to avoid short circuits). Finally you can turn on ignition and check the functions!<br />
Function test:<br />
1. ignition on – drl on automatically!<br />
2. turn on the light – drl lights dimmed<br />
3. ignition off – dlr stays for around 20 seconds on and then switches off. IT RUNS!
. <strong>INSTRUCTIONS</strong><br />
for daytime running lamps panel from Audi A3 8P<br />
autocouture<br />
Please check the regulation under public law of your country!!!<br />
Please check the legal minimum amount on the vehicle from the lower edge 250 mm from<br />
the road surface. Between 250 - 350mm TFL must be turned off, dimmed from 350 mm<br />
height.