Datasheets - iLight

Lighting Controls 

iLight User Interfaces 

Kensington 

Kensington Control Panel Range 

Key Features 

• Designed to match Hamilton 

Hartland CFX Series 

• 4 standard finishes plus custom 

finishes available to order 

• Up to 10 buttons per panel 

• White LED indication on each button 

• All button functions are programmable - 

inc. 16 sequences 

• Engraving options on buttons or plate 

• Hidden RJ12 programming socket or IR 

receiver option in place of button 10 

• EEPROM program and sequence 

memory 

• Future proof with flash memory 

• CE compliant to all relevant standards 

• Designed and manufactured to 

ISO9001:2008 standards 

Overview 

These control panels provide the 

interface between the user and the 

remote dimmer or ballast power 

control devices connected together 

using the iLight control network. 

Installed in standard single gang 

UK style electrical wallboxes and 

connected by LV cable, these versatile 

units can be installed in any chosen 

position to suit the layout. 

Control panels perform a number of 

tasks. Buttons allow users to select 

lighting scenes, raise or lower levels, 

or select any other programmed 

system function including sequences. 

Multiple control plates may be used 

in each area and will communicate 

with each other to always show the 

function selected irrespective of 

which control plate selected it. Plates 

with the program function activated 

will allow lighting scenes to be 

re-programmed locally when required.

Button Functions 

Scene selection 

Scene raise/lower 

Channel raise/lower 

Toggle on/off 

Toggle raise/lower 

True off 

Open/close (for curtains or blinds) 

Raise/lower (for motorized screens) 

Task (start/stop a sequence) 

Dimensions 

FRONT 

COVER 

SCREWS 

CONTROL 

PANEL 

Infra Red Receiver - When fitted takes 

place of bottom button 

Mechanical Data 

Ordering Codes 

Control Cable Access: 

Standard UK wallbox, 35mm deep 

minumum (not supplied). 

Standard European backbox, 40mm deep 

minumum (not supplied) 

Temperature: +2ºC to +40ºC 

Humidity: +5 to 95% non condensing 

Control Inputs: 

One set of terminals for the iLight 

iCANnet TM network 

Recommended cable: Belden 1502 

Electrical Data 

Supply: +12V (via iCANnet TM cable) 

Terminal Sizes: 

Network cable size: 5 x 1mm 2 

Memory: 

FLASH memory to be able to upgrade 

firmware 

EEPROM for program and sequence 

memory 

Typlical Schematic 

Contact your local Eaton office 

20 Greenhill Crescent, Watford Business Park, 

Watford, Herts, WD18 8JA. UK 

T: +44 (0)1923 495496 F: +44 (0)1923 228796 

E: enquiries@iLight.co.uk www.iLight.co.uk 

Eaton Industries Manufacturing GmbH 

Electrical Sector EMEA 

Route de la Longeraie 

71110 Morges, Switzerland 

Eaton.eu 

© 2015 Eaton 

All Rights Reserved 

Document No: KENSINGTON Rev3 1114 

Changes to the products, to the information 

contained in this document, and to prices are 

reserved; so are errors and omissions. 

Eaton is a registered trademark. 

All other trademarks are property 

of their respective owners.



CLASSIC 

Classic Control Panel Range 

Key Features 

• Designed to match Wandsworth Series 2 

or Series 3 metal Panels with 15 finishes 

available 

• Other special finishes to order 

• Up to 10 buttons per panel (single gang) or 

20 buttons (double gang) 

• Buttons have integral indication of active 

button 

• Blue LED indication on each button 

• All button functions are programmable - 

includes 8 sequences 

• Engraving options on buttons or plate 

• Hidden RJ12 programming socket or IR 

receiver option in place of button 10 

• Keyswitch option 

• Eeprom program and sequence memory 


• Future proof with FLASH memory 



Overview 

These control panels provide the 

interface between the user and the 

remote dimmer. Installed in standard 

single or double gang UK style electrical 

wallboxes and connected to the dimmer 

by LV cable, these versatile units can be 

installed in any chosen position to suit the 

layout. 

Control Panels perform a number of tasks. 

Their buttons allow users to select lighting 

scenes, raise or lower levels, or select 

any other programmed system function. 

If the Program function is set, they allow 

lighting scenes to be programmed locally, 

and their RJ12 socket, when connected 

to a suitable iCANsoft computer, allows 

full remote access to the whole iLight 

network. It is possible to have more than 

one control panel in an area. When used 

in this way the indicators in the buttons 

will show which function is selected in 

the area irrespective of which control 

panel activated it.





Toggle on/off 


True off 






Double Gang Examples 

Dimensions 

86 mm - Single Gang 

146 mm - Double Gang 

39.01 mm 


Control Cable Access: via standard 35mm 

deep UK wallbox – not provided 



Control Inputs: One set of terminals for the 

iLight iCANnet TM network 

Suitable for Belden 1502 

86 mm 





iLight network cable size: 5 x 1mm 2 

Memory: 


firmware 


memory 





T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: CLASSIC Rev8 0614 









ARCHITRAVE 

Architrave Control Panel Range 

Key Features 

• Screwless flush mounting 

• Available in brushed stainless steel as 

standard 

• Other finishes to special order 


• Buttons have blue LED when active 

• All button functions are programmable 

• Supplied with custom wallbox 

• Programmable - 16 sequences with up to 

128 steps per sequence 

• IR option - Standard RC5 or B&O 




ISO9001:2008 standards. 

Overview 

The Architrave control panel range provides 

the interface between the user and the remote 

dimmer. Provided with a custom wallbox and 

connected to the dimmer by LV cable, these 

versatile units can be installed in any chosen 

position will limited wall space to suit the 

layout. These control panels dim the lighting 

intensity to a recorded level or initiate a 

programmed sequence of events over time by 

a simple button push. 

There are also five other standard control plate 

ranges available, see our Kensington, Classic, 

Classic Plus, Ineo and Revio ranges as well as a 

selection of touch screen user interfaces. 

Control Panels perform a number of tasks. Their 

buttons allow users to select lighting scenes, 

raise or lower levels, or select any other 

programmed system function. If the Program 

function is set, they allow lighting scenes to 

be programmed locally. It is possible to have 

more than one control panel in an area. When 

used in this way the indicators in the buttons 

will show which function is selected in the area 

irrespective of which control panel activated it.





Toggle on/off 


True off 




Dimensions 

Infra Red Receiver - When fitted takes place 

of bottom button 


Control Cable Access: 4 x 20mm knockouts 

- Custom wallbox provided 

Climate Range: IP20 




One set of terminals for the iLight network 


Note: These panels do not include a 

network programming point 





iCANnet TM network cable size: 5 x 1mm 2 

Memory: 


firmware 


memory 





T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: ARCHITRAVE Rev8 0614 









CLASSIC PLUS 

Classic Plus Control Panel Range 

Key Features 

• Screwless design matches 

Wandsworth Series 3 metal Plates 

• Other special finishes to order 


• Blue LED indication on each button 

• All button functions are 

programmable 

• Programmable - 16 sequences with 

up to 128 steps per sequence 

• CE compliant to all relevant 

standards 



ISO9001:2008 standards. 

Overview 

The Classic Plus control panels provide the 

interface between the user and the remote 

dimmer. Installed in a standard single gang 

Euro DIN wallbox or a UK style electrical 

wallbox. Connected to the dimmer by LV cable, 

these versatile units can be installed in any 

chosen position to suit the layout. These single 

gang control panels dim the lighting intensity 

to a recorded level or initiate a programmed 

sequence of events over time by a simple 

button push. 

There are also five other control plate ranges 

available, see our Sencia range, Classic range, 

Revio range, Ineo range and the Architrave 

range. 

Control Panels perform a number of tasks. 

Their buttons allow users to select lighting 

scenes, raise or lower levels, or select any 

other programmed system function. If the 

Program function is set, they allow lighting 

scenes to be programmed locally. It is possible 

to have more than one control panel in an area. 

When used in this way the indicators in the 

buttons will show which function is selected 

in the area irrespective of which control panel 

activated it.





Toggle on/off 


True off 




Fits both Euro DIN and UK standard wallbox types. 

Dimensions 




Control Cable Access: via standard UK 

35mm deep wallbox or Euro DIN wallbox 

– not provided 



Control Inputs: One set of terminals for the 

iLight iCANnet TM network 


Note: This panel does not include a 

network programming point 



Supply: +12V (via iCANnet TM ) 


iCANnet TM cable size: 5 x 1mm 2 

Memory: 


firmware 


memory 





T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: CLASSIC PLUS Rev6 0614 









Ineo 

Ineo Control Panel Range 

Key Features 

• Available in Black, White & Ivory 

finishes 

• Standard or custom engraving 

on buttons 



Overview 

Ineo is a versatile range of specification 

grade control panels that set new 

standards in intuitive layout and operation. 

Users are quickly drawn to the large 

on/off button controls with associated 

up/down adjustments. Panels may be 

ordered engraved in up to 10 button 

configurations. There is even a choice of 

button size and colour. 

2 Small 

buttons 

4 Small 

buttons 

6 Small 

buttons 

Ineo control panels can be ganged 

together to meet specific project needs. 

Individual buttons have backlight indicator 

lights and strong tactile feedback. 

Ineo is the clean, elegant, and simple way 

to control lighting on your project. 

1 Large 

button 

2 Large 

buttons 

3 Large 

buttons 

1 Large button 

Raise & Lower 

On / Off 

2 Small buttons 

On / Off 

Raise & Lower 

2 Large button 

Raise & Lower 

On / Off 

4 Small buttons 

On / Off 

Raise & Lower





Toggle on/off 


True off 




Dimensions 




Buttons include scene, raise, lower, on, off 

functionality. 

Choice of large or small button caps 

Standard or custom engraving 

on buttons 

Tap on/off feature to overide fade time 

All plastic construction with a separate 

snap-on surround 

Requires NEMA (US Style) backbox 

3”h x 2”w x 2.5”d 



10 panel variants selectable via 

Source Controller 

Each button individually configurable via 

iCANsoft 

Variable fade times programmable from 

0.1seconds to 60 minutes per button 

Built-in infrared receiver with learnable 

remote codes. 

12Vdc powered direct from 

iCANnet TM network 

Tested to withstand 12kV electro-static 

discharge without damage or 

memory loss. 

Flash memory for future proof 

upgradeability 


Environmental Data 

Temperature Range: 0°C to +40°C 

Humidity: 0% - 95% non condensing 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: INEO Rev7 0115 









Revio 

Revio Control Panel Range 

Key Features 

• Labeling, colour, style, language and 

logos completely customisable 

• Printed inserts easily produced to 

your requirements 



1 Button 2 Button 

4 Button 

Vertical 

4 Button 

Horizontal 

Overview 

Revio is a premier range of lighting control 

panels that combines a simple user 

interface with superb design, and broad 

configurability. 

Lighting level control is combined with a 

simple on/off action in one ergonomically 

simple rotary button control. Separate 

scene or channel/zone buttons are 

activated using advanced capacitive touch 

plates that sit under a clean front surface. 

Standard or user defined inserts enable 

Revio to be adapted for virtually any 

environment and configuration. 

Revio is the only lighting control user 

interface available that allows for simple 

on/off raise lower control, scenes, and 

individual zone control within a single 

gang control. 

6 Button 

4 Scenes & 

4 Zones or 

8 Scenes





Toggle on/off 


True off 




Dimensions 




Polycarbonate cover 

“Clean” switch, when pressed , allows the 

control panel to be wiped clean without 

changing light levels. 

All plastic construction with a separate 

steel chassis that is affixed to wallbox as 

first fix with the unit attaching to chassis 

with screws. 

Requires NEMA (US Style) backbox 

3”h x 2”w x 2.5”d 



Variable fade times programmable from 

0.1seconds to 60 minutes per button. 

12Vdc powered direct from iCAN network 

Tested to withstand 12kV electro-static 

discharge without damage or memory loss. 

Flash memory for future proof 

upgradeability. 

Connects via Cat5 FTP using terminals 



Humidity: 0% - 95% non condensing 





T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: REVIO Rev8 0115 









TSC30 

3.5” LCD Colour Touchscreen 

Key Features 

• 3.5 inch (89mm) diagonal backlit LCD 

screen with analogue touch overlay 

• ¼ VGA 320 x 240 pixel resolution. 

• 65000 Colours available 

• Fits standard double gang backbox 

(35mm Depth) 

• Selection of Bezel finishes with 

screwless fixing 

• Allows the user to easily reprogram 

their own scenes (engineer site vist 

not required) 

• Supplied with basic configuration 

installed 

• Standard buttons and backgrounds 

supplied with configuration software 

• All graphics and buttons can be 

customised 

• Programmable backlight level 

to automatically reduce screen 

brightness to a non-intrusive level 

after time out period 

• Password feature to allow different 

access levels 

• Large memory allows for up to 250 

pages depending of graphics used 



Overview 

The LCD touch screen is a flexible device which provides an intuitive “user 

friendly” method of interfacing to the iLight control system. The LCD touch 

screen provides virtually a limitless flexibility of system configuration and control. 

It is completely software based, and programs can be tailored to suit the precise 

needs of the user. The touch screen can also be used to provide control of other 

integrated systems such as audio, curtains, blinds and heating. 

The TSC30 incorporates fully customisable graphics which allows the user to create 

the exact look and feel of their screen. From a welcome page in a hotel suite that 

includes a background image of the hotel, to a minimalist theme for a home cinema 

room, the LCD touch screen can be tailored for you. A full choice of fascia colours 

and metal finishes coupled with a comprehensive range of graphic ‘themes’ within 

the software library allow the touch screen to blend into it’s environment.

‘User Friendly’ Software 

Screen design and customisation is achieved using 

iLight’s bespoke software iCANsoft. iCANsoft 

incorporates a design mode which allows easy 

manipulation of each individual page. 

Background images can be quickly applied using the 

browse function and virtual buttons positioned at any 

point with a simple ‘drag & drop’ action. Buttons can 

also be animated, producing a ‘press in & out’ effect. By 

applying a different appearance to the button, they can 

be used to show when a function has been activated. 

Mechanical 

Climate Range: 




One set of terminals for iLight network 


Memory: 

FLASH memory to be able to upgrade firmware 

250 Page Memory - Depending on graphics used 

Includes RJ12 Programming Point 

Functionality 

Scene Selection 

Scene programming 

Channel level indicated with bar graphs and percentage. 

Scene and channel naming 

Task / sequence programming 

Default screen programming 

Photocell / motion sensor interaction 

Ability to import room layout drawings, customer logos 

& graphics 

Ability to insert soft buttons for activating scenes and / or 

channels. 

Dimensions 

Electrical 

Supply: 9VDC 1 Amp via included power supply 

Termination 

Rising clamp screw terminals within two part connectors, able to 

accept 1.5mm 2 stranded and solid wire. 

iCANnet TM network: Screw terminals within two part connectors, 

able to accept 1.5mm 2 stranded and solid wire. 

Programming: iCANsoft configuration software, via USB. 

Diagnostics - network 

Memory: 


EEPROM for 128 scene memory 

Typical Schematic 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: TSC30 Rev9 0115 









TSC50 

5.7” LCD Colour Touchscreen 

Key Features 

• 5.7 inch (145mm) diagonal backlit LCD 

screen with analogue touch overlay 

• ¼ VGA 320 x 240 pixel resolution 

• 65000 Colours available 

• Selection of Bezel finishes with 

screwless fixing 

• Allows the user to easily reprogram 

their own scenes (engineer site vist 

not required) 

• Supplied with basic configuration 

installed 

• Standard buttons and backgrounds 

supplied with configuration software 

• All graphics and buttons can be 

customised 

• Programmable backlight level 

to automatically reduce screen 

brightness to a non-intrusive level 

after time out period 

• Password feature to allow different 

access levels 

• Large memory allows for up to 250 

pages depending of graphics used 



Overview 

The LCD touch screen is a flexible device which provides an intuitive “user 

friendly” method of interfacing to the iLight control system. The LCD touch 

screen provides virtually a limitless flexibility of system configuration and control. 

It is completely software based, and programs can be tailored to suit the precise 

needs of the user. The touch screen can also be used to provide control of other 

integrated systems such as audio, curtains, blinds and heating.

‘User Friendly’ Software 

Screen design and customisation is achieved using 

iLight’s bespoke software iCANsoft. iCANsoft 

incorporates a design mode which allows easy 

manipulation of each individual page. 

Background images can be quickly applied using the 

browse function and virtual buttons positioned at any 

point with a simple ‘drag & drop’ action. Buttons can 

also be animated, producing a ‘press in & out’ effect. By 

applying a different appearance to the button, they can 

be used to show when a function has been activated. 

Mechanical 





One set of terminals for iLight network 


Memory: 


250 Page Memory - Depending on graphics used 

Includes RJ12 Programming Point 

Functionality 

Scene Selection 


Channel level indicated with bar graphs and percentage. 



Default screen programming 


Ability to import room layout drawings, customer logos 

& graphics 

Ability to insert soft buttons for activating scenes and / or 

channels. 

Electrical 

Supply: 12VDC 1 Amp via included power supply 

Termination 

Rising clamp screw terminals within two part connectors, able to 

accept 1.5mm 2 stranded and solid wire. 

iCANnet TM network: Screw terminals within two part connectors, 


Programming: iCANsoft configuration software, via USB. 


Dimensions 





T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: TSC50 Rev9 0115 








Network Interfaces 

Mobile Applications 

iCANnet TM control using iPhone®, iPod touch®, iPad® 

Key Features 

• Mobile user interface for controlling iLight’s 

iCANnet TM lighting network. 

• Bi-directional control and feedback. 

• Supports multiple iPhone®, 

iPod touch®, iPad® devices on same network. 

• Automatically loads room and scene information 

when connected. 

• Selective password protection. 

• Adjust and save changes. 

• Customisable background images. 

• Intuitive fader and switch icons. 

Overview 

iLight mobile applications for iPhone®, iPod touch®, iPad® now bring 

fast and intuitive control of a complete lighting system to a hand 

held device. Navigate floors and rooms to choose, adjust and save 

lighting scenes with simple touch control operation. 

Mobile applications must be used in conjunction with iLight EG2 and 

EG2-NA Ethernet Gateway devices for network access. 

At turn on, the network will recognise each mobile device and 

auto populate with the latest layout, scene and level settings for 

immediate use. Networks require initial commissioning and setup. 

Installations may support multiple devices and varying security levels 

permitting only authorised user to make alterations. 

Screen views can be personalised with custom background images 

via the mobile device. Area, room and floor labels may be individually 

tailored for the installation at setup. 

Application includes demo program to preview and learn operational 

capabilities prior to commissioning.

Application Download 

iOS for iPhone®/ iPod touch®/ iPad® 

http://www.apple.com/itunes 

Residential Applications include: 

Private Homes 

Apartments 

Home Cinemas 

Hotel Suites 

Smarthomes 

Commercial Applications include: 

Meeting Rooms 

Hotel Ball Rooms 

Board Rooms 

Lecture Theatres 

Leisure and Restaurant Chains 

Idea fo extending existing mobile devices 

to control lighting. 

Ideal hand held device for maintenance or operational 

adjustment not requiring a service engineer. 

Application requires installation of Ethernet Gateway providing a connection between iLight’s 

iCANnet TM network and an Ethernet LAN 

Available in two versions: 

EG2-NA - Ethernet Gateway including power supply and steel enclosure. 

EG2 - Ethernet Gateway in DINrail enclosure. Power Supply and metal DINRail enclosure available 

to order separately. 





T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: Mobile Apps Rev3 0115 








iLight Source Controllers 

SCLED0405 

4 Channel x 5 Amp Leading & Trailing Edge Source Controller 

Key Features 

• Leading and Trailing edge compatible 

• No minimum load 

• Silent operation 

• 4 x 5 Amp rated source controller 

• Electronic overload protection 

• 128 scene memory 

• Multiple choices of circuit protection 

• Security door for MCBs 

• Optional RCBO per channel 

• Fail to full safety feature 

• iCANnet TM network inputs 

• Audio Visual Port (RS485) 

• Panic/Fire alarm input 

• Emergency Lighting Terminals 





Overview 

Designed to cope with today’s complex loads, 

SCLED is ideal for dimmable mains powered 

LED, LED drivers, tungsten halogen as well 

as low voltage electronic transformers (not 

wirewound transformers). 

Tested for compatibility with a wide range of 

LED lamps, configurable channel by channel 

for Leading or Trailing Edge operation. SCLED 

is ideal where silent operation is required as 

well as providing reliable service over many 

years. With a 128 scene integral memory, this 

device offers multiple control options, to meet 

the most demanding specifications. 

In addition to iLight’s iCANnet TM network 

connectivity, it also has an audio visual port 

(optionally a DMX port), and panic/fire alarm 

input. It is typically used on its own in areas 

that need manageable and controlled light 

such as themed restaurants, visitor centres, 

art galleries, and churches, or as part of a 

comprehensive network in large building 

complexes.

Mechanical 

Weight: 4kg (RCBO, RCBOX versions - 4.5kg) 

Mains Cable Access: 

4 x 22.5mm/PG16 knockouts, 4 x 25.5mm/M25 knockout & 

1 x 28.5mm/PG21 knockout 


1 x 22.5mm/PG16 knockout & 1 x 25.5mm/M25 knockout 

Climate Range 



IP Rating: IP20 

Control Inputs 

Two sets of terminals for the iCANnet TM network 


One RJ12 socket for programming the iCANnet TM network 

One set of terminals for the Audio Visual Port, RS485 

One set of terminals for the panic/fire alarm input 

Dimensions 

Electrical 

Maximum Load: 20 Amp single phase @ 40ºc 

Maximum Channel Current: 5 Amps resistive. For LED and LED 

drivers, de-rate according to LED manufacturers guidelines. 

Supply: 230 volts -/+ 10% 50/60 Hz (optionally, 127 volt 60 Hz) 

Protection: 4 x 6 amp MCBs Type C, 6KA rated, Input isolator. 

Options: 

SCLED0405S - Single pole, no isolator 

SCLED0405N - Neutral disconnect, no isolator 

SCLED0405D - Double pole, no isolator 

SCLED0405RCBO - RCBO Breakers with isolator 

SCLED0405RCBOX - As SCT0405S with isolator (For field fit of RCBOs) 

Load Types: 

Dimmable mains powered LED, LED drivers, tungsten halogen & 

low voltage electronic transformers 

(Check the iLight help desk for details) 

Not suitable for magnetic transformers or metal halide type loads. 

Minimum Load: No Minimum Load 

Dimmed Outputs: 4 x 5Amp 

Switched Outputs: 

The Dimmed outputs may be configured to switch, for 

non-dimmed loads. (Check the iLight help desk for details) 

Note: Always follow lamp manufacturer’s recommendation on 

Leading and Trailing Edge dimming, de-rating and maximum 

loading on each channel. Capacitive loads including mains 

dimmable LED may require de-rating. 


Incoming supply, max’ cable size: 10mm 2 

Loads, max’ cable size: 1 x 4mm 2 or 2 x 2.5mm 2 per circuit 


Audio Visual Port: RS485 2 x 1mm 2 

Auxiliary over-ride input: 2 x 1mm 2 

Memory: 



Fade Times: 0.1 seconds to 60 minutes 

Other transistor source controllers: see SCLED1205, SCA1210, 

SCA0410, SCMA0402 (DINrail mounted) 


SCI0405 D version - 400x220x155mm. 

RCBO & RCBOX version - 340x255x155mm. 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: SCLED0405 Rev3 0115 









SCLED1205 

12 Channel x 5 Amp Leading & Trailing Edge Source Controller 

Key Features 

• Leading and Trailing edge compatible 

• No minimum load 

• Silent operation 


• Electronic overload protection 


• Multiple choice of circuit protection 





• DMX input option 








Overview 

Designed to cope with today’s complex loads, 

SCLED is ideal for dimmable mains powered 

LED, LED drivers, tungsten halogen as well 

as low voltage electronic transformers (not 

wirewound transformers). 

Tested for compatibility with a wide range of 

LED lamps, configurable channel by channel for 

Leading or Trailing Edge operation. SCLED is 

ideal where silent operation is required as well 

as providing reliable service over many years. 

With a 128 scene integral memory, this device 

offers multiple control options, to meet the most 

demanding specifications. 


connectivity, it also has an audio visual port 

(optionally a DMX port), and panic/fire alarm 

input. It is typically used on its own in areas that 

need manageable and controlled light such as 

themed restaurants, visitor centres, art galleries, 

and churches, or as part of a comprehensive 

network in large building complexes.

Mechanical 

Weight: 10kg (RCBO & RCBOX - 11.5kg) 


12 x 25.5mm and 1 x 38mm knockouts 

Control Cable Access: 1 x 25.5mm knockout 

Climate Range 









Dimensions 

Electrical 


Maximum Channel Current: 5 Amps resistive. For LED and LED 

drivers, de-rate according to LED manufacturers guidelines. 



Options: 

SCLED1205S - Single pole with isolator 

SCLED1205N - Neutral disconnect with isolator 

SCLED1205D - Double pole, no isolator 

SCLED1205RCBO - RCBO Breakers with isolator 

SCLED1205RCBOX - 12 x SP MCBs with isolator (For field fit of RCBOs) 

Load Types: 

Dimmable mains powered LED, LED drivers, tungsten halogen & 

low voltage electronic transformers 

(Check the iLight help desk for details) 

Not suitable for magnetic transformers or metal halide type loads. 

Minimum Load: No Minimum Load 

Dimmed Outputs: 12 x 5Amp 


The Dimmed outputs may be configured as switches, for nondimmed 

loads. They require a minimum load of 30mA for them to 

latch. Before connecting discharge lamps, consult iLight. 







Memory: 




Mains Stabilisation: 50:1 

Other transistor source controllers: see SCLED0405, SCA1210, 

SCA0410, SCMA0402 (DINrail mounted) 

SCLED1205 D version - 690x220x155mm. 



iCANnet TM 

(CAT5-FTP) 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: SCLED1205 Rev3 0115 









SCI0110T 

1 Channel, 10 Amp Inductive Source Controller 

Key Features 

• 1 x 10 Amp programmable 

inductive source controller 

module 


• Suitable for 10 Amp single 

phase supply 




• Panic/fire alarm input 

• Future proof with FLASH 

memory 


standards 

• Designed and manufactured 

to IS09001:2008 standards 

Overview 

This 1 x 10 amp source controller is designed 

to provide scene set dimming of lighting. It is 

suitable for resistive and inductive loads. 

In addition to the iLight iCANnet TM network 

connectivity, it also has an audio visual port and 

a panic/fire alarm input. It can be used on its 

own in single channel applications, or as part 

of a comprehensive network in large building 

complexes.

Mechanical 

Weight: 2.5kg 


2 x 25.5mm and 2 x PG16 knockouts 


1 x 25.5mm and 1 x PG16 knockout 










Dimensions 

Electrical 


Maximum Channel Current: 10 Amp 


Protection:Requires external circuit breaker 

Load Types: 

Incandescent 230 volt lamps 

Low voltage inductive lamps (wire wound or electronic) 

Cold cathode (Check the iLight help desk for details) 

Minimum Load: 20 watts 






Panic/fire alarm input: 2 x 1mm 2 

Memory: 

FLASH memory to be able to upgrade software 




Other Inductive Source Controllers: SCI0405, SCI0410, SCI0420, 

SCI1205, SCI1210, SCI1220 and the SCMI0402 





T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: SCI0110T Rev5 1214 









SCI0405 

4 Channel x 5 Amp Inductive Lighting Source Controller 

Key Features 


• Dims resistive, inductive and low 

voltage electronic transformer loads 

(that are compatible with leading edge 

dimmers) 

• Quiet operation 






• iLight network inputs 









Overview 

This 4 circuit economy source controller 

is fully rated for 4 x 5 Amps of continuous 

inductive or resistive lighting loads. Whether 

used for tungsten, low voltage or cold 

cathode light sources, this unit will provide 

reliable service over many years. With a 128 

scene integral memory, this device offers 

multiple control options, to meet the most 


In addition to the iLight network 

connectivity, it also has an audio visual port, 

and panic/fire alarm input. It is typically used 

on its own in areas that need manageable 

and controlled light such as themed 

restaurants, visitor centres, art galleries, and 

churches, or as part of a comprehensive 


Mechanical 

Weight: 4kg (4.5kg for RCBO & RCBOX versions) 






Climate Range 




Two sets of terminals for the iLight network 


One RJ12 socket for programming the iLight network 



Dimensions 


Electrical 


Maximum Channel Current: 5 Amps 



Options: 

SCI0405S - Single pole, no isolator 

SCI0405N - Neutral disconnect, no isolator 

SCI0405D - Double pole, no isolator 

SCI0405RCBO - RCBO Breakers with isolator 

SCI0405RCBOX - 4 x SP MCBs with isolator (For field fit of RCBOs) 

Load Types: 

Incandescent 230 volt lamp 

Inductive Wire wound (allow for 10% transformer losses) 

Leading edge electronic transformers 


Minimum Load: 20 watts inductive load per channel 

Dimmed Outputs: 4 x 40 Amp Triacs 








iLight network cable size: 5 x 1mm 2 



Memory: 





Other inductive source controllers: SCI0410, SCI0420, SCI0805, 


Notes: Where control of Electronic transformers for trailing edge 

dimming is required, refer to the iLight SCA and SCLED Source 

Controllers. 






T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: SCI0405 Rev5 0614 









SCI0410 


Key Features 

• 4 x 10 Amp fully rated source controller 




dimmers) 
















Overview 

This 4 circuit robust source controller is 

fully rated for 4 x 10 Amp of continuous 

inductive lighting loads. Whether used 

for tungsten, low voltage or cold cathode 

light sources, this unit will provide reliable 

service over many years. With a 128 




In addition to the iLight connectivity, it also 

has an audio visual port, and panic/fire alarm 

input. It is typically used on its own in small 

areas that need manageable and controlled 

light such as board rooms, restaurants 

and lecture theatres, or as part of a 


complexes.

Mechanical 

Weight: 7kg (8kg for D, RCBO & RCBOX versions) 


4 x 25mm, 4 x PG16 and 1 x PG 21 knockouts 


1 x 25mm and 1 x PG16 knockouts 

Climate Range 









Dimensions 

Electrical 




Protection: 10 amp MCBs Type C, 6KA rated 

Options 

SCIO410S - Single pole, no isolator 

SCIO410N - Neutral disconnect, no isolator 

SCIO410D - Double pole, no isolator 


SCI0410RCBOX - As SCI0410S with isolator (For field fit of RCBOs) 

Load Types: 





Minimum Load: 20 watts per channel 



The Dimmed outputs may be configured as switches, for 

non-dimmed loads. They require a minimum load of 30mA for 

them to latch. Before connecting discharge lamps, consult the 

iLight help desk. 







Memory: 






SCI1210, SCI1220 and the SCMI0402 





T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 











SCI0420 


Key Features 





dimmers) 
















Overview 

This 4 circuit robust source controller is 

fully rated for 4 x 20 Amp of continuous 

inductive lighting loads. Whether used 

for tungsten, low voltage or cold cathode 


service over many years. With a 128 






and panic/fire alarm input. It is typically 

used on its own in small areas that need 

manageable and controlled light such 

as board rooms, restaurants and lecture 

theatres, or as part of a comprehensive 


Mechanical 

Weight: 9kg (12kg for D version) 


4 x 25mm, 4 x PG16 and 1 x PG 21 knockouts 



Climate Range 









Dimensions 


RCBO & RCBOX version - Consult iLight. 

Electrical 





Options 



SCIO420D - Double pole, no isolator 

SCI0420RCBO - Consult iLight 

SCI0420RCBOX - Consult iLight 

Load Types: 








The Dimmed outputs may be configured as switches, for 

non-dimmed loads. They require a minimum load of 30mA for 

them to latch. Before connecting discharge lamps, consult the 








Memory: 











T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 











SCI1205 


Key Features 


• Dims resistive, inductive and low voltage 

electronic transformer loads (that are 

compatible with leading edge dimmers) 
















Overview 

This 12 circuit economy source controller 

is fully rated for 12 x 5 Amps of continuous 

inductive or resistive lighting loads. Whether 

used for tungsten, low voltage or cold cathode 


service over many years. With a 128 scene 

integral memory, this device offers multiple 

control options, to meet the most demanding 

specifications. 



and panic/fire alarm input. It is typically used 

on its own in areas that need manageable and 

controlled light such as themed restaurants, 

visitor centres, art galleries, and churches, or 

as part of a comprehensive network in large 

building complexes.

Mechanical 

Weight: 10kg 




Climate Range 









Electrical 





Options: 

SCI1205S - Single pole with isolator 

SCI1205N - Neutral disconnect with isolator 



SCI1205RCBOX - 12 x SP MCBs with isolator(For field fit of RCBOs) 

Load Types: 











Dimensions 







Memory: 










iCANnet TM 

(CAT5-FTP) 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 











SCI1210 


Key Features 














• Temperature Monitoring 







Overview 

This 12 channel unit provides comprehensive 

features and performance at at truly competitive 

price. It is fully rated for 40 Amps three phase 

of continuous inductive lighting load. Whether 





control options to meet the most demanding 


With iLight’s iCANnet TM network connectivity, it 

has the capability of being linked with a virtually 

limitless number of other iLight products to 

build up to any size of system. This product is 

designed for projects where there are multiple 

channels of Architectural lighting. It is the 

perfect choice for hotel ballrooms, atria and 

large themed restaurants and museums. With 

an optional DMX512 control input, it is a highly 

adaptable product.

Mechanical 

Weight: 18kg 

(Double Pole version: 19.5kg RCBO & RCBOX version: 20kg) 







Temperature Monitor: This unit is complete with thermal 

monitoring. Should it over-heat the unit will automatically 

switch off 







Optional: DMX512 input card (add X to the end of the part 

number) 

Dimensions 

Electrical 

Maximum Load: 40 Amp three phase @ 40ºc 


Supply: 415/230 volts -/+ 10% 50/60 Hz 

(optionally, 220/127 volt 60 Hz) 


Options: 






Load Types: 












Incoming supply, max’ cable size: 10mm 2 live, 16mm 2 neutral 





Memory: 








RCBO & RCBOX version: 850 (h) x 374 (w) x 155mm (d) 

iCANnet TM 

(CAT5-FTP) 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 











SCI1220 


Key Features 














• Temperature Monitoring 







Overview 

This 12 channel unit provides comprehensive 

features and performance at at truly competitive 

price. It is fully rated for 80 Amps three phase 

of continuous inductive lighting load. Whether 












channels of Architectural lighting. It is the 

perfect choice for hotel ballrooms, atria and 

large themed restaurants and museums. With 

an optional DMX512 control input, it is a highly 

adaptable product.

Mechanical 

Weight: 22kg 

(Double Pole version: 23.5kg RCBO & RCBOX version: 24kg) 







Temperature Monitor: This unit is complete with thermal 

monitoring. Should it over-heat the unit will automatically 

switch off 








number) 

Dimensions 

Electrical 






Options: 






Load Types: 












Incoming supply, max’ cable size: 10mm 2 live, 16mm 2 neutral 





Memory: 








RCBO & RCBOX version: 850 (h) x 374 (w) x 155mm (d) 

iCANnet TM 

(CAT5-FTP) 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 











SCI0805 

8 Channel Combined HF, Switching and Inductive Source Controller 

Key Features 

• 40 Amp total box load 

• 1-10 volt, DSI and DALI ballasts 














Overview 

This cost effective compact source 

controller is an 8 channel device that 

provides 4 x 5Amps inductive dimmed 

circuits and 4 x 5Amp relay outputs. Relay 

outputs can be configured to control 1-10 

volt, Tridonic DSI or Broadcast DALI. 


connectivity, it also has an audio visual port. 

It is suitable for controlling 1-10V, DSI and 

broadcast DALI lighting and non lighting 

loads. It is typically used on its own in 

small areas of mixed lighting sources that 

need manageable and controlled light and 

non-dim circuits, such as video conference 

rooms, meeting rooms, board rooms, hotel 

suites, private residences, or as part of a 


complexes.

Mechanical 

Weight: 7kg (8kg for RCBO & RCBOX versions) 


4 x 25.5mm, 4 x PG16 and 1 x PG 21 knockouts 



Climate Range 









Dimensions 

SCI0805 RCBO & RCBOX version - 440 x 255 x 155mm 

Electrical 




Protection: 8 x 6 Amp MCBs Type C, 6KA rated 

Options 

SCIO805T - 2 x 20A Breakers, no isolator 

SCIO805TN - 2 x 20A ‘N’ Type Breakers, no isolator 



SCIO805RCBO - RCBO Breakers with isolator 

SCIO805RCBOX - 8 x SP MCBs with isolator (For field fitting of RCBOs) 

Load Types: 

1-10 volts HF Fluorescent, 100 per channel 

Tridonic DSI HF Fluorescent Ballast, 32 per channel, max 128 per unit. 

Broadcast DALI HF Fluorescent Ballast, 32 per channel, max 128 per 

unit. 

4 x 5 Amp incandescent or inductive (not suitable for trailing edge 

capacitive loads) 

Dimmed Outputs: 

4 x 5 Amp inductive 

4 x 5Amp relays for controlling either 1-10V, Tridonic DSI or 

Broadcast DALI 


4 x 230v 5 Amp (inductive or resistive) 



Ballast output, max’ cable size: 8 pairs x 2.5mm 2 





Memory: 








T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 











SCA0410 

4 Channel x 10 Amp Adaptive Source Controller 

Key Features 

• 4 x 10 Amp fully rated 

programmable and adaptive 

source controller module 


• Each channel can be set 

for leading or trailing edge 

dimming suitable for resistive, 

inductive and capacitive loads 

• Complete with iProtect 

lamp protection and auto 

short circuit protection 

• Multiple choice of circuit 

protection and security door 

to MCBs 



• iCANnet TM Network inputs 


• Optional: DMX512 input 



standards 


memory 


to ISO9001:2008 standards 

Overview 

This 4 x 10 amp adaptive source controller is 

designed to provide scene set dimming of lighting 

loads that require either leading or trailing edge 

dimming. This FET based adaptive dimmer is 

suitable for resistive, inductive and capacitive loads. 

In the event of reactive loads being detected, it 

uses patented circuitry to protect both itself and the 

connected load. With a 128 scene integral memory 

this device offers multiple control options to meet 


The device is complete with dynamic voltage and 

current monitoring. This facility provides short circuit 

protection, and protects the lamps from thermal 

shock and so extends the lamp life. It is completely 

silent in operating mode when using trailing edge 

dimming. In addition to the network connectivity, 

it also has an audio visual port and auxiliary, as well 

as a DMX512 optional input. The versatility and 

adaptability of this product makes it the perfect 

device for hotel ballrooms, museums, visitor 

centres, entertainment venues, and as part of large 

integrated systems.

Mechanical 

Weight: 9kg 

SCA0410S - Mains Cable Access: 


Control Cable Access: 1 x 25mm knockout 

SCA0410N & SCA0410D - Mains Cable Access: 

4 x PG16 and 1 x PG29 knockouts 

Control Cable Access: 1 x PG16 knockout 




Temperature Monitor: This unit is complete with 

thermal monitoring. Should it over-heat the unit will 

automatically switch off 




One RJ12 socket for programming iCANnet TM network 



Optional: DMX512 input card (add X to the end of the 

part number) 

Dimensions 

Electrical 

Maximum Load: 40 Amp single phase @ 40ºC 


Supply: 415/230 volts -/+ 10% 50/60 Hz (optionally, 220/127 volt 60 Hz) 

Protection: 10 Amp MCBs Type C, 6KA rated plus internal electronic 

short circuit protection, input isolator not included 

Options 

SCA0410S - Single pole 

SCA0410N - Neutral disconnect 

SCA0410D - Double Pole 

SCA0410RCBO - RCBO Breakers 

SCA0410RCBOX - 4 x SP MCB (For field fit of RCBOs) 

Load Types: 


Low voltage inductive lamps (wire wound or electronic) 

Low voltage electronic (capacitive) 



Dimmed Outputs: 2 x 45 Amp FET’s per circuit 


The Dimmed outputs may be configured as switches for non-dimmed 

loads. They require a minimum load of 30mA for them to latch. 

Before connecting discharge lamps, consult the iLight help desk 


Incoming supply, max cable size: 10mm 2 

Loads, max cable size: 1 x 4mm 2 or 2 x 2.5mm 2 per circuit 




Memory 





Other Adaptive Source Controllers: SCA1210 and SCMA0402 


SCA0410 RCBO & RCBOX versions - Consult iLight 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: SCA0410 Rev6 1114 









SCA1210 

12 Channel x 10 Amp Adaptive Source Controller 

Key Features 

• 12 x 10 Amp fully rated 

adaptive source controller 

module 


• Each channel can be set 

for leading or trailing edge 

dimming suitable for resistive, 

inductive and capacitive loads 

• Complete with iProtect 

lamp protection and auto 

short circuit protection 


protection and security door 

to MCBs 



• iLight iCANnet TM network 

inputs 


• Optional: DMX512 input 



standards 


memory 



Overview 

This 12 x 10 amp adaptive source controller is 

designed to provide scene set dimming of lighting 

loads that require either leading or trailing edge 

dimming. This FET based adaptive dimmer is 

suitable for resistive, inductive and capacitive loads. 

In the event of reactive loads being detected, it 

uses patented circuitry to protect both itself and the 

connected load. With a 128 scene integral memory 

this device offers multiple control options to meet 


The device is complete with dynamic voltage and 

current monitoring. This facility provides short 

circuit protection, and protects the lamps from 

thermal shock and so extends the lamp life. It is 

completely silent in operating mode when using 

trailing edge dimming. In addition to the iLight 

network connectivity, it also has an audio visual 

port and auxiliary, as well as a DMX512 optional 

input. The versatility and adaptability of this product 

makes it the perfect device for hotel ballrooms, 

museums, visitor centres, entertainment venues, 

and as part of large integrated systems.

Mechanical 

Weight: 18kg 

UK Version - Mains Cable Access: 


Control Cable Access: 1 x 25mm knockout 

EURO Version - Mains Cable Access: 


Control Cable Access: 1 x PG16 knockout 




Temperature Monitor: This unit is complete with 

thermal monitoring. Should it over-heat the unit will 

automatically switch off 




One RJ12 socket for the programming iCANnet TM 

network 




part number) 

Dimensions 

Electrical 

Maximum Load: 40 Amp three phase @ 40ºC 



Protection: 10 Amp MCBs Type C, 6KA rated plus internal electronic 

short circuit protection. Input isolator not included 

Options 

SCA1210S - Single pole 

SCA1210N - Neutral disconnect 

SCA1210D - Double Pole 

SCA1210RCBO - RCBO Breakers 

SCA1210RCBOX - 12 x SP MCB (For field fit of RCBOs) 

Load Types: 

Incandescent 230 volt lamps, low voltage inductive lamps (wire 

wound or electronic) Low voltage electronic (capacitive), cold cathode 


Dimmed Outputs: 2 x 45 Amp FET’s per circuit 


The Dimmed outputs may be configured as switches for non-dimmed 

loads. They require a minimum load of 30mA for them to latch. 

Before connecting discharge lamps, consult the iLight help desk 







Memory: 





Other Adaptive Source Controllers: SCA0410 and SCMA0402 

Notes: Where control of HF ballasts for fluorescent lighting is 

required. Refer to the SCH0410S, SCH1210S, or SCH1200T. 


SCA1210 RCBO & RCBOX versions - Consult iLight 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: SCA1210 Rev6 1114 









SCH0410 

4 Channel x 10 Amp HF Ballast Source Controller 

Key Features 

• 40 Amp total box load on 

4 circuits 

• 1-10 volt, DSI and DALI 

ballasts 

• 128 Scene Memory 


protection 







• Emergency Lighting 

Terminals 


memory 


standards 



Overview 

This compact HF Ballast controller is a 4 channel 

device that provides 4 switched power circuits 

with 4 channels of scene set dimming for 1-10 

volt, Tridonic DSI or DALI digital HF Fluorescent 

ballasts. Its 10 Amp power relays make it suitable 

for independent non-dimmable loads as well. 


connectivity, it also has an audio visual port. It is 

suitable for controlling other 0-10 volt devices, such 

as a motorised Iris in a projector and 0-10 and DSI 

/ DALI controlled transformers and cold cathode. 

It is typically used on its own in small areas that 

need manageable and controlled light, such as 

meeting rooms, cinema and entrance lobbies, or as 

part of a comprehensive network in large building 

complexes.

Mechanical 

Weight: 4kg 










Two sets of terminals for the iCANnet TM network. 

One RJ12 socket for programming iCANnet TM network 



Dimensions 

Electrical 





Options: 

SCH0410S - Single pole, no isolator 

SCH0410N - Neutral disconnect, no isolator 

SCH0410D - Double Pole, no isolator 

SCH0410RCBO - RCBO Breakers with isolator 

SCH0410RCBOX - As SCH0410S but with isolator (For field fit of RCBOs) 

Load Types: 

1-10 volts HF Fluorescent, 100 per channel. Tridonic DSI HF 

Fluorescent Ballast, 32 per channel. DALI HF Fluorescent Ballast 

(Broadcast mode only), 32 per channel, max 128 per unit. 0-10 volt 

Iris control (20K 0hm input). 

1-10 volt Multi-Load transformers 1000 (Control only) 


4 x 1-10 volts at 0.1 Amp sink current per channel 

4 x Tridonic DSI outputs (uses electronic power switching in ballasts) 

4 x DALI outputs (uses electronic power switching in ballasts) 

The output types above are selectable within iCANedit for each circuit 

Switched Outputs: 4 x 230v 10 Amp (inductive or resistive) 



Ballast output, max cable size: 4 pairs x 2.5mm 2 

Loads, max cable size: 1 x 4mm 2 or 2 x 2.5mm 2 per circuit 




Memory: 




Other HF Ballast controllers: SCH1210, SCH1220, SCMH0410 and 

the SCH1200T 

SCH0410 D versions - 400 x 220 x 155mm 

SCH0410 RCBO & RCBOX versions - 340 x 255 x 155mm 





T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: SCH0410 Rev6 1214 









SCH1200T 

12 Channel HF Ballast Controller 

Key Features 

• 12 channel device 

• DSI and DALI ballasts 

• 1-10 volt (control only) 




inputs 




memory 


standards 



Overview 

This highly cost effective compact source controller 

is a 12 channel device specifically designed for low 

voltage control of fluorescent ballasts. It provides 

12 channels of scene set dimming. This unit may 

also be configured to provide 1-10 volt control for 

analogue devices or DSI or broadcast DALI ballast 

control. 


connectivity, it also has an audio visual port and a 

panic/fire alarm input. It is typically used in open 

plan office areas, or where large numbers of HF 

ballasts are under central control. They can be 

used “stand alone” or as part of a comprehensive 


Mechanical 

Weight: 3kg 




1 x 25mm and 1 x PG16 knockout 








network 



Dimensions 

Electrical 

Maximum Load: There is no load control. Power switching is 

achieved by the DSI / DALI ballasts themselves. 

Maximum Channel Current: Not applicable 

Supply: 1 x 230 volts -/+ 10% 50/60 Hz 

Protection: 20mm fuse 

Load Types: 

Tridonic DSI HF Fluorescent Ballast, 64 per channel, 128 per unit 

DALI HF Fluorescent Ballast (broadcast DALI only), 64 per 

channel, 128 per unit. 

0-10 volt control (20K 0hm input) 

1-10 volt, 100 per channel, 1200 per unit. 


12 x 1-10 volts at 0.1 amp sink current per channel or 12 x 

Tridonic DSI outputs (uses electronic power switching in ballasts) 

or 12 x 0-10 volts output (20mA source max) 

or 12 x DALI outputs (uses electronic power switching in ballasts) 

The output types above are selectable within iCANedit for each 

circuit 

Switched Outputs: None 


Incoming supply, max’ cable size: 2.5mm 2 

Ballast output, max’ cable size: 12 pairs 2.5mm 2 




Memory: 





Other HF Ballast controllers: SCH0410, SCH1210, SCH1220, 

SCMH0410. 





T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: SCH1200T Rev5 1214 









SCH1210 


Key Features 


12 circuits 


ballasts 



protection 








Terminals 


memory 


standards 



Overview 



with 12 channels of scene set dimming for 1-10 

volt, Tridonic DSI or DALI digital HF Fluorescent 

ballasts. Its 10 Amp power relays make it suitable 

for independent non-dimmable loads as well. 





/ DALI controlled transformers, and cold cathode. 

It is typically used on its own in medium to larger 

spaces that need manageable and controlled light, 

such as open plan offices, auditoria circulation 

lobbies, or as part of a comprehensive network in 

large building complexes.

Mechanical 

Weight: 9kg 



Control Cable Access: 1 x 25mm knockouts 






One RJ12 socket for the programming iCANnet TM network 





number) 

Dimensions 

Electrical 





Options 

SCH1210S - Single pole with isolator 

SCH1210N - Neutral disconnect with isolator 



SCH1210RCBOX - 12 x SP MCBs with isolator (For field fit of RCBOs) 

Load Types: 

1-10 volts HF Fluorescent, 100 per channel, 1200 per unit. 

Tridonic DSI HF Fluorescent Ballast, 64 per channel, 128 per unit. 

Broadcast DALI HF Fluorescent Ballast, 64 per channel, 128 per unit. 

0-10 volt Iris control (20K 0hm input) 




12 x Tridonic DSI outputs (uses electronic power switching in 

ballasts) 



circuit 










Memory: 




Other HF Ballast Controllers: SCH0410, SCH1220, SCMH0410 and 

the SCH1200T 

SCH1210 D version - 690x220x155mm. 

RCBO & RCBOX version - 550x255x155mm 





T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 











SCH1220 


Key Features 


12 circuits 


ballasts 



protection 








Terminals 


memory 


standards 



Overview 



with 12 channels of scene set dimming for 

1-10 volt, Tridonic DSI or DALI digital HF 

Fluorescent ballasts. Its 20 Amp power relays make 

it suitable for independent non-dimmable loads 

as well. 





/ DALI controlled transformers and cold cathode. 

It is typically used on its own in medium to larger 

spaces that need manageable and controlled light, 

such as open plan offices, auditoria circulation 

lobbies, or as part of a comprehensive network in 

large building complexes.

Mechanical 

Weight: 9kg 



Control Cable Access: 1 x 25.5mm knockouts 








network 




part number) 

Dimensions 

Electrical 





Options 

SCH1220S - Single pole with isolator 

SCH1220N - Neutral disconnect with isolator 



SCH1220RCBOX - 12 x SP MCBs with isolator (For field fit of 

RCBOs) 

Load Types: 

1-10 volts HF Fluorescent, 100 per channel, 1200 per unit. 

Tridonic DSI HF Fluorescent Ballast, 64 per channel, 128 per unit. 

Broadcast DALI HF Fluorescent Ballast, 64 per channel, 128 per unit. 

0-10 volt Iris control (20K 0hm input) 




12 x Tridonic DSI outputs (uses electronic power switching in 

ballasts) 



circuit 










Memory: 




Other HF Ballast Controllers: SCH0410, SCH1210, SCMH0410 and 

the SCH1200T 

SCH1220 D version - 690x220x155mm. 






T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 











SCS0410 

4 Channel 10 Amp Switched Relay Source Controller 

Key Features 

• 4 x 10 Amp source controller 

• Switches resistive, inductive and 

capacitive lighting loads 


• 128 scene memory. 











• CE compliant to all revelant standards 


ISO9001-2008 standards 

Overview 

This 4 channel high powered intelligent 

switching unit provides outstanding features 

and performance at a truly competitive 

price. It is rated for 40 Amps single phase 

of continuous inductive lighting load. This 

unit is designed for switching large lighting 

loads of most types. With a 128 scene 

integral memory this device offers multiple 



With iLight’s iCANnet TM network connectivity, 

it has the capability of being linked with 

a virtually limitless number of other iLight 

products to build up to any size of system. 

This product is designed for projects where 

there are multiple channels of Architectural 

lighting. It is the perfect choice for shopping 

malls, atria exterior lighting and industrial 

areas.

Mechanical 

Weight: 4kg (D, RCBO & RCBOX - 5kg) 

Mains Cable Access: 4 x 25.5mm, 


Control Cable Access: 1 x 25mm and 1 x PG16 knockout 










Dimensions 

Electrical 



Supply: 230 volts -/+ 10% 50/60 Hz 

(optionally, 127 volt 60 Hz special order) 

Protection: 10 Amp MCBs Type C, 6KA rated 

Options: 

SCS0410S - Single pole, no isolator 

SCS0410N - Neutral, no isolator 

SCS0410D - Double Pole, no isolator 

SCS0410RCBO - RCBO Breakers with isolator 

SCS0410RCBOX - 4 x SP MCBs with isolator (For field fit of RCBOs) 

Load Types: 

This unit is designed to work with most lighting load types. Please 

consult with the iLight help desk for guidance on true load 

calculations. Care should be taken when specifying discharge 

lighting sources with power factor capacitors 


This device uses 4 x 230 volt 10A (Resistive and Inductive) 







Memory: 



Other Switched Relay Controllers: SCS0420, SCS1210, SCS1220, 

SCMS0410 and the SCMS0810. 


SCS0410 D version - 400x220x155mm. 





T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: SCS0410 Rev5 0115 









SCS0420 


Key Features 

• 4 x 20 Amp source controller 




• 128 scene memory. 











• CE compliant to all revelant standards 


ISO9001-2008 standards 

Overview 



and performance at a truly competitive 

price. It is rated for 80 Amps single phase of 

continuous inductive lighting load. This unit 

is designed for switching large lighting loads 

of most types. With a 128 scene integral 

memory this device offers multiple control 

options to meet the most demanding 


With iLight’s iCANnet TM network 

connectivity, it has the capability of being 

linked with a virtually limitless number of 

other iLight products to build up to any size 

of system. This product is designed for 

projects where there are multiple channels 

of Architectural lighting. It is the perfect 

choice for shopping malls, atria exterior 

lighting and industrial areas.

Mechanical 

Weight: 4kg (D, RCBO & RCBOX - 5kg) 

Mains Cable Access: 4 x 25.5mm, 


Control Cable Access: 1 x 25mm and 1 x PG16 knockout 










Dimensions 

Electrical 



Supply: 230 volts -/+ 10% 50/60 Hz 

(optionally, 127 volt 60 Hz special order) 

Protection: 20 Amp MCBs Type C, 6KA rated 

Options: 

SCS0420S - Single pole, no isolator 

SCS0420N - Neutral, no isolator 




Load Types: 






This device uses 4 x 230 volt 20A (Resistive and Inductive) 







Memory: 



Other Switched Relay Controllers: SCS0410, SCS1210, SCS1220, 








T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 











SCS1210 


Key Features 


• Switches resistive, inductive and capacitive 

lighting loads 
















Overview 



and performance at a truly competitive price. 

It is fully rated for 40 Amps three phrase of 

continuous inductive lighting load. This unit is 

designed for switching large lighting loads of 

most types. With a 128 scene integral memory 

this device offers multiple control options to 

meet the most demanding specifications. 






channels of Architectural lighting. It is the perfect 

choice for shopping malls, atria exterior lighting 

and industrial areas.

Mechanical 

Weight: 9kg (D, RCBO & RCBOX - 10.5kg) 













Dimensions 

Electrical 





Protection: 10 Amp MCBs Type C, 6KA rated, Input isolator 

(except D version) 

Options 

SCS1210S - Single pole with isolator 

SCS1210N - Neutral with isolator 




Load Types: 






This device uses 12 x 230 volt 10A (Inductive and Resistive) 







Memory: 



Other Switched Relay controllers: SCS0410, SCS0420, SCS1220, 





iCANnet TM 

(CAT5-FTP) 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 











SCS1220 

12 Channel x 20 Amp Switched Relay Source Controller 

Key Features 

• 12 x 20 Amp source controller - 

Total load per phase 63A 


















Overview 



and performance at a truly competitive price. 

It is fully rated for 63 Amps three phrase of 

continuous inductive lighting load. This unit is 

designed for switching large lighting loads of 

most types. With a 128 scene integral memory 

this device offers multiple control options to 

meet the most demanding specifications. 






channels of Architectural lighting. It is the perfect 

choice for shopping malls, atria exterior lighting 

and industrial areas.

Mechanical 

Weight: 9kg (D, RCBO & RCBOX - 10.5kg) 













Dimensions 

Electrical 





Protection: 20 Amp MCBs Type C, 6KA rated, Input isolator 

(except D version) 

Options 

SCS1220S - Single pole with isolator 

SCS1220N - Neutral with isolator 




Load Types: 






This device uses 12 x 230 volt 20A (Inductive and Resistive) 







Memory: 



Other Switched Relay controllers: SCS0410, SCS0420, SCS1210, 





iCANnet TM 

(CAT5-FTP) 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 











MPM2400 

Master Processor Module DINrail Mount 

Key Features 

• Control unit and power supply for 

iCANdin DINrail mount power 

dimming, switching and HF units 

• Can control up to 24 channels of 

mixed dimming and switching 

• Intelligent controller that can store up 

to 128 lighting scenes 

• Programmed with iCANsoft which 

automatically identifies all switching 

and dimming units connected for 

simple network configuration 

• Connects into iLight iCANnet TM 

network and can be used with 

all standard iLight control panels, 

interfaces, etc. 

• DINrail mount with lugs for wall 

mounting if required 

• Circuit protection installed separately 

as required 




Overview 

This iCANdin Master Processor Module provides both control signals and power 

for iLight’s range of iCANdin DIN rail mount power dimmer and switching units 

(SCM series products). This unit links to these power units with a short serial 

control cable that loops between the power units within the distribution board. 

The controller manages a maximum of 24 channels that can include a mixture of 

SCM series leading edge dimming, power switching or HF controllers. 

The MPM2400 includes a 128 scene integral memory and offers multiple control 

options to meet the most demanding specifications. 

The Controller connects into the iCANnet TM network making it capable of being 

linked with a virtually limitless number of other iLight products to build up to any 

size of system. 

This product is designed for projects where there are multiple channels of 

architectural lighting. It is the perfect choice for applications where lower power 

dimming is required such as residential applications, hotel suites, offices and 

applications requiring power switching.

Mechanical 

Weight: 1 kg 

Operating temperature: +2ºC to +40ºC 

Note: All enclosures must be adequately ventilated 

Max storage temperature: +60ºC 

Humidity: +5 to 95% non-condensing 

Environmental protection: IP20 

Dimensions 

Electrical 

Supply: 1A 230 volts -/+ 10%, 50/60 Hz 

Incoming terminals: max’ cable size: 2.5mm 2 

Supply protection: Provided by installer - Use 6A or less. 

Output: 2 connections for serial link to dimming and switching 

units. 

Compatibility with: 

SCMI0402, 4 x 2A inductive dimmer 

SCMS0410, 4 x 10A relay switching unit 

SCMS0810, 8 x 10A relay switching unit 

SCMH0410, 4 x 10A relay + 4 x 1-10V HF ballast controller 

SCMR0816, 8 x 16A feed through relay unit 

SCMC0410, 4 x 10A change over relay & HF controller 

Note: SCMA and SCMD do not require MPM2400 and sit directly 

on the iCANnet TM network 

Inputs: 

2 x RJ45 for iCANnet TM network 

1 x 5way screw terminal for iCANnet TM network 

Alarm input 


MPM2400 

iCANnet 

iCANdin Link 

DINrail Devices 

SCMH0410 

SCMI0402 

SCMS0810 

SCMR0816 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Doc. No: MPM2400 Rev10 1114 









SCMA0402 

4 Channel x 2.5A Adaptive Dimmer DINrail Mount 

Key Features 

• 4 x 575W adaptive source 

controller 

• DIN rail mount 


voltage electronic transformer 

loads 

• Circuit protection (MCBs) installed 

separately as required but unit 

includes electronic short circuit 

protection and overload protection 

through internal temperature 

measurement 

• iCANnet TM network input 

• LED indication of operating status 


standards 



Overview 

This 4 circuit source controller is fully rated for dimming all conventional types 

of lighting including incandescent lamps, high and voltage halogen lamps and 

low voltage halogen lamps with magnetic and electronic transformers. There 

are 4 separate dimmer inputs and outputs each with a load capacity of 575W. 

The control circuits automatically change over from leading edge to trailing edge 

dimming depending on the load type. 

The SCMA0402 includes a 128 scene integral memory this device offers 

multiple control options to meet the most demanding specifications. The unit 

connects directly into the iCANnet TM network and has the standard scene 

control and configuration features of iLight dimmers. 

With iLight’s iCANnet TM network connectivity, it has the capability of being 

linked with a virtually limitless number of other iLight products to build up 

to any size of system. This product is designed for projects where there are 

multiple channels of architectural lighting.

Mechanical 

Weight: 1 kg 






Dimensions 

Electrical 

Supply: 230 volts -/+ 10%, 50/60 Hz 

Incoming terminals: max. cable size: 2.5mm2 

Supply protection: provided by installer - use 10A or less 

Output channel rating: maximum 575W (2.5A) resistive/inductive/ 

capacitive 

Minimum dimming output load: 5W 

Load terminals: max. cable size: 

1 x 2.5mm 2 or 2 x 1.5mm 2 per circuit 

Dimmers produce heat, use only in well ventilated enclosures 

Notes 

This unit does not require the MPM2400 master processor unit. 





T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Doc. No: SCMA0402 Rev7 0115 









SCMC0410 

Change Over Relay & HF Controller - DINrail Mount 

Key Features 

• 4 x 10A change over relays suitable 

for motor control of curtains & 

blinds. 

• 4 x additional independant low 

voltage outputs suitable for HF 

fluorescent ballast control. 

• Internal mains supply for isolated 

0-10v, 1-10v HF, DSI or Broadcast 

DALI outputs 

• LED Indicators for relay and HF 

output state. 

• DIN rail mount with lugs for wall 



standards 



Overview 

This versatile DINrail mounted multipurpose curtain controller is suitable for 

control of 2 curtain/blind pairs. Alternatively channels may be configured as 

feed through relay or HF control channels. 4 additional low voltage outputs 

are provided that may be individually configured as 0-10v, 1-10v HF, DSI or 

Broadcast DALI outputs. 

The SCMC0410 is an ideal small package solution for use in conference rooms, 

hotel rooms and smart home projects where curtain/blind or screen controls are 

combined with other switched and fluorescent loads. The 4 independent low 

voltage outputs are especially convenient for low voltage control of a variety of 

other devices including LED ballasts. 

The unit is used with an MPM2400 iCANdin master processor module that can 

manage up to 24 channels of varied dimming and switching within a DIN rail 

distribution board. The MPM includes a 128 scene integral memory and offers 

multiple control options to meet the most demanding specifications. The MPM 

connects into the iLight network and links to the SCMC0410 using a short serial 

data cable. 

Using iLight network connectivity, SCMC0410 has the capability of being linked 

with a virtually limitless number of other iLight products to build up to any size of 

system.

Mechanical 

Weight: 1 kg 






Dimensions 

Electrical 


Incoming terminals: max. cable size: 2.5mm 2 

Rating: Maximum 4 x 10 Amp @ 40ºC 

Supply protection: Provided by installer use max 10A MCB (type 

C). Protect all channels individually. 

Output: channel current: maximum 10A resistive load 

maximum 2A inductive motor load. 

Protection: to be provided by installer 

Load types: Capable of switching inductive, resistive and 

capacitive lighting loads as well as many non lighting loads up to 

10A resistive or 2A inductive per channel. 

Please consult with the iLight® help desk for guidance on true 

load calculations. 

Loads terminals: max. cable size: 1 x 2.5mm 2 or 2 x 1.5mm 2 per 

circuit. 

Dimmed outputs: low voltage outputs channels 5-8 may be 

individually configured as 0-10v, 1-10v, DSI or DALI(broadcast) via 

iCANsoft. 


MPM2400 

iCANnet 

iCANdin Link 


SCMH0410 

SCMI0402 

SCMS0810 

SCMR0816 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Doc. No: SCMC0410 Rev6 0115 









SCMD6400 

16 Group Addressable DALI Controller - DIN Rail mount 

Key Features 

• DALI controller – can dim, switch and 

monitor up to 64 DALI ballasts within 16 

groups 

• Full flexibility for software reconfiguration 

including multiple controllers to match 

changes in physical office layout 

• Includes ability to control and test 

emergency fittings equiped with suitable 

DALI controllers 

• DINrail mount with lugs for wall mounting if 

required 

• 3 RJ12 connectors for sensors each 

configurable for two motion sensor inputs 

or one combined motion and photoelectric 

sensor input 

• Screw terminal connections for up to four 

inputs (allowing 2 retractive switch inputs) 

• Single switched mains output 

• Connects to the iCANnet TM network allowing 

control of lighting from any control panel, 

switch or sensor on the network 

• LEDs display unit status 




Overview 

This fully addressable DALI controller enables control of up to 64 

DALI addresses using up to 16 groups. The system can monitor 

tube life which enables predictive maintenance to be carried out, 

and also monitors lamp function indicating failures, allowing tubes 

to be changed with minimum disruption. 

Lamps can be switched off at the ballast by the DALI controller, 

enabling power wiring schemes to be independent of the 

controller to be used. The SCMD6400 unit contains a single 16 

amp switched supply which can be used to provide power the 

lamps being controlled, enabling the ballasts to be switched off, 

achieving additional energy saving. 

With sensor and switch inputs directly into the unit, it can be used 

as an independent controller. Additional switches and sensors 

can be connected into iLight’s iCANnet TM network using iLight’s 

universal interfaces, creating desired lighting control schemes. 

With iCANnet TM connectivity, it has the capability of being linked 

with a virtually limitless number of other iLight products to build 

up to any size of system.

Mechanical 

Weight: 1 kg 






Dimensions 

Electrical 


Terminals max. wire size: 2.5mm 2 

Sensor inputs: 3 x RJ12 

Switch inputs: 4, configurable as break or make, max wire size 

2.5mm 2 

iCANnet TM network inputs/output: 2 x RJ45 

DALI output screw terminals: Max wire size 2.5mm 2 

DALI signal: Nominal 16V, max current 180mA 

Switched Outputs: 1 x 16A 

Maximum load: 16 Amp single phase @ 40ºC 

Terminals max wire size: 1 x 2.5mm 2 or 2 x 1.5mm 2 per circuit 

Protection: Provided by installer - Use supply MCB, 16A or less 





T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: SCMD6400 Rev10 1014 









SCMH0410 

4 Channel HF Ballast Controller & Power Switcher - DINrail Mount 

Key Features 

• 4 x 10 Amp source controller with 

four 1-10 volt or DSI control outputs 

• 16 Amp total load over 4 circuits 







as required 


standards 



Overview 

This compact HF Ballast controller is a 4 channel unit that provides 4 switched 

power circuits with 4 channels of scene set dimming for 1-10 volt, DSI, or 

broadcast DALI digital HF Fluorescent ballasts. Its 10 Amp power relays also 

make it suitable for independent non-dimmable loads. 

The unit is rated for 16 amps single phase of continuous inductive lighting load. 

This unit is designed for switching lighting loads of most types. 


manage up to 24 channels of varied dimming and switching within a DINrail 

distribution board. The MPM includes a 128 scene integral memory this device 

offers multiple control options to meet the most demanding specifications. The 

MPM connects into the iLight network and links to the iCANdin dimming and 

switching units with a short serial data cable within the distribution board. 

With the iLight network connectivity, it has the capability of being linked with 

a virtually limitless number of other iLight products to build up to any size of 

system. This product is designed for projects where there are multiple channels 

of architectural lighting.

Mechanical 

Weight: 1 kg 






Dimensions 

Electrical 



Rating: maximum 16 Amp single phase @ 40ºC 

Output channel current: Maximum load 10 Amp. 

Minimum load: 0W 

Protection: Provided by installer - use 16A or less. 

Load types: 1-10 volts Ballasts, 100 per channel, Tridonic DSI 

Ballasts, 10 per channel, DALI HF Ballasts (broadcast mode) 

10 per channel & 0-10V controlled loads at 100mA sink or 20mA 

source per channel. The output type is selectable per circuit 

Switched Outputs: 4 x 230v 10 Amp (inductive or resistive) 



Loads, max’ cable size: 1 x 2.5mm 2 or 2 x 1.5mm 2 per circuit 


MPM2400 

iCANnet 

iCANdin Link 


SCMH0410 

SCMI0402 

SCMS0810 

SCMR0816 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Doc. No: SCMH0410 Rev7 0115 









SCMI0402 

4 Channel x 500W Dimmer - DINrail Mount 

Key Features 

• 4 x 500W source controller 





(that are compatible with leading 

edge dimming loads) 



as required 


standards 



Overview 

This 4 circuit source controller is fully rated for dimming loads of up to 4 x 500W 

of continuous inductive lighting loads. Whether used for tungsten, low voltage 

or for cold cathode light sources, this unit will provide reliable service over many 

years. 






switching units with a short serial data cable within the distribution board 




of Architectural lighting. It is the perfect choice for shopping malls, atria exterior 

lighting and industrial areas.

Mechanical 

Weight: 1 kg 






Dimensions 

Electrical 



Rating: Maximum 5 Amp single phase @ 40ºC 


Protection: Provided by installer - use 5A or less. 

Output: channel current: Maximum 500W per heatsink 

Load types: this unit is designed to work with incandescent 230 

volt lamps, inductive wire would transformers (allow for 20% 

transformer losses), leading edge electronic transformers and 

cold cathode lamps (please consult with the iLight® help desk for 

guidance on true load calculations) 


circuit. 

Dimmed outputs: the dimmed outputs can be configured as 

switches for non-dimmed loads. They require a minimum load of 

30mA to latch. Before connecting discharge lamps consult the 


Note: Dimmers produce heat, always ensure adequate ventilation 


MPM2400 

iCANnet 

iCANdin Link 


SCMH0410 

SCMI0402 

SCMS0810 

SCMR0816 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Doc. No: SCMI0402 Rev8 0115 









SCMR0816 

8 Channel x 16 Amp Feed Through Relay Controller - DINrail Mount 

Key Features 

• 8 x 16 Amp 

• Mounts to standard Top Hat (TS35) 

DIN rail 



• Build in propogation delay in 

switching sequence 1-8 

• Manual override of any channel 

• Any phase on any input 


standards 



Overview 

This 8 channel 16 amp feed through relay unit provides outstanding features and 

performance at a truly competitive price. Each channel is rated for a total of 

16 amps single phase and is designed to sit on load lines to switch heavy loads 

of all types. 



distribution board. The MPM includes a 128 scene integral memory and offers 

multiple control options to meet the most demanding specifications. The MPM 

connects into the iLight network and links to the iCANdin dimming and switching 

units with a short serial data cable within the distribution board. 



system. This product is designed for projects where high power switching is 

required such as metal halide and high pressure sodium lamps as well as nonlighting 

loads of any voltage up to 230VAC

Mechanical 

Weight: 1 kg 






Dimensions 

Electrical 

Control: 12V via Slave link from Master Controller (MPM2400) 

Rating: maximum 8 x 16 Amp @ 40ºC 

Input channel current: Maximum 16A incoming load 

Output channel current: Maximum load 16 Amp 


Supply Protection: Provided by installer use 16A (type C or faster) 

per channel or less (Protect all channels individually) 

Load types: Capable of switching inductive, resistive and 

capacitive lighting loads as well as many non lighting loads up to 

16A per channel. Please consult with the iLight® help desk for 

guidance on true load calculations. Care should be taken when 

specifying discharge lighting sources with power factor capacitors 

Switched Outputs: this device uses 8 x 230 volt 16A relays 

Loads terminals: max. cable size: 1 x 4mm 2 or 2 x 1.5mm 2 per 

circuit 

Other Switched Relay Controllers: 

SCMS0410, SCMS0810, SCS1210 and SCS1220 


MPM2400 

iCANnet 

iCANdin Link 


SCMH0410 

SCMI0402 

SCMS0810 

SCMR0816 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Doc. No: SCMR0816 Rev5 0115 









SCMS0410 

4 Channel x 10 Amp Switching Controller - DINrail Mount 

Key Features 

• 4 x 10 Amp switching source 

controller 







as required 


standards 



Overview 

This 4 channel 10 amp switching unit provides outstanding features and 

performance at a truly competitive price. It is rated at a maximum total load of 16 

amps single phase of continuous inductive lighting load. This unit is designed for 

switching lighting loads of most types. The unit is also available in an 8 channel x 

10 Amp version (SCMS0810). 











Mechanical 

Weight: 1 kg 






Dimensions 

Electrical 




Output channel current: Maximum 10 Amp 


Supply Protection: Provided by installer use 16A or less 

Load types: this unit is designed to work with most lighting load 

types. Please consult with the iLight® help desk for guidance 

on true load calculations. Care should be taken when specifying 

discharge lighting sources with power factor capacitors 


(Resistive and Inductive) 


circuit 


SCMS0810, SCS0410, SCS0420, SCS1210 and SCS1220 


MPM2400 

iCANnet 

iCANdin Link 


SCMH0410 

SCMI0402 

SCMS0810 

SCMR0816 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Doc. No: SCMS0410 Rev7 0115 









SCMS0810 

8 Channel x 10 Amp Switching Controller - DINrail Mount 

Key Features 

• 8 x 10 Amp switching source 

controller 







as required 


standards 



Overview 

This 8 channel 10 amp switching unit provides outstanding features and 

performance at a truly competitive price. It is rated at a maximum total load of 16 

amps single phase of continuous inductive lighting load. This unit is designed for 

switching lighting loads of most types. The unit is also available in an 4 channel x 

10 Amp version (SCMS0410). 











Mechanical 

Weight: 1 kg 






Dimensions 

Electrical 




Output channel current: Maximum 10 Amp 


Supply Protection: Provided by installer use 16A or less 

Load types: this unit is designed to work with most lighting load 

types. Please consult with the iLight® help desk for guidance 

on true load calculations. Care should be taken when specifying 

discharge lighting sources with power factor capacitors 


(Resistive and Inductive) 


circuit 


SCMS0410, SCS0410, SCS0420, SCS1210 and SCS1220 


MPM2400 

iCANnet 

iCANdin Link 


SCMH0410 

SCMI0402 

SCMS0810 

SCMR0816 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Doc. No: SCMS0810 Rev8 0115 









SCD24 

24 Channel DMX Source Controller 

Key Features 

• 24 channel DMX source 

controller module 


• Suitable for 5 Amp single 

phase supply 


inputs 


standards 


memory 



Overview 

The iLight 24 channel DMX source controller 

is designed to provide control of any DMX512 

controllable device. This product is of particular 

use for controlling DMX LED colour changing units 

and entertainment devices. Each channel can be 

assigned a DMX channel from within iCANsoft. The 

SCD24 can be controlled like any other iLight Source 

Controller using any of the iLight user interfaces to 

activate scenes and sequences.

Mechanical 

Weight: 2.5kg 











One RJ12 socket for programming the iCANnet TM 

network 

One set of terminals for the DMX output 

Electrical 

Supply: 230 volts -/+ 10% 50/60 Hz 1 Amp 

(optionally, 127 volt 60 Hz) 

Protection: Requires external circuit breaker 

Load Types: 

DMX controlled loads 




DMX output: 2 x 1mm 2 

Memory: 



Dimensions 






T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: SCD24 Rev5 1114 









SCD96 

96 Channel DMX Source Controller with 8 x 3A Relays 

Key Features 

• 96 DMX outputs 

• 8 x 3A volt-free change-over 

relays 

• Suitable for low voltage or 

resistive 230V loads 

• 8 x Analogue / Digital inputs 

• 8 x Digital outputs 

• 16 sequences with up to 128 

steps per sequence 

• Configurable iLight Area/ 

Channel Number 

• 128 Scenes per DMX Channel 

• RS485 port for connection to 

third party AV devices 

• 2 configurable auxiliary/alarm 

inputs 


memory 


standards 



Overview 

The iLight SCD96 is a 96 channel DMX source 

controller designed to provide control, with power 

switching, of any DMX512 controllable device. This 

product is of particular use for controlling DMX 

lighting devices including LED colour changing units 

and entertainment devices. 

Each channel can be assigned a DMX channel from 

within iCANsoft. The SCD96 can be controlled 

like any other iLight source controller using any of 

the iLight user interfaces to activate scenes and 

sequences. 

The unit incorporates 8 general purpose 3A relay 

devices which overlay channels 1-8 and 8 digital 

outputs which overlay channels 9-16. This is ideal 

for control of non DMX loads such as curtains, 

blinds or ballasts within an overall DMX installation.

Mechanical 

Weight: 2.5kg 








Control Connection: 

iCANnet TM network x 2 (Suitable for Belden 1502) 

CAN termination link 

RJ12 socket for network programming 

DMX terminals (DMX-512A) 

DMX termination link 

RS485 terminals 

Alarm input x 2 

Digital outputs x 8 

Analogue / Digital inputs x 8 

Electrical 

Supply: 

230 volts -/+ 10% 50/60 Hz 1 Amp (optionally, 127 volt 60 Hz) 

Protection: Requires external circuit breaker 

Load Types: 

DMX controlled loads (96 DMX addresses total) 

8 x Relay outputs 3Amps AC for general use resistive, incandescent 

lamps (tungsten) electric discharge (ballast) loads and 1/4 HP AC 

motor loads to use at 230VAC. Normally open and normally closed 

terminals available for line or low voltage use. 



Relay terminals: 4mm 2 


DMX output: 4 x 1mm 2 

Memory: 




Dimensions 





T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: SCD96 Rev4 1114 








Network Interfaces 

EG2 and EG2-NA 

iLight Network - Ethernet Gateway 

Key Features 

• Connects iLight’s iCANnet TM network to 10/100 Mbps 

Ethernet/LAN. 

• Configurable IP address. 

• Facilitates internet and Wi-Fi LAN connection into 

iCANnet TM . 

• Integral web server. 

• Supports iLight applications via mobile devices. 

(iPhone®/ iPod touch®/ iPad®) 

• Supports ASCII control strings. 

• 16 Sequences, each with a maximum of 128 actions. 

• Status LEDs. 

• Designed and manufactured to ISO 9001:2008 

standards. 

Overview 

The Ethernet Gateway provides a connection between an iLight 

network and an Ethernet LAN. This allows a user to control and 

configure the iLight system using iCANsoft on a LAN network PC 

or via the internet rather than by connecting directly into iCANnet TM . 

Where a wireless LAN is in place (or by connecting a wireless router 

into the Ethernet Gateway) the user can access the network with a 

Wi-Fi enabled PC. 

The Ethernet Gateway is also the host for the iLight series of remote 

applications including iOS (iPhone®/ iPod touch®/ iPad®) and a 

webserver front end where applications are downloaded separately. 

Coupling the EG-2 to a WIFI network enables secure scene control, 

visual feedback and modification from your hand held device. 

The Ethernet Gateway also facilitates connection to the internet 

when used with iCANsoft, a firewall, ISP and a Ethernet switch, 

this then enables remote connection for controlling, programming & 

obtaining diagnostics of the lighting control system. 

The Ethernet Gateway is available in two versions: 

EG2-NA - Ethernet Gateway including power supply and steel 

enclosure. 

EG2 - Ethernet Gateway in DINrail enclosure. Power Supply and 

metal DINRail enclosure available to order separately.

Mechanical - EG2 

Weight: 1 kg 






Mechanical - EG2-NA 

Weight: 2.5 kg 






Electrical - EG2 

Supply: Requires 9 - 36VDC 

(Optional 15V DINrail power supply available) 

Protection: Fully transformer isolated ethernet 

Electrical - EG2-NA 

Supply: Requires 100 - 240 VAC 

Protection: Fully transformer isolated ethernet 

Terminal Sizes: iCANnet TM cable size: 5 x 1.5mm 2 

Dimensions - EG2 

Dimensions - EG2-NA 


Application Download 

iOS for iPhone®/ iPod touch®/ iPad® - http://www.apple.com/itunes 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: EG2, EG2-NA Rev3 1014 








iLight Network Interfaces 

BN-2 

iLight Network to iLight Network Bridge 

Key Features 

• Configurable as Network 

Bridge Filter or Repeater 

• Allows division of large 

networks into logical 

segments 

• Single control of multiple 

iCANnet TM networks 

• Enables networks to grow 

beyond 1000m of cabling 

• Allows larger multi story 

applications to be installed 

and commissioned floor by 

floor. 


standards 



Overview 

The BN-2 bridging module allows 2 or 

more iLight iCANnet TM network segments 

to be connected together or arranged 

logically into floors or areas for ease of 

management. The bridge is also used to 

extend the network as a repeater where 

more than 1000m of cabling is required or 

more than 100 network devices are used 

on one segment. BN-2 also allows network 

messages to be filtered to ensure optimal 

performance in larger networks. 

BN-2 enables multiple segments with up to 

a total of 65,000 devices may be connected 

on one system. The bridge also ensures 

reliability of large systems by isolating and 

containing any network cabling faults. 

Dimensions 



Humidity: 5 - 95% non condensing 

Rating: IP20 


2-part aluminum housing. 

Mounting: 2 holes for screw 

mounting. 


Supply: 12Vdc via iCANnet TM 

May require separate power supply from 

network supply (eg isolated network 

backbone configuration) 

Network termination: Screw terminals 

within two part connectors, able to accept 

1.5mm 2 stranded or solid wire. 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: BN-2 Rev8 0614 

Changes to the products, to 

the information contained in 

this document, and to prices 

are reserved; so are errors and 

omissions. 






SI-2 

System Integrator 

Key Features 

• Configurable RS232 COMMS 

via 9 pin female D type (Send/ 

Recieve) 

• Adjustable baud rates of 

1200, 2400, 4800, 9600, 

19200, 38400, 57600, 115200 

• 100 RS232 Output Strings, 

up to 255 bytes each (ASCII 

or Hex) 

• 100 Output Actions, triggered 

by a “trigger” CAN message. 

Each action can send a RS232 

string, send a CAN message, 

or control a sequence 

• 100 RS232 Input Filters, up to 

255 bytes each (ASCII or Hex) 

• 100 Input Actions, triggered 

by a match on an input filter 

• 16 Sequences, each with a 

maximum of 128 actions 

• Status LEDs 


standards 



Overview 

The SI-2 System integration node is an 

RS232 converter for interfacing with 

third-party devices to and from iLight’s 

iCANnet TM network. 

The SI-2 enables control of a wide range 

of equipment through the iLight user 

interfaces such as: audio systems, TVs, 

projectors, blinds, curtains, heating and 

HVAC systems, Security & Fire alarms 

and BMS. 



Humidity: 5 - 95% non-condensing 


2-part aluminum housing. 

Mounting: 2 holes for screw mounting. 


Supply: 12Vdc via the network 

iCANnet TM network termination: Screw 

terminals within two part connectors, able 

to accept 1.5mm 2 stranded or solid wire. 

RS232: 9 pin female ‘D’ type connector 

Dimensions 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: SI-2 Rev6 0115 





omissions. 





iLight Interfaces 

RI-2 

Relay Interface 

Key Features 

• 8 Switch Outputs, for LED 

indication 

• 8 Relay Outputs – volt free 

changeover contacts with 

3A general rating 

• 8 inputs, programmable as 

analogue or digital 

• Digital inputs used for volt 

free switches, or motion 

detectors 

• Analogue inputs any 0-10v 

signal 

• 2 alarm / auxiliary inputs 

• Audio visual port RS485 

including 100 input strings, 

100 output strings and 

selectable Baud rate. 

• 16 sequences of 128 steps 

• EEprom program and 

sequence memory 


standards 


memory 



Overview 

RI-2 provides a versatile interface between an iLight 

system and other control systems. This compact 

unit can be mounted virtually anywhere. It has eight 

inputs, which may be programmed to be either digital 

or analogue. The unit also has eight volt-free mains 

rated low power relays. These allow a wide range of 

external equipment to be controlled. All inputs and 

outputs are fully programmable as to their function. 

This interface allows the iLight iCANnet TM network 

to control other systems and other systems to 

communicate with the iCANnet TM network. RI-2 

may be programmed to control curtains & blinds, 

screens, AV and other presentation equipment as 

well as controlling contactors for heavier power 

applications. With the control inputs set to analogue, 

any 0-10V source can be programmed to control 

system functions. The unit could also be programmed 

such that system sequences could be activated by a 

motion detector or other devices on the iCANnet TM 

network. The adaptability and versatility of this 

product make it an essential item in larger, more 

sophisticated venues where more than just lighting 

control is required.

Mechanical 

Power/Output Cable Access: 

5 x 25mm knockouts, 5 x PG16 knockouts 

Control Cable Access: 1 x 25mm knockout, 

1 x PG16 knockout 






One set of terminals for Audio Visual Port RS485 

One set of terminals for the switch inputs 

Control Outputs: 

One set of terminals for the LED outputs 

Relay Outputs: 

One set of terminals for the relay outputs 

Electrical 

Supply: 230 volts+/-10% 50/60Hz 

Protection: External protection required. 

Internal Electronics fuse only 


iCANnet TM cable size: 5 x 1.5mm 2 

Control input cable size: 10 x 1.5mm 2 

Switch output cable size: 9 x 1.5mm 2 

Audio Visual Port cable size: 2 x 1.5mm 2 

Relay output cable size: 24 x 1.5mm 2 

Switched outputs: 

8 x Volt free relays – changeover contacts rated 

230volts +/-10% 50/60Hz 3A resistive max 

Memory 


EEPROM for program and sequence memory 

Dimensions 





T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: RI-2 Rev3 1114 









STARBOX 

Star wire interface 


Power/Output Cable Access: 

5 x 25.5mm knockouts, 5 x PG16 

knockouts 

Control Cable Access: 1 x 25mm 

knockout, 1 x PG16 knockout 





Two sets of terminals for iCANnet TM 

network 

Overview 

Star wire interface provides network branch 

capability by allowing all cables from iLight’s 

iCANnet TM network to be connected back to 

one central point. 

The device enables an existing lighting 

control system in need of modernisation/ 

updating to be successfully converted to 

an iLight lighting control system. Up to six 

network segments may be connected per 

box. 

Dimensions 


Supply: Powered from iLight network 

Protection: 

Fully transformer isolated ethernet 


iCANnet TM network cable size: 5 x 1.5mm 2 

Control input cable size: 10 x 1.5mm 2 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: STARBOX Rev4 0115 





omissions. 






UIG-2 

Universal Interface 

Key Features 

• 4 opto isolated inputs, used for volt 

free switches, or motion detectors 

• 4 Analogue inputs 

• 4 Switch Outputs, for LED indication 


• 16 sequences with up to 128 steps 

per sequence 


• Partition Control 

• UL & CE compliant to all relevant 

standards 



Overview 

This unit provides a highly cost 

effective interface between 

an iLight lighting system and 

other control systems. Fitting 

in doublegang UK wallbox and 

powered through the iLight network 

cable, this compact versatile 

unit can be mounted virtually 

anywhere. It has four switch inputs 

and four analogue inputs, all fully 

programmable as to their function. 

In addition to the inputs there are 

four LED output drives for visual 

feedback of switch activity. There 

are also the essential connections to 

iLight’s iCANnet TM network. 

The unit allows other items to provide inputs to the iCANnet TM network, for example 

partition switches or fader controls. Configured for a room join function, just moving 

the partition will open or close the contact and automatically re-program the function 

of the control panels within the room. Alternatively a fader can be provided to set the 

overall level in an area using the units analogue inputs. The adaptability and versatility 

of this product make it an essential item in more sophisticated venues.

Mechanical 

Mounting: standard 47mm deep UK double gang 

backbox (not provided) 





iCANnet TM network, suitable for Belden 1502 

4 switch inputs (Opto isolated) 

4 analogue inputs 

Control Outputs: 

4 LED outputs 

Electrical 

Supply: +12V (via iCANnet TM network cable) 


iCANnet TM network cable size: 5 x 1.5mm 2 

Switch input cable size: 5 x 1.5mm 2 

Analogue input cable size: 5 x .5mm 2 

Switch output cable size: 4 x 1.5mm 2 

Memory: 


EEPROM for program and sequence memory 

Dimensions 





T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: UIG-2 Rev6 0115 








iLight Accessories 

TC-1 

Astronomical Time Clock 

Key Features 

• Astronomical time clock 

including day, date, sunrise, 

sunset functions 

• Scene selection and 

programming 

• Channel level raise and 

lower 

• Task / sequence 

programming 

• Scene and channel naming 



Overview 

Surface mounting electronic time 

clock with astronomical facility and 

LCD display. Fully programmable 

using iCANsoft for daily or date 

specific events. Connects to iLight’s 

iCANnet TM network. Keyboard 

allows scene selection and event 

functions to be enabled / disabled. 

The iLight TimeClock enables the 

user to have the following functions; 

astronomical time clock, scene 

programming and scene selection 

into one simple control panel.

Mechanical 

Weight: 1.1kg 

Mounting: attached via bracket to standard 35m 

double gang wallbox - not provided, or screwed 

directly to surface. 





One set of terminals for iCANnet TM network 


Dimensions 

Electrical 

Supply: +12VDC (via iCANnet TM network cable) 

Termination: 

Network: Screw terminals within two part connectors, 


Programming: Via iCANsoft. 

Functionality: 

Select scenes 


Channel level raise and lower 



Time clock 

Date range - recurring events 

One shot events 

Leap year 

Daylight saving setting 

Astronomical timeclock with offset facility 

Date / day omission 



Memory: 







T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: TC-1 Rev5 0115 









UIM 

Mini UIG 

Key Features 

• 6 inputs which each can be 

individually configured as 

0-10V analogue, digital or 

photoelectric cell inputs 

• 8 sequences with up to 30 

steps per sequence 

• Only 42mm Ø so easily fits 

in European and UK junction / 

back boxes 


standards 



Overview 

iLight network powered universal 

interface with Six configurable inputs. 

Can be dry loop contact closure for 

scene selection or 0-10V analogue 

inputs. 42mm diameter potted PCB 

with 20cm flying leads, designed to 

fit European back boxes and ideal for 

connection to “dumb” push buttons 

and rocker switches. Does not include 

LED tellback. 

Dimensions 

45mm 

14mm Deep 

45mm 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: UIM Rev4 0115 





omissions. 






UIS 

Universal Interface - Sensors 

Key Features 

• 3 x connections for sensors to 

iCANnet TM network. 

• RJ12 type sockets for rapid sensor 

connection. 

• 3 independant daylight linking engines. 

• Presence or absence detection support. 

• Infra-red support for HH17IR remote 

controller. 

• Supports Infra-red identification. 

• 16 Sequences, each with a maximum of 

128 actions. 

• Status LEDs. 

• CE compliant to all relevant standards. 


ISO 9001:2008 standards. 

Mechanical 



Material: 2-part aluminum housing. 

Mounting: 6 holes for screw mounting. 

Electrical 

Supply: 12VDC via the iCANnet TM network 

Network termination: Screw terminals within 

two part connectors, able to accept 1.5mm2 

stranded or solid wire. 

3 x RJ12 connections to AXCS01SRJ 

Combined Sensor and others - Consult iLight 

for more information. 

Overview 

The UIS enables 3 separate sensor 

groups with 6 sensors in total to 

be connected to iLight’s iCANnet TM 

lighting control network. 

(Max cable length for each group 

30m). Each sensor can be either 

a single occupancy detector or 

daylight sensor or a combined PIR, 

Photocell with built in infra-red 

control. 

Each UIS installed adds three 

independant daylight linking 

engines to the network making 

this unit ideal for maximising 

daylight harvesting across all 

areas. 

This small compact device can 

be deployed anywhere on the 

iCANnet TM network and uses 

RJ12 sockets and cables for rapid 

sensor installation. 

Accessories: 

AXCS01SRJ - 

Low Voltage Multi Sensor. 

AXCA05RJ - 

5m Cable RJ12 to RJ12 (LSOH) 

AX-FFRJ12 - 

RJ12 to RJ12 Female Coupler 

AX-2FIMRJ12 - 

2 Female to 1 Male Doubler 

Dimensions 




T: +44 (0)1923 495495 F: +44 (0)1923 228796 

E: lightingcontrolsolutions@eaton.com www.coopercontrols.co.uk 





Eaton.eu 

© 2014 Eaton 


Document No: UIS Rev3 1014 





omissions. 





System Interfaces 

BMS INTERFACE 

Network Interface Module for Buiding Management Systems 

Key Features 

• LON, BACnet, Modbus 

• 200 areas (points) supported 

• Configurable using built in 

web server 

• DINrial mounted 

• Compatible with iLight and 

Greengate lighting control 

systems 

Overview 

Integrated buildings require integrated 

building management tools for a 

comprehensive building control solution. 

This BMS Interface supports a wide range of 

control protocols to act as a bridge between 

Eaton’s intelligent lighting control networks 

and a central BMS management system. 

The BMS interface is supplied complete with 

a steel enclosure including power supply 

and configuration files. This unit connects to 

systems using BACnet IP, LON and Modbus, 

allowing scenes in up to 200 areas (200 

points) to be selected and monitored from 

the BMS system. Scene changes on the 

lighting control system will be notified to the 

BMS. An on board Webserver is provided 

on the BMS interface for basic configuration 

and set up. 

Connection to BMS system is by either IP, 

RS485 or 2 pin terminals for LON. 

Connection to an Greengate lighting control 

system can be via IP using a Greengate 

head-end computer. Connecting to an iLight 

lighting control system can be via IP using an 

EG2 or via RS232 using an SI-2.

Technical Information 


MEMORY: 

4096 LON Network Variables 

Connection to BMS via 

iLight SI-2 - RS232 

SOURCE 

CONTROLLER 

SUPPLY VOLTAGE: 

15V DC 1Amp 

BMS 

INTERFACE 

RS485 

BACNET IP 

or 

LON 

or 

MODBUS 

CONNECTIVITY: 

LON TP78Kbps 

RS485: Modbus, BACnet, Other 

Ethernet: BACnet 

iLight 

Network 

SI-2 

PHYSICAL: 

Enclosure: UL94-V1 Grey Plastic 

Weight: 0.275 kg 

Dimension: L:157mm W:98mm D:59mm 

(ex. connectors ) 

Mount: TS35 DIN Rail ( Len: 155mm ) 


iLight EG-2 - IP 

SOURCE 

CONTROLLER 

BMS 

INTERFACE 

RS485 

BACNET, 

LON or 

MODBUS 

CONNECTORS: 

Power: 2 Part screw terminals 

LON®: 2 Part screw terminals 

RS485: 2 Part screw terminals 

Ethernet: RJ45 

ENVIRONMENTAL: 

Storage: -20 °C to 70 °C 

Operating: 0 °C to 60 °C 

Humidity: 0 to 90%RH non-condensing 

iLight 

Network 

IP 

ETHERNET 

IP 

EG-2 

IP to BMS 


Greengate PC - IP 

BMS 

INTERFACE 

RS485 

BACNET, 

LON or 

MODBUS 

IP 

ETHERNET 

IP to BMS 

IP 

CAN Spine Bus* 

* If CAN Network is used 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Doc. No: BMS INTERFACE Rev4 1114 








iLight Sensors 

NS3 

Network Sensor with Combined PIR, Daylight and IR Control 

Key Features 

• Excellent sensitivity to small 

movements using Quad-Pyro 

technology 

• Greater sensor stability with reduced 

noise susceptibility 

• 360 degree detection area 

• Ceiling flush mounted for a low profile, 

unobtrusive installation 

• Compact 49mm diameter size ideal for 

suspended ceilings, chilled beam and In 

fill plate applications 

• Connects directly to the iLight 

iCANnet TM Network 

Overview 

The NS3 multi sensor can be connected 

directly to the iLight iCANnet TM Network via 

CAN terminals. It features 3 functions: PIR 

motion detection, daylight measurement and 

an infra-red receiver. All three functions may 

be programmed within the iLight software 

according to specific user needs. 

This sensor features a movement detection 

coverage of up to 8.5m diameter depending on 

installation height with PIR detection optimised 

for Slight Motion for superior performance. 

The PIR feature may be set in absence 

or presence detection mode with variable 

programmable timing. 

The daylight feature is used to maintain 

constant light level where controlled luminance 

(daylight linking) is required. 

In operational mode the infrared receiver may 

select scenes, turn lighting on/off and adjust 

levels locally with the iLight remote controller 

(HH17IR). 

The NS3-C sensor’s 

combined features ensure 

maximum energy savings 

as well as great flexibility for 

the user.

Suitable For 

Cellular office 

Open plan office 

School classroom 

Lecture theatre 

Retail complex 

Public library 

Sports hall 

Airport terminal 

Hospital wards 

Factory production area 

Corridor & staircases 

Foyer & atriums 

Plant room 

Storeroom 

Consulting room 

Meeting room 


Construction: Circular plastic housing 

UL94 V0 rated 

Dimensions: 

Diameter front 49mm, rear 39mm Depth 30mm 

Fixing: 2 x spring clips 

Mounting Hole Diameter: 40 to 45mm Diameter 

depending on ceiling material 

Weight: 35g 

Temperature: 0 to 45°C (non condensing) 

Supply: 9 - 24V dc (regulated) 

Load data: 10m A @ 15V 

Max recommended mounting height: 3.4m 

Operating Parameters 

• Connects directly to the iLight Network 

• Controls any luminaire anywhere on the 

System 

• Presence and Absence functionality 

• Light Thresholds, Scenes and Time Outs 

programmed & adjusted at any time in 

software. 

• Built-in flexbility to suit individual user 

requirements 

Dimensions 


NS3 

Combined Sensor 

iCANnet TM 

(Belden 1502) 

Options 

Remote Controller - HH17IR 

(Order Separately) 

Surface mounting box - AX-SMA1 


Detection 

The differences in the detection 

zone patterns are indicative of the 

projections of the 26 lenses with 

single focal point and with three 

optical axis. 

An object whose temperature 

differs from the background 

temperature and which crosses 

inside the detection zone will be 

detected. 

Detection range is typically 

calculated at the working plane 

(900mm off the floor) 

Detection Area - Zone patterns at the optimal slight 

motion detection distance of 2m from sensor 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: NS3 Rev2 1214 









AXCS01SRJ 

Combined PIR, Daylight and I/R Sensor 

Key Features 

• Excellent PIR sensitivity to small 

movements using Quad-Pyro 

technology 

• Greater Sensor stability with reduced 

noise susceptibility 

• 360 degree detection area 

• Multiple PIR outputs may be used in 

Parallel for larger areas of coverage 

• Daylight level detector with directional 

aspect 

• Detectors sit flush mounted in the 

ceiling tile 

• Compact 49mm Diameter size for 

recess installation in Chilled Beam and 

In fill Plate application 

• Simple extension connection using 

RJ12 connector on rear of unit 

• Supplied complete with 5 metre lead to 

connect to Lighting Control Systems 

Overview 

This low voltage multi sensor combines PIR 

presence detection and a photocell in one 

compact flush mounting design using an RJ12 

connector on the rear of the unit. 

The action of the photocell and PIR presence 

detector are separate. When used in conjunction 

with an iLight UIS Sensor Interface a third infrared 

reciever mode is also enabled. The infra-red 

receiver may be used to select scenes, turn 

lighting on/off and adjust levels locally with the 

iLight remote controller (HH17IR). 

Ideal for intelligent lighting 

control systems that deploy 

system programmed 

intelligence. This multi 

sensor is perfect for 

applications where space is 

at a premium. 

The AXCS01SRJ sensor’s combined features 

ensure maximum energy savings as well as 

great flexibility for the user.

Suitable For 





Retail complex 


Sports hall 

Airport terminal 

Hospital wards 


Corridor & staircases 

Foyer & atriums 

Plant room 

Storeroom 


Meeting room 


Fixing: 2 x Spring Clip 

Mounting Hole Diameter: 40 to 45mm Diameter 

depending on ceiling material 

Weight: 35g 

Temperature: 0 to 45°C (Non Condensing) 

Supply: 12 - 24V dc (Regulated) 

Construction: Circular Plastic Housing UL94 V0 rated 

Load data: 8m A @ 15V 

Max recommended mounting height: 3.4m 

Dimensions 

Remote Controller - HH17IR 


Surface mounting box - AX-SMA1 


Detection 

The differences in the detection 

zone patterns are indicative of 

the projections of the 26 lenses 

with single focal point and with 

three optical axis. 

An object whose temperature 

differs from the background 

temperature and which crosses 

inside the detection zone will be 

detected. 

Detection range is typically 

calculated at the working plane 

(900mm off the floor) 

Detection Area - Zone patterns at the optimal slight 

motion detection distance of 2m from sensor 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: AXCS01SRJ Rev6 0614 








Sensors 

PE1C 

Internal Recessed Ceiling Mounted Photocell 

Key Features 

• Photocell used to determine 

light level in an interior space 

• 0-1200 lux at the working plane 

• Compact 47mm Diameter size 

for recessed installation in 

Chilled Beam and In fill Plate 

application 

• Used within an iLight lighting 

control system 

• External version also available 

(PE1EXT) 


standards 




Climate Range (IP20) 




Supply: 12Vdc 

(via iLight UIM interface unit) 

Power consumption: 0.1mA 

Overview 

This unit is a internal ceiling mounted ‘look down’ 

Photo-diode Sensor designed for measuring 

light level. Used as an input device to iLight 

networks, ambient light levels can be controlled 

by dimming and switching artificial lighting when 

needed to save energy. Used with an iLight UIM 

(Mini Universal Interface), iCANsoft may be 

programmed to control theshhold lighting levels 

and instigate network commands. Multiple light 

level commands are also possible, consult iLight 

for detailed system design. 

An external photocell is also available (PE1EXT) 

where the measurement of exterior light levels 

is required. It is the same specification as the 

internal unit but mounted in an IP65 housing. 

Mounting 

38mm diameter hole through the ceiling 

tile and then retained using the metal clip 

supplied. It can also be fitted by using a 

surface adaptor box which is available from 

iLight. External sensor supplied with own 

mounting bracket. 

This unit is hard wired and supplied with a 1m 

trailing cable 

Recommended maximum cable length 

between UIM and sensor: 10m (Screened) 

Dimensions 

Location 

The sensor should be mounted on a rigid 

surface a suitable distance away from any 

light fittings’ 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: PE1C Rev5 1114 





omissions. 






PI1C 

Internal Ceiling Recess Mounted Motion Detector 

Key Features 

• Ceiling mounted Passive Infra-Red 

detector 

• Compact 47mm Diameter size for 

recess installation in Chilled Beam 

and In fill Plate application 

• Used within an iLight lighting control 

system 

• Action used to trigger events and 

scenes within iCANsoft 

• Small compact design 


standards 



Overview 

This unit is an internal ceiling mounted 

Passive Infra-Red detector used to 

detect movement of people in an 

area. It is designed to be recessed 

into a ceiling tile and can be installed 

individually in a small room or in 

groups to cover a larger area. 

The unit allows iLight system 

functions to be triggered automatically 

when a person enters an area. It 

works by detecting the infrared 

radiation given off by the human body 

and gives a signal to an iLight interface 

unit (UIG or UIM)

Suitable For 



Meeting room 


Small workshop 

Plant room 

Storeroom 

Hospital ward (multi-person) 

Hospital ward (single person) 


Storeroom 




Library (bookstack) 

Corridor 

Atrium 

Staircase 

Foyer 

Hotel lounge 

Shop 

Restaurant 


Mechanical 

Climate Range (IP20) 



Mounting 

38mm diameter hole through the ceiling tile and 

then retained using the metal clip supplied. It can 

also be fitted by using a surface adaptor box which 

is available from iLight. 

This unit is hard wired and supplied with a 1m 

trailing cable 

Recommended maximum cable length between 

UIM and sensor: 10m (screened) 

Location 

The sensor should be mounted on a rigid surface 

where it has a clear view of the occupancy zone, 

and should preferably be mounted in front of rather 

than behind activity. 

Avoid placing adjacent to forced air heating or 

cooling systems (1 metre or more indirect flows) as 

well as high powered RF equipment including pager 

aerials and inductive loop equipment. 

Detectors should be placed at 5 metre intervals to 

ensure detection patterns overlap. 

Dimensions 

Detection Pattern 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: PI1C Rev6 1114 








Sensors 

PE1-EXT 

External Ceiling Surface Mounted Photocell 

Key Features 

• Photocell used to determine light level in 

an interior space 

• IP65 rated 

• 0-1500 lux 

• Designed to be surface mounted 

• Used within an iLight lighting control 

system 

• Interior version also available (PE1C) 




Electrical 

Supply: 5Vdc (via iLight UIM interface unit) 

Power consumption: 0.1mA 

Mechanical 

Climate Range: IP65) 



Mounting: Supplied with own mounting 

bracket. The unit may be mounted in any 

suitable position - avoid water falling directly 

on face 

Recommended maximum cable length 

between UIM and sensor: 

10m (screened) 

Location: The sensor should be mounted on a 

rigid surface a suitable distance away from any 

light fittings’ 

Overview 

This IP65 rated unit is a external 

surface mounted 

Photo-diode Sensor designed for 

measuring light level. Used as an 

input device to iLight networks, 

ambient light levels can be 

controlled by dimming and switching 

artificial lighting when needed to 

save energy. Used with an iLight 

UIM (Mini Universal Interface), 

iCANsoft may be programmed to 

control theshhold lighting levels 

and instigate network commands. 

Multiple light level commands are 

also possible, consult iLight for 

detailed system design. 

An internal photocell is also available 

(PE1C) where the measurement 

of interior light levels is required. 

It is the same specification as this 

external unit but designed for recess 

mounting in internal ceiling tiles. 

Dimensions 




T: +44 (0)1923 495495 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: PE1-EXT Rev4 1014 





omissions. 





iLight Software 

SW2 

Configuration Software Kit 

Key Features 

• PC Node - Serial Port to 

iCANnet TM network interface 

• Includes a copy of iCANsoft 

on CD to allow iLight’s 

iCANnet TM network to be 

configured from a PC 

Overview 

This kit allows engineers to connect their 

PC to the iLight system and configure the 

network using iCANsoft. 

• Includes USB cable 

• Includes iCANnet TM network 

connection adapter PCB 

Note: PC node available separately 

for adding RS485 input to any iLight 

network 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: SW2 Rev4 0115 





omissions. 






iCANview - Floor Plan 

iCANview floor plan monitoring software, single user license. 

Key Features 

• Ideal for monitoring large 

or complex installations. 

• Each system customised 

to your needs. 

• Navigate multiple floors. 

• Selectable levels of detail. 

• Vitual device control and 

feedback, including DALI 

reporting where applicable. 

• Zoom & pan functions. 

• Includes iCANview-Scene 

Control capabilities. 

• Windows 7, 8 & 8.1 

compatible. 

Overview 

Ideal for use by monitoring and maintenance 

staff in control rooms for iLight lighting 

network installations. 

iCANview Floor plan stand alone software 

is used for monitoring a lighting installation 

using a floor plan layout based on original 

customer supplied drawings. Each Floor plan 

is custom created for each site using the 

iCANsoft program database and a zoomable 

WMF file and may include multiple floor 

levels and layouts including position, type and 

connections for each iLight network device. 

Selectable views include, show: device, 

fixtures, device connections, sensor 

connections and fixture connections. 

Zoom function enables specific areas to be 

monitored in detail. Lighting Control System 

information readouts vary by device type 

and capability but do not exceed, where 

appropriate, fixture type, device, name, 

output, level, area scene and channel 

numbers. (based upon Full DALI feedback). 

Suitable for operation on a desk top or laptop 

PC running windows 7, 8 or 8.1. 

Includes software single user license. License 

includes scene selection functions by area. 

Initial layouts and images supplied by customer.

Ordering Information 

iCANview-Floor Plan 

Items included in license: 

Single User - iCANview Floorplan, License, 

Floorplan design service as per iCANView design 

agreement 

Items not included in license: 

Desktop Computer 

PC- Node 

On-site Commissioning 

On-site Training 

Please enquire separately for multi-user and 

multi site user licenses. 


iCANview-Floor Plan package including PC 


Single User - iCANview Floorplan, License, 

Floorplan design service as per iCANView design 

agreement 

Desktop Computer including Windows 

Monitor 

Keyboard 

Mouse 

PC- Node 









T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Doc. No: iCANview Floorplan Rev4 1114 









iCANview - Scene Control 

iCANview remote scene control software, single user license. 

Key Features 

• Ideal for monitoring large 

or complex installations. 

• Each system customised 

to your needs. 

• Navigate multiple floors. 

• Selectable levels of detail. 

• Vitual device control and 

feedback, including DALI 

reporting where applicable. 

• Zoom & pan functions. 

• Includes iCANview-Scene 

Control capabilities. 

• Windows 7, 8 & 8.1 

compatible. 

Overview 

Ideal for use in reception areas, supervisor 

offices and control rooms where general staff 

may be required to operate preprogrammed 

lighting scenes within selected areas on an 

iLight iCANnet TM lighting network. 

Uses a graphical layout – presentation is 

based on simple user supplied icons or 

pictures of the installation (jpg or bitmap) for 

easy navigation of layers. Used for recall and 

running of preprogrammed lighting scenes by 

area. Each solution is custom created using 

the iCANsoft program database for each site 

specific application and may include multiple 

layers and pictures overlaid with scene 

selection buttons 

Suitable for operation on a desk top or laptop 

PC running windows 7, 8 or 8.1. 

Initial layouts and images supplied by customer.

Ordering Information 

iCANview - Scene Control 


Single User - iCANview Scene Control, License, 

Layout design service as per iCANView design 

agreement. 


Desktop Computer 

PC- Node 





iCANview - Scene Control package including PC 


Single User - iCANview Scene Control, License, 

Layout design service as per iCANView design 

agreement. 

Desktop Computer including. 

Monitor. 

Keyboard. 

Mouse. 

PC- Node. 










T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2014 Eaton 


Doc. No: iCANview Scene Control Rev4 1114 








iLight Accessories 

HH17IR 

iLight Infra-Red Handset 

Key Features 

• 8 scene buttons 

• Off button 

• Raise and lower controls 

• 6 additional configurable 

buttons 

• LED indication when button 

is depressed and the IR 

command is being sent 

• Uses standard RC5 IR codes 

• Up to 15m range 



Overview 

The iLight infrared handset enables 

scenes to be selected remotely via 

an iLight control plate IR receiver. 

This stylish remote control offers the 

selection of eight scenes, off, raise 

and lower as well as six additional 

configurable buttons used to extend 

the capability of the remote to control 

extra scenes or third party devices 

such as curtains and blinds (action 

configured within iCANsoft). 


3Vdc, 2 x AAA batteries (included) 


Ergonomic black plastic case with 

rear battery compartment cover. 




Dimensions 




T: +44 (0)1923 495496 F: +44 (0)1923 228796 






Eaton.eu 

© 2015 Eaton 


Document No: HH17IR Rev3 1014 





omissions.

Datasheets - iLight

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?