Schneider Electric Professional System Operations Course - Xantrex

Schneider Electric
Professional System
Operations Course
Three day Schneider Electric Xantrex
Xantrex GT Three Phase Professional
System Operations Course*
Schneider Electric Professional System Operations Course is a three day course
for qualified technicians and service oriented personnel looking to gain
knowledge and hands on experience in operation and basic troubleshooting
of Schneider Electric’s three phase inverter systems.
Classes are small, so register early!
Spaces will be filled on a first come basis.
Upcoming course
dates and locations:
GT250
June 15-17, 2010
Xantrex Technology, Livermore;
161-G South Vasco Rd., Livermore, CA
GT250
July 13-15, 2010
Xantrex Technology, Livermore;
161-G South Vasco Rd., Livermore, CA
GT500 MV
August 17-19 / 2010:
Xantrex Technology, Livermore;
161-G South Vasco Rd., Livermore, CA
*NABCEP continuing education credits available for all of the above courses.
www.schneider-electric.com

Schneider Electric Professional System Operations Course
Course description
Xantrex GT500 MV Training
This course is intended for current or prospective Schneider Electric Xantrex three phase system
owners or those responsible for servicing the systems.
Pre-requisite: Osha 1910 & NFPA 70E High voltage training completion.
Some prior knowledge of basic electrical circuits and concepts such as Ohms Law.
Course content:
The focus of this course is on the Schneider Electric Xantrex three-phase grid-tie series product line. The format
of the training is a small workgroup with a focus on hands-on training with open dialogue. The course covers a brief
overview of conventional and renewable energy sources, an introduction to grid-tie energy transfer, an overview of
Schneider Electric grid-tie products, and detailed discussion of the Xantrex GT Three Phase Series features, functions
and benefits. Upon completion of the course, participants will have working knowledge of System Start-up, Operation
and proper Shutdown procedures. We will cover the communication protocols and application used for retrieving
system logs. Best maintenance practices will be covered as well as trouble code analysis.
Course description
Xantrex GT250 Training
This course is intended for current or prospective Schneider Electric Xantrex three phase system
owners or those responsible for servicing the systems.
Pre-requisite: Osha 1910 & NFPA 70E High voltage training completion.
Some prior knowledge of basic electrical circuits and concepts such as Ohms Law.
Course content:
The focus of this course is on the Schneider Electric Xantrex three-phase grid-tie series product line. The format
of the training is a small workgroup with a focus on hands-on training with open dialogue. The course covers a brief
overview of conventional and renewable energy sources, an introduction to grid-tie energy transfer, an overview of
Schneider Electric grid-tie products, and detailed discussion of the Xantrex GT Three Phase Series features, functions
and benefits. Upon completion of the course, participants will have working knowledge of System Start-up, Operation
and proper Shutdown procedures. We will cover the communication protocols and application used for retrieving
system logs. Best maintenance practices will be covered as well as trouble code analysis.
Training information
Cost:
The cost for the three day course is $300.00 US per attendee.
Please note: due to the hands on nature of the training, attendance is limited to 6 people per session.
To register, please fill out the attached registration form.
For more additional information, please contact Phil Robinson at phil.robinson@ca.schneider-electric.com

Schneider Electric training registration form
Please use this form to register for the Schneider Electric
Professional System Operations Courses.
Please fill in the required information below.
161 G South Vasco Rd.,
Livermore, CA 94551
Phone: 925.245.5339
Fax: 925.449.1279
Courses:
Please pick the dates for your training session by circling the dates on the right
GT250 Training Session June 15-17
GT250 Training Session July 13-15
GT500 MV Training Session August 17-19
Please contact Phil Robinson for future dates. (see email below)
Attendee information:
Company name:
Company address:
Company phone:
Attendee name:
Attendee name:
Attendee name:
Attendee name:
Attendee name:
Company fax:
email address:
email address:
email address:
email address:
email address:
$300 for a three day session (per attendee), per course
Breakfast and lunch will be provided at no additional charge. Hotel, dinner and transportation costs not included.
Payment may be made by credit card or check. Please fill in the registration information and fax or e-mail the completed form
to Phil Robinson – e-mail: phil.robinson@ca.schneider-electric.com | fax: 925.449.1279
You will be contacted by e-mail or phone to complete the registration process.
Please do not make travel arrangements prior to receiving registration confirmation.
Cancellation policy: cancellation requests must be made no later than 5 days prior to the training date. No refunds will be made thereafter.
In the event a course is cancelled by Schneider Electric, the registrant understands that Schneider Electric will not be held responsible for
any costs incurred by the registrant except for the refund of the course cost.
©2010 Schneider Electric. All rights reserved. Xantrex, Schneider Electric and Schneider Electric logo are trademarks
or registered trademarks of the Schneider Electric group of companies.