Schneider Electric Professional Installer Training - Xantrex

Schneider Electric
Professional
Installer Training
Three day Schneider Electric Xantrex
Xantrex GT Three Phase Professional
Installer Training *
Schneider Electric Inverter system operations training is a two and a half day
course. This training course is for qualified technicians, and service oriented
personnel looking to gain knowledge and hands on experience in operation
and basic troubleshooting of Schneider’s threephase inverter systems.
Classes are small, so register early!
Spaces will be filled on a first come basis.
Upcoming course dates and locations:
GT500 MVX
July 26-28 / 2011
GT500 MVX
August 16-18 / 2011
GT500 MVX
September 13-15 / 2011
System Training
October 11-13 / 2011
System Training
November 8-10 / 2011
System Training
December 13-15 / 2011
Xantrex Technology, Livermore;
161-G South Vasco Rd., Livermore, CA
*NABCEP continuing education credits available for all of the above courses.
www.schneider-electric.com

Schneider Electric Interactive Professional Installer Training
Course description
Xantrex GT500 MVX (GT500 E training available on a per request basis)
This course is intended for current or prospective Schneider Electric Xantrex three phase system
owners or those responsible for servicing the systems.
Pre-requisite: Osha 1910 & NFPA 70E High voltage training completion.
Some prior knowledge of basic electrical circuits and concepts such as Ohms Law.
Course content:
The focus of this training is on the Schneider Electric Xantrex three phase, grid-tied series product line. The format
of the training is a small workgroup with a focus on hands-on training with open dialogue. The course covers a brief
overview of conventional and renewable energy sources, an introduction to grid-tie energy transfer, an overview of
Schneider Electric grid-tie products, and detailed discussion of the Xantrex GT Three Phase Series features, functions
and benefits. Upon completion of the course, participants will have working knowledge of System Start-up, Operation
and proper Shutdown procedures. We will cover the communication protocols and application used for retrieving
system logs. Best maintenance practices will be covered as well as trouble code analysis.
Course description
Xantrex GT250 Training (Offered on a per request basis)
This course is intended for current or prospective Schneider Electric Xantrex three phase system
owners or those responsible for servicing the systems.
Pre-requisite: Osha 1910 & NFPA 70E High voltage training completion.
Some prior knowledge of basic electrical circuits and concepts such as Ohms Law.
Course content:
The focus of this training is on the Schneider Electric Xantrex three phase, grid-tied series product line. The format
of the training is a small workgroup with a focus on hands-on training with open dialogue. The course covers a brief
overview of conventional and renewable energy sources, an introduction to grid-tie energy transfer, an overview of
Schneider Electric grid-tie products, and detailed discussion of the Xantrex GT Three Phase Series features, functions
and benefits. Upon completion of the course, participants will have working knowledge of System Start-up, Operation
and proper Shutdown procedures. We will cover the communication protocols and application used for retrieving
system logs. Best maintenance practices will be covered as well as trouble code analysis.
Training information
Cost:
The cost for the three day training is $300.00 USD per attendee.
Please note: due to the hands on nature of the training, attendance is limited to 6 people per session.
To register, please fill out the attached registration form.
For more additional information, please contact Phil Robinson at SERenBUTraining@schneider-electric.com
Customized off-site training also available. Please contact us for more information and a quotation.

Schneider Electric training registration form
Please use this form to register for the Schneider Electric
Interactive Professional Installer Training courses.
Please fill in the required information below.
Courses:
161 G South Vasco Rd.,
Livermore, CA 94551
Phone: 925.245.5339
Fax: 925.449.1279
Please pick the dates for your training session by circling the dates on the right
GT500 MVX Training Session July 26-28
GT500 MVX Training Session August 16-18
GT500 MVX Training Session September 13-15
System Training October 11-13
System Training November 8-10
System Training December 13-15
Please contact Phil Robinson for future dates. (see email below)
Attendee information:
Company name:
Company address:
Company phone:
Attendee name:
Attendee name:
Attendee name:
Attendee name:
Attendee name:
Company fax:
email address:
email address:
email address:
email address:
email address:
$300 for a three day session (per attendee), per course
Breakfast and lunch will be provided at no additional charge. Hotel, dinner and transportation costs not included.
Payment may be made by credit card or check. Please fill in the registration information and fax or e-mail the completed form
to Phil Robinson – e-mail: SERenBUTraining@schneider-electric.com | fax: 925.449.1279
You will be contacted by e-mail or phone to complete the registration process.
Please do not make travel arrangements prior to receiving registration confirmation.
Cancellation policy: cancellation requests must be made no later than 5 days prior to the training date. No refunds will be made thereafter.
In the event a course is cancelled by Schneider Electric, the registrant understands that Schneider Electric will not be held responsible for
any costs incurred by the registrant except for the refund of the course cost.
©2011 Schneider Electric. All rights reserved. Xantrex, Schneider Electric and Schneider Electric logo are trademarks
or registered trademarks of the Schneider Electric group of companies.