Printrex 980 Operator's Guide - TransAct

More documents

Recommendations

Info

Appendix B: Frequently Asked Questions Work at Rack Unit Replacement 1) Adjust Rack Unit at same position as noted number that was noted when Rack Unit was removed, and then tighten screws. Rear Feeder Sensor Adjustment 1) Insert paper in the feeder slot provided on the back of Printer more than 1 sheet to cover Rear Feeder Sensor. Page 148 100-11672 - Rev C
Appendix A: Ordering Genuine Ithaca Supplies 2) Connect PC to Printer, and then start service utility. Open [Parts Replacement] tab, and then click [Adjust] to adjust Rear Feeder Sensor. 3) Confirm that Rear Feeder Sensor is "ON". 100-11672 - Rev C Page 149
Page 1 and 2:
Operators Guide 100-11672 Rev C, Au
Page 3 and 4:
Change History Revision Changes Dat
Page 5 and 6:
Radio Frequency Interference Statem
Page 7 and 8:
Table of Contents Change History ..
Page 9 and 10:
Spur Marks (Dotted Lines) .........
Page 11 and 12:
Chapter 1 Introducing your Printrex
Page 13 and 14:
About Your Printrex ® 980 Printer
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Chapter 2 Safety Precautions 100-11
Page 21 and 22:
Important Safety Precautions Genera
Page 23 and 24:
Handling the Printer and Accessorie
Page 25 and 26:
Chapter 3 Step-by-Step Installation
Page 27 and 28:
Step-by-Step Installation Instructi
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99:
Page 102 and 103:
This page intentionally left blank
Page 104 and 105:
Printrex ® 980 Specifications and
Page 107 and 108: Chapter 5 Printer Maintenance 100-1
Page 109 and 110: How to Operate the Printrex ® 980
Page 119: How to Operate the Printrex ® 980
Page 122 and 123: This page intentionally left blank
Page 124 and 125: Appendix B: Frequently Asked Questi
Page 208 and 209:
Appendix B: Frequently Asked Questi
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
Page 294 and 295:
Page 297:
Index Index Cleaning the printer, 9
show all

Printrex 980 Operator's Guide - TransAct

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?