Table 6 合 金 及 變 性 <strong>PPS</strong> 系 列 / Alloy and modified <strong>PPS</strong> series. 材 料 編 號 (Grade No.) SE-730 SE-760 W-30 WL-30 Properties 項 目 構 成 和 特 性 GF 30% GF / Filler GF 30% GF & PTFE General Information (Properties) (General Information) <strong>PPS</strong> / PPE <strong>PPS</strong> / PPE 變 性 / Modified 變 性 / Modified alloy alloy "AMORVON" 滑 動 / Lubricant "AMORVON" 物 理 性 質 試 驗 方 法 (Test Method) Physical ASTM 單 位 (Unit) 比 重 D-792 g / cm 3 1.48 1.82 1.57 1.68 Specific gravity 吸 水 率 23℃/24 時 間 ( 在 水 裏 ) D-570 Wt・% 0.04 0.02 0.06 0.05 Water absorption, 23℃ / 24h. / in water 成 形 收 縮 率 MD / TD a D-955 % 0.30 / 1.0 0.25 / 0.9 0.25 / 1.0 0.25 / 1.0 Mould shrinkage, MD/ TD a 機 械 的 性 質 ASTM 單 位 (Unit) Mechanical 拉 伸 强 度 D-638 Mpa 150 125 160 150 Tensile strength 拉 伸 彈 性 率 D-638 Mpa 11000 17000 11000 10000 Tensile modulus 拉 伸 斷 裂 拉 長 D-638 % 2.2 0.8 1.7 1.6 Tensile elongation at break 布 阿 松 分 配 比 率 ----------- --------------- 0.36 0.35 0.37 0.36 Poisson's ratio 彎 曲 強 度 D-790 Mpa 220 200 220 200 Flexural strength 彎 曲 彈 性 率 D-790 Mpa 10000 16000 10000 9000 Flexural modulus 彎 曲 斷 裂 拉 長 D-790 % 2.7 1.4 2.2 2.0 Flexural elongation at break 擇 錘 式 衝 激 强 度 ( 附 有 / 無 缺 口 ) D-256 J/m 100 / 650 75 / 210 65 / 480 60 / 350 Izod impact strength (notched / un-notched) 壓 縮 強 度 D-695 Mpa 170 150 180 170 Compressive strength 洛 氏 硬 度 , RM D-785 --------------- 121 / 100 121 / 100 121 / 100 118 / 98 Rockwell hardness, R/M 摩 擦 系 數 b , 靜 摩 擦 / 動 摩 擦 ----------- --------------- 0.36 / 0.35 0.36 / 0.35 0.35 / 0.35 0.23 / 0.22 Co-eff. Of friction b , t~0.8mm 熱 的 性 質 ASTM 單 位 (Unit) Thermal 負 載 彎 曲 溫 度 (1.82Mpa) D-648 ℃ 255 265 230 230 Distortion temp. of under load, 1.82MPa 線 熱 膨 脹 系 數 c , -30°-90/℃ D-696 m/mK 2.4 x 10 -5 1.8 x 10 -5 2.3 x 10 -5 2.3 x 10 -5 Co-eff. Of thermal expansion c , -30 to 90℃ d UL 燃 線 性 ,t≒0.8mm UL-94 ------------- V-0 V-0 V-0 V-0 UL Flammability d , t~0.8mm 電 氣 性 質 ASTM 單 位 (Unit) Electrical 絶 緣 破 壞 強 度 t=1.6mm D-149 kv/mm 16 16 16 16 Dielectric strength, t=1.6mm 介 電 常 數 ( 電 容 率 ), 1MHz D-150 ------------- 3 5 4 4 Dielectric constant, 1MHz 介 質 損 耗 角 正 切 , 1NHz D-150 ------------- 0.002 0.007 0.002 0.002 Dissipation factor, 1MHz 耐 統 調 性 (CTI) D-3638 Volt ------------- ------------- ------------- ------------- Comparative tracking index (CTI) 耐 電 弧 性 D-495 Sec. 120 160 120 120 Arc resistance 體 積 固 有 電 阻 D-257 Ohm. Cm 10 16 10 16 10 16 10 16 Volume resistibility 成 形 條 件 ASTM 單 位 (Unit) Moulding Conditions 炮 管 各 溫 度 約 ----------- ℃ 300 - 340 300 - 340 300 - 340 290 - 320 Cylinder temperature 模 具 溫 度 ----------- ℃ 120 - 150 120 - 150 120 - 150 120 - 150 Mould temperature a: MD; 樹 脂 流 動 方 向 , TD; 流 動 中 直 角 方 向 , b: 壓 力 P=150KPa, 速 度 V=0.3m/s, 對 S45C (<strong>PPS</strong> vs. Steel), c: MD 及 TD 的 平 均 值 , d: UL file No. E53829, e: 我 司 數 據 , f: 纖 維 應 力 0.46MPa a: MD; Mould direction, TD; Transverse direction, b: P=150KPa, V=0.3m/s, <strong>PPS</strong> vs. carbon steel, c: Average value of MD & TD, d: UL file No. E53829, e: Own data, f: Fibre stress 0.46MPa.
Table 7 低 鹵 素 <strong>PPS</strong> 系 列 / Low Halogen type <strong>PPS</strong> Series 材 料 編 號 (Grade No.) FZ-4020-A1 FZ-3805-A1 Properties 項 目 構 成 和 特 性 GF 40% GF & 其 他 Other General Information (Properties) (General Information) 低 鹵 素 , 无 铅 锡 焊 低 鹵 素 , 低 翘 曲 Cl;