Download PDF Catalogue - OMS lighting
Download PDF Catalogue - OMS lighting
Download PDF Catalogue - OMS lighting
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Mechanical and<br />
plant engineering<br />
Similarly as in the area of<br />
metal processing, the mechanical<br />
and plant engineering<br />
is typical by its variedness<br />
of activities performed. When<br />
planning the <strong>lighting</strong> system<br />
it is inevitable to take into<br />
consideration the specific<br />
demands they place on the<br />
<strong>lighting</strong> solution.<br />
The area of the mechanical and<br />
plant engineering represents<br />
a whole spectrum of activities<br />
typical in various levels of precisions:<br />
from the basic assembly<br />
through handling with small<br />
components up to the demanding<br />
visual quality control. In<br />
general it can be said that the<br />
more precision demanding the<br />
activity the employee carries out<br />
is, the higher the requirements<br />
on the <strong>lighting</strong> quality are laid.<br />
The European standard<br />
EN 12464-1 states for the<br />
production premises in this line<br />
of business the minimal levels<br />
of the maintained illuminance<br />
from 200 lux to 750 lux in<br />
dependence on the activity realised.<br />
The scientific research and<br />
our experience from practice<br />
confirms that a higher illuminance<br />
level positively affects the<br />
visual and psychological wellbeing<br />
of the employees and<br />
stimulates their performance<br />
efficiency and therefore we also<br />
recommend to maintain higher<br />
illuminance levels in those<br />
spaces where the standard does<br />
not require it.<br />
To achieve the standard stated<br />
values of the minimal maintained<br />
illuminance, it is suitable<br />
to use the linear luminaires with<br />
the direct characteristic of the<br />
luminous flux distribution which<br />
help us gain sufficient quality of<br />
<strong>lighting</strong> uniformity. In the case it<br />
is the assembly line production,<br />
it is recommended to place the<br />
luminaires parallely with the<br />
assembly line.<br />
The construction and technological<br />
parameters of our luminaire<br />
Prestige, which is able to<br />
achieve appropriate illuminance<br />
level with mounting hight up to<br />
12 metres, enable the <strong>lighting</strong><br />
designer to use this <strong>lighting</strong><br />
fixture also in high halls.<br />
By choosing the optimal light<br />
source for this industrial space,<br />
LED light sources could be the<br />
most economical and effective<br />
solution. They achieve high<br />
lifespan values, they are typical<br />
by high efficacy and effectiveness<br />
and due to their low failure<br />
rate and long lifespan they do<br />
not represent any increased<br />
burden from the point of view<br />
of the maintenance costs.<br />
In the spaces that are not defined<br />
as sterile but at the same<br />
time they place large demands<br />
on the workplace cleanliness,<br />
it is necessary to use luminaires<br />
which can be cleaned easily and<br />
which do not contain components<br />
where impurities or dust<br />
is trapped.<br />
The more precision demanding the<br />
activity the employee carries out is,<br />
the higher the requirements on the<br />
<strong>lighting</strong> quality are laid.<br />
In production halls with standard<br />
hight of the walls it is suitable to<br />
use linear luminaires with the direct<br />
characteristic of the luminous flux.<br />
To obtain the standard stated levels<br />
of the maintained illuminance it<br />
production halls with non standard<br />
hight of the walls (6 m and more)<br />
it is important to choose luminaires<br />
that can be used in different<br />
mounting hight<br />
Special requirements on the<br />
<strong>lighting</strong> solution are laid by the<br />
workplaces equipped with the<br />
visual display units (VDU). To<br />
prevent the rise of undesirable<br />
reflections on the screens which<br />
would disturb the employees or<br />
make it impossible to distinguish<br />
the displayed information,<br />
it is suitable to use the<br />
non-glaring luminaires, e.g.<br />
the special computer workstation<br />
luminaires or luminaires<br />
fitted with microprism which is<br />
the most effective method of<br />
spreading the soft diffuse light.<br />
For activities with demanding<br />
visual tasks (e.g. inspection or<br />
handling with small components),<br />
it is recommended to<br />
support the main illumination<br />
with additional table luminaires<br />
in the place of the visual task.<br />
For the inspection activities the<br />
luminaires with a narrow luminous<br />
intensity curve represent a<br />
suitable solution.<br />
prestige 152<br />
RECOMMENDED PRODUCTS<br />
PRESTige LED 151<br />
tornado PC LED 147<br />
tornado PC 147<br />
ux-MYar 146<br />
RECOMMENDED PRODUCTS<br />
GRAFiAS 146<br />
eco BAY 148<br />
ux-BELL 145<br />
Mechanical and plant engineering<br />
72/73