Ultraflux Clamp-on probe SE_1586E2 - hsa-asia.com
Ultraflux Clamp-on probe SE_1586E2 - hsa-asia.com
Ultraflux Clamp-on probe SE_1586E2 - hsa-asia.com
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
PROBE LOCATION<br />
• When possible, locate <strong>probe</strong>s upstream from a hydraulic disturbance..<br />
• When possible, respect following minimum straight length :<br />
10 Ø upstream<br />
3 Ø downstream, Ø means diameter of the pipe .<br />
• In the case of an horiz<strong>on</strong>tal pipe, avoid installing the <strong>probe</strong>s<br />
<strong>on</strong> the top or the bottom part of the pipe because the<br />
risk of bubbles or deposits<br />
On a vertical pipe, there is no restricti<strong>on</strong> for <strong>probe</strong> locati<strong>on</strong>.<br />
• Requested accuracy <strong>on</strong> distance inter-<strong>probe</strong>s : +/- 0,5 mm<br />
• The c<strong>on</strong>verter calculates and displays this distance D.S to be adjusted between <strong>probe</strong>s<br />
around the central zero (see fig 1).<br />
PROBES INSTALLATION<br />
• Clean upthe pipe (rust, roughness). In most cases, the paint doesn’t matter .<br />
• Apply plenty of coupling agent <strong>on</strong> <strong>probe</strong>s face and <strong>on</strong> the pipe wall at the locati<strong>on</strong> .<br />
- Standard coupling gel for temperatures lower than 60°C (during a few hours).<br />
- High temperature special grease for temperatures up to 120°C or l<strong>on</strong>g term use .<br />
- Coupling elastomer, coated <strong>on</strong> both faces with special grease, for very l<strong>on</strong>g term use. It<br />
must be hardly tight.<br />
• The fixing is d<strong>on</strong>e by stretching the elastic around the pipe, or with stainless steel straps for<br />
fixed installati<strong>on</strong> (see fig 1).<br />
CONNECTIONS<br />
• The <strong>probe</strong> holder is equipped of two push-pull c<strong>on</strong>nectors for twinax shielded cables.<br />
• Use the cables re<strong>com</strong>mended by ULTRAFLUX.<br />
• C<strong>on</strong>nect upstream and downstream transducers to c<strong>on</strong>verter using corresp<strong>on</strong>ding inputs .<br />
COMMISSIONING<br />
• A good installati<strong>on</strong> in good site c<strong>on</strong>diti<strong>on</strong> must give a good echo signal and a reliable<br />
measurement result.<br />
• If the acoustic transmissi<strong>on</strong> result through the pipe is too poor (no echo or too high<br />
amplificati<strong>on</strong> gain), proceed as follows :<br />
- Check the distance D.S .between <strong>probe</strong>s .<br />
- Check the coupling agent between the <strong>probe</strong>s and the pipe .<br />
- If fault persists, try at another locati<strong>on</strong> (pipe internally corroded ?).<br />
- If no result, try with lower frequency transducers .<br />
- If liquid is flowing bubbles, try to improve these c<strong>on</strong>diti<strong>on</strong>s.<br />
FS210A GB1 04/10/04 page 2/2<br />
________________________________________________________________________________________________<br />
ULTRAFLUX Le Technoparc - 17, rue C. E. Jeanneret 78306 POISSY Cedex - France<br />
Tél. +33 (0)1 39 79 26 40 - Fax +33 (0)1 39 79 91 22 - e-mail : ultraflux@ultraflux.fr - http://www.ultraflux.<strong>com</strong>