DYMAX ADHESIVE Product Data Sheet - Blaze Technology Pte Ltd.
DYMAX ADHESIVE Product Data Sheet - Blaze Technology Pte Ltd.
DYMAX ADHESIVE Product Data Sheet - Blaze Technology Pte Ltd.
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
BLAZE TECHNOLOGY PTE LTD<br />
<strong>DYMAX</strong> <strong>ADHESIVE</strong><br />
<strong>Product</strong> <strong>Data</strong> <strong>Sheet</strong><br />
<strong>DYMAX</strong> ® 910, 911 & 912<br />
<strong>ADHESIVE</strong>S FOR WIRE & PARTS TACKING<br />
INTRODUCTION<br />
Dymax UV curing tacking adhesives have been formulated to cure rapidly under longwave (365 nm) UV light at intensities above<br />
20 mW/cm 2 . Dymax 910, 911 and 912 have been designed for wire and parts tacking on printed circuit boards. Dymax UV<br />
curing adhesives can also be used for a wide variety of strain relief and wire unitization applications. These products withstand<br />
thermal shock from soldering while resisting brief solvent and aqueous washes. Dymax wire tacking adhesives are thixotropic<br />
and designed for easy dispensing, yet they resist migration on the part.<br />
DESCRIPTIONS<br />
Light Weld 910 is typically used as a flexible wire and parts tacking adhesive. While possessing high adhesion to boards and<br />
electronic parts, a tack can be mechanically removed. Heating the tack to 200°F or more facilitates removal.<br />
Multi-Cure 911 is specially designed to provide rapid, structural wire tacking of PCB’s. Cure occurs with UV light or in<br />
combination with heat. Multi-Cure 911 has excellent adhesion to wide variety of surfaces.<br />
Light Weld 912 has been formulated to cure rapidly under longwave UV light. <strong>Product</strong> 912 is designed for wire tacks on PCB’s,<br />
withstands thermal shock from solder while resisting most solvent and aqueous washes.<br />
*Meets Belcore TR-NWT-000078<br />
UNCURED PROPERTIES<br />
Solvent Content<br />
Chemical Class<br />
Appearance<br />
Flash Point<br />
Solubility<br />
Toxicity<br />
Viscosity<br />
None, 100% solids<br />
Urethane (Meth) Acrylate<br />
Light Straw<br />
>200°F (95°C)<br />
Alcohols/Chlorinated Solvents<br />
Low<br />
Non flowing Thixotropic Paste<br />
CURED PROPERTIES<br />
910 911 912<br />
PHYSICAL<br />
Durometer Hardness A60 D75 D85<br />
UV Cured Film Thickness 0.5” 0.15” 0.25”<br />
Thermal Limit (brittle/degrades) -50/300°F -45/300°F -40/250°F<br />
Tensile Strength Glass-to-Steel 500 psi 3,000 psi 2,500 psi<br />
Linear Coefficient of Expansion (in/in/°Cx10 -6 ) 118 90 90<br />
Dielectric Strength (Volts/mil) 500 1,600 1,800<br />
Surface Resistivity (10 12 Ohm) 60 230 380<br />
Dielectric Constant at 1MHz 3.27 4.10 3.41<br />
Dissipation Factor at 1MHz 0.05 0.06 0.03<br />
CURE DATA<br />
910 911 912<br />
Time to Full Cure*
BLAZE TECHNOLOGY PTE LTD<br />
<strong>DYMAX</strong> <strong>ADHESIVE</strong><br />
<strong>Product</strong> <strong>Data</strong> <strong>Sheet</strong><br />
<strong>DYMAX</strong> 910, 911, 912, 3/99<br />
Activator Cure - Multi-Cure 911 Only<br />
Fixture<br />
15-30 Seconds<br />
5 Minutes 250 psi<br />
10 Minutes 500 psi<br />
1 Hour 1,600 psi<br />
24 Hours 2,900 psi<br />
On Part Life of Activator: Activator will lose potency after eight hours. Activator must be kept in closed metal containers when<br />
not in use. Exposure to oxygen will increase fixture time.<br />
INSTRUCTIONS FOR USE<br />
1. Apply Activator over one of the surfaces to be bonded. Allow for the solvent to evaporate, if needed. Surface will have an<br />
oily appearance.<br />
2. Apply only a single drop of bead of adhesive to the center of the mating surface. DO NOT SPREAD OVER THE BOND<br />
SURFACE.<br />
3. Assemble parts and clamp or hold immobilized until fixture occurs (30-60 seconds). DO NOT stress bonds until sufficient<br />
strength has been achieved. (This may be up to several minutes depending on requirements).<br />
NOTE: Adhesive will not cure unless thoroughly mixed with Activator. If wet/tacky adhesive is present outside of joint, it can<br />
be cured with heat or cleaned away with recommended solvents.<br />
DISPENSING AND HANDLING <strong>ADHESIVE</strong><br />
Dymax 910, 911, and 912 is available in various packages such as syringes, cartridges, bottles, and pails. It may be dispensed<br />
with a variety of automatic bench-top syringe applicators or other equipment as required. Direct questions relating to dispensing<br />
and curing systems for specific applications to Dymax Technical Representatives.<br />
Wear impervious gloves and/or barrier cream. Repeated or continuous skin contact with liquid adhesive will cause irritation and<br />
should be avoided. Do not wear absorbent gloves. Remove adhesive from skin with soap and water. Never use solvents to<br />
remove adhesive from skin or eyes.<br />
STORAGE AND SHELF LIFE<br />
Store material in cool dark place when not in use. Do not expose to UV light or sunlight. Material may polymerize upon<br />
prolonged exposure to ambient light. Replace lid immediately after use. <strong>Product</strong> has a one-year shelf life when stored below<br />
90°F in the original, unopened container. Refrigerated storage extends shelf life.<br />
CAUTION<br />
For industrial use only. Avoid breathing vapors. Avoid contact with eyes and clothing. In case of contact, immediately flush with<br />
water for at least 15 minutes; get medical attention. Wash clothing before reuse. Keep out of reach of children. Do not take<br />
internally. If swallowed, induce vomiting at once and call a physician. Repeated or continuous skin contact with liquid adhesive<br />
will cause irritation and should be avoided. For specific information, refer to the product Material Safety <strong>Data</strong> <strong>Sheet</strong>.<br />
© 1997, 1998 Dymax Corporation<br />
MD® Medical Device Adhesives is also a registered trademark of Dymax Corporation<br />
The data contained in this bulletin which represents typical results, is furnished for information only, and is believed to be reliable. We cannot assume responsibility for results obtained by others over whose<br />
methods we have no control. It is the user's responsibility to determine suitability for the user's purpose of any product or method mentioned herein and to adopt such precautions as may be advisable for the<br />
protection of property and persons against any hazards that may be involved in the handling and use thereof. Nothing in this bulletin is to be interpreted as a representation of freedom from domination of patents<br />
owned by others or a license under a Dymax Corporation patent. We recommend that each prospective user test the proposed application before repetitive use, using the data as a guide. For specific information,<br />
refer to Material Safety <strong>Data</strong> <strong>Sheet</strong> before use.<br />
<strong>DYMAX</strong> CORPORATION * 51 GREENWOODS ROAD * TORRINGTON, CT 06790 * TEL: 860-482-1010 * FAX: 860-496-0608<br />
<strong>DYMAX</strong> EUROPE GMBH * TRAKEHNER STRASSE 3 * D-60487 FRANKFURT a.M. GERMANY * TEL: 49-69-7165-3568 * FAX: 49-69-7165-3830<br />
Dymax, Light Weld, Light-Welder, Ultra Light-Weld and Multi-Cure are registered trademarks of Dymax Corporation<br />
<strong>DYMAX</strong> USA E-Mail: info@dymaxcorp.com * Internet: http:\\www.dymax.com * <strong>DYMAX</strong> EUROPE E-Mail: dymaxinfo@dymax.de<br />
For Local Support Singapore 65 6270 2188 Malaysia 604 390 5882 Thailand 66 2361 2926 Email sales@blazeasia.com www.blazeasia.com
Change language