Trus Joist Framers Handbook.pdf
Trus Joist Framers Handbook.pdf
Trus Joist Framers Handbook.pdf
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
ALLOWABLE HOLES<br />
2<br />
1.55E TimberStrand ® LSL Headers and Beams<br />
1⁄3 depth<br />
2 x diameter of the largest hole (minimum)<br />
Allowed hole zone<br />
GENERAL NOTES<br />
■<br />
Round holes only.<br />
Other iLevel ® <strong>Trus</strong> <strong>Joist</strong> ® Headers and Beams<br />
1.3E<br />
TimberStrand ® LSL<br />
hole zone<br />
8" 8"<br />
■<br />
No holes in headers or beams in plank orientation.<br />
Microllam ® LVL and<br />
Parallam ® PSL hole zone<br />
2 x diameter of<br />
the largest hole<br />
(minimum)<br />
1 ⁄3 depth<br />
■<br />
Header and<br />
Beam<br />
Depth<br />
Maximum<br />
Round Hole<br />
Size<br />
91⁄4"–91⁄2" 3"<br />
111⁄4"–11 7 ⁄8" 3 5 ⁄8"<br />
14"–16" 4 5 ⁄8"<br />
<br />
See illustration for<br />
allowed hole zone.<br />
DO NOT cut, notch, or drill<br />
holes in headers or beams<br />
except as indicated in the<br />
illustrations and tables.<br />
d<br />
d<br />
Microllam ® LVL and<br />
Parallam ® PSL<br />
allowed hole zone<br />
middle 1 ⁄3 span<br />
1.3E TimberStrand ® LSL allowed hole zone<br />
d<br />
■<br />
Header and<br />
Beam<br />
Depth<br />
Maximum<br />
Round Hole<br />
Size<br />
4 3 ⁄8" 1"<br />
51⁄2" 1 3 ⁄4"<br />
71⁄4"–20" 2"<br />
<br />
See illustration for<br />
allowed hole zone.<br />
GENERAL NOTES<br />
■<br />
Allowed hole zone suitable for uniformly<br />
loaded headers and beams only.<br />
■<br />
Round holes only.<br />
TimberStrand ® LSL Wall Studs<br />
■<br />
No holes in cantilevers.<br />
■<br />
No holes in headers or beams in plank<br />
orientation.<br />
The notch shown may be cut anywhere except the middle 1 ⁄3 of the length of the stud.<br />
One hole may be drilled anywhere along the length of the stud or column but must be at least 5 ⁄8" from the edge.<br />
5⁄8" minimum edge distance Maximum notch:<br />
7⁄8" for 3 1 ⁄2" thick walls<br />
Maximum diameter:<br />
1 3 ⁄8" for 3 1 ⁄2" thick walls<br />
2 3 ⁄16" for 5 1 ⁄2"–11 1 ⁄4" thick walls<br />
1 3 ⁄8" for 5 1 ⁄2"–11 1 ⁄4" thick walls<br />
DO NOT cut a notch<br />
and a hole in the<br />
same cross section.