Unipress Vario E.qxd:Unipress Vario E.qxd

More documents

Recommendations

Info

5. Shipping and Installation of Machines 5-001 Transport The Unipress / Unipress - Vario shall be delivered on fastened on a pallet with a cardboard cover. Upon request, the Unipress can also be packed in a stabile wooden crate. Wood pallets and wooden crates can be transported without problems by a low lift platform truck or a fork lift truck. The machine must be protected during the transport and storage from moisture and wetness. Storage temperature should be between -20¯ and 50¯. Operating temperature should be between 10¯ and 40¯. Center of gravity 5-002 Space Requirements The space requirement depends on the side of the work pieces. The minimal depth dimensions are about 200 cm. The minimal width dimensions are about 80 cm, and additionally 100 cm for each extension bar and side. The machine must be kept in a dry room away from moisture and wetness. The surrounding temperature of the operating machine should be between +10¯C to +40¯C. The relative humidity should not exceed 85% if at all possible. Various malfunctions with the machine may occur with large deviations in the environmental conditions. 5-003 Installation in Designated Space The machine can be lifted on the machine table and on the machine frame. We recommend screwing the machine with the provided bore holes on the machine table on a base. Page 34 The star in your cabinet 250 340 Illustration 5-001-01
6-001 Pneumatic connection The star in your cabinet 6. Start-Up The machine has a 2 meter long air hose that has a diameter of 6/3. A Euro-Quick coupler plug is installed corresponding to the voltage in the country of destination. See Chapter 4-007 for the wiring diagram. a) Turn the regulator knob of the service unit counter clockwise. b) Connect the pneumatic air. The pneumatic air supply should only be accessible to maintenance personnel The quick coupling or a stop valve with ventilation shall be connected to the compressed air ductwork system. c) Turn the regulator knob clockwise until the pressure gauge pointer shows approximately 0.55 - 0.6 MPa (0.55 - 0.6 bar). d) Conduct the function test without drilling bits and with the main switch off. When the start button is pressed, the motor descends. When the hand is removed from the start button, the machine must return immediately to the original position. e) Check the work piece holding clamps, if included (accessories). 6-002 Electric connection The electric connection must be done by an authorized specialist and must meet local specifications. See Chapter 4-008 for the wiring diagram. The machine has a 2 meter long 5 -pole rubber cable. If necessary, according to the destination country, a 5-pole CEE 16A plug will be installed. If necessary, corresponding and available wall sockets are provided so the connection can be made by the customer. Start the machine as described in 6-001. Engage the main switch and press the start button (without the drill bits being connected) until the machine has reached its lowest point and the motor engages. Remove the hand from the start button and determine the rotation direction through the ventilation grid. Controlling the rotation direction: the rotation direction must conform to the arrow on the ventilation cover. A change in the rotation direction can only be performed by a specialist! 6-003 Other connections Dust collection connection O 80 mm Required suction power about 2000 m h The Unipress must not be run without the dust collection system operating. See Chapter 3-001 "Dust and Noise Emissions Ratings". Page 35
Page 1 and 2: OPERATING INSTRUCTIONS Grass Unipre
Page 3 and 4: The star in your cabinet Table of c
Page 5 and 6: 1-001 List of Illustrations 1. Gene
Page 7 and 8: 2-001 Safety Information 2. Safety
Page 9 and 10: 2. Safety Information Risk of Impac
Page 11 and 12: 3-004 Variations The Unipress is av
Page 13 and 14: 3-006 Standard Accessories For Unip
Page 15 and 16: 3-006 Standard Accessories 3. Produ
Page 17 and 18: 4. Machine-Parts Description 4-001
Page 19 and 20: 4-002 Description of the Individual
Page 21 and 22: 4-002 Description of the Individual
Page 31 and 32: 4-006 Machine's Function 4. Machine
Page 33: 4-009 Electric Wiring Diagram Illus
Page 37 and 38: 7-1 Requirements for Operators 7. O
Page 39 and 40: 7. Operating the Unipress/Unipress
Page 55 and 56: 7-5 Examples of Usage 7. Operating
Page 73 and 74: 8. Trouble Shooting and Problem Sol
Page 75 and 76: 8. Trouble Shooting and Problem Sol
Page 77 and 78: 10-001 Guarantee Certificate The st
Page 79 and 80: 10-002 Disposal Form The star in yo
Page 81 and 82: 10-003 Resale From Seller: The star
Page 83 and 84: 10-004 Questionnaire 1: Reason for
Page 85 and 86:
10-005 Questionnaire 2: Satisfactio
Page 87 and 88:
NOTES
Page 89 and 90:
WORLDWIDE DISTRIBUTORS Internet: ww
show all

Unipress Vario E.qxd:Unipress Vario E.qxd

Create successful ePaper yourself

Delete template?

Save as template?