Unipress Vario E.qxd:Unipress Vario E.qxd

More documents

Recommendations

Info

8. Trouble Shooting and Problem Solving Illustration 8-001-01 Illustration 8-002-01 Page 72 The star in your cabinet
8. Trouble Shooting and Problem Solving 8-001 Incorrect Drilling Distance - Adjustment of Scale Illustration 8-001-01 -Mount gearbox, if necessary, according to point 7-201 or 7-301. -Mount a drill bit, if necessary, according to point 7-202 or 7-302. -Follow safety information and guidelines. -Place a sample work piece. -Press against the depth stops on fence. -Drill one hole. -Measure drilling distance and compare with the set number on the scale. -If the numbers are not identical, loosen both screws "1" with 4 mm Allen wrench, move the measuring scale to measured number, then tighten both screws "1". -Repeat drilling cycle and compare boring distance again with the number on the scale. 8-002 Incorrect Drilling Depth - Adjustment of Scale Illustration 8-002-01 -Place the sample material on machine table. -Loosen clamp screw "1". -Adjust material thickness according to point 7-401. -Lift the adjustment screw "2", then place the material "3" , which is as thick as the desired drilling depth, underneath. -Drill a sample cycle. In this position the drill bit cutters should just drill the material (leaving obvious marks on the material). -If the drilling is too deep, the adjustment screw must be turned clockwise (1 turn = 1 mm). -If the drill cutters do not reach the material surface, adjustment screw "2" must be turned counter clockwise. -Repeat sample drilling and corrections until the drill cutters drill the material correctly. -Remove the work material "3". The material thickness, according to scale "4", must agree with the actual material thickness. -In case of discrepancies, loosen both screws "5" with 2.5 mm Allen wrench. Move the measuring scale until the measured material thickness is identical with the material thickness shown on scale "4". Tighten both screws "5". The star in your cabinet Page 73
Page 1 and 2:
OPERATING INSTRUCTIONS Grass Unipre
Page 3 and 4:
The star in your cabinet Table of c
Page 5 and 6:
1-001 List of Illustrations 1. Gene
Page 7 and 8:
2-001 Safety Information 2. Safety
Page 9 and 10:
2. Safety Information Risk of Impac
Page 11 and 12:
3-004 Variations The Unipress is av
Page 13 and 14:
3-006 Standard Accessories For Unip
Page 15 and 16:
3-006 Standard Accessories 3. Produ
Page 17 and 18:
4. Machine-Parts Description 4-001
Page 19 and 20:
4-002 Description of the Individual
Page 21 and 22: 4-002 Description of the Individual
Page 23 and 24: 4. Machine-Parts Description 4-003
Page 31 and 32: 4-006 Machine's Function 4. Machine
Page 33 and 34: 4-009 Electric Wiring Diagram Illus
Page 35 and 36: 6-001 Pneumatic connection The star
Page 37 and 38: 7-1 Requirements for Operators 7. O
Page 39 and 40: 7. Operating the Unipress/Unipress
Page 55 and 56: 7-5 Examples of Usage 7. Operating
Page 71: 7-5 Examples of Usage 7. Operating
Page 75 and 76: 8. Trouble Shooting and Problem Sol
Page 77 and 78: 10-001 Guarantee Certificate The st
Page 79 and 80: 10-002 Disposal Form The star in yo
Page 81 and 82: 10-003 Resale From Seller: The star
Page 83 and 84: 10-004 Questionnaire 1: Reason for
Page 85 and 86: 10-005 Questionnaire 2: Satisfactio
Page 87 and 88: NOTES
Page 89 and 90: WORLDWIDE DISTRIBUTORS Internet: ww
show all

Unipress Vario E.qxd:Unipress Vario E.qxd

Create successful ePaper yourself

Delete template?

Save as template?