weathershield multi-surface fungicidal wash 803 - Dulux Trade
weathershield multi-surface fungicidal wash 803 - Dulux Trade
weathershield multi-surface fungicidal wash 803 - Dulux Trade
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Issued 02/14<br />
WEATHERSHIELD MULTI-<br />
SURFACE FUNGICIDAL WASH <br />
<strong>803</strong><br />
<br />
Weathershield Multi-Surface Fungicidal Wash from <strong>Dulux</strong> <strong>Trade</strong> is designed for<br />
cleaning all bare or painted wood and masonry <strong>surface</strong>s contaminated with moulds,<br />
algae and lichen. Suitable for brush application only.<br />
KEY BENEFITS<br />
• Ready for Use<br />
• Kills Algae & Mould Growth<br />
• For Wood & Masonry Surfaces<br />
PRODUCT INFORMATION<br />
Typical Use<br />
Suitable for use on wood and masonry <strong>surface</strong>s.<br />
Pack Size<br />
5L.<br />
Colour Range<br />
Clear liquid.<br />
Film Properties<br />
N/A.<br />
Composition (nominal)<br />
Active Ingredients: Benzalkonium Chloride.<br />
Solvent: Water.<br />
Volume Solids<br />
3% (nominal).<br />
SURFACE PREPARATION<br />
For the best results, remove as much mould algae<br />
or lichen as possible by scraping and brushing,<br />
before treating. Weathershield Multi-Surface<br />
Fungicidal Wash will only be effective on <strong>surface</strong><br />
growths. Where old growths have been trapped<br />
between previous coats, all existing coatings need<br />
to be removed. Special precautions should be<br />
taken during <strong>surface</strong> preparation of pre-1960s paint<br />
<strong>surface</strong>s over wood and metal as they may contain<br />
harmful lead.<br />
SYSTEMS INFORMATION<br />
SHAKE THOROUGHLY BEFORE USE. Apply by<br />
brush to all affected areas. Leave for 24 hours then<br />
thoroughly rinse and scrub with water to remove<br />
residues and dead growth; failure to do this may<br />
result in discolouration of subsequently applied<br />
coatings. Repeat the process if necessary. On<br />
badly affected areas or where lichen is present, the<br />
use of high pressure water-hosing may be<br />
necessary to remove all organic growth completely.<br />
Do not apply in wet weather.<br />
APPLICATION METHOD<br />
Brush only.<br />
Health, Safety & Environmental Information:<br />
Contains quaternary ammonium compounds, benzyl-C8-<br />
18-alkyldimethyl, chlorides. Causes serious eye irritation.<br />
Causes skin irritation. Keep out of reach of children. If<br />
medical advice is needed, have product container or label<br />
at hand. Do not get in eyes, on skin, or on clothing. Wash<br />
hands thoroughly after handling. Call a POISON CENTER<br />
or doctor/physician if you feel unwell. Dispose of contents<br />
and container in accordance with all local, regional,<br />
national or international regulations. Avoid the inhalation<br />
of dust. Wear suitable face mask if dry sanding. Special<br />
precautions should be taken during <strong>surface</strong> preparation of<br />
pre-1960s paint <strong>surface</strong>s over wood and metal as they<br />
may contain harmful lead. CONTAINS BENZALKONIUM<br />
CHLORIDE 2.25% w/w.<br />
Statutory conditions relating to use: FOR USE ONLY<br />
AS A SURFACE BIOCIDE AND WOOD PRESERVATIVE.<br />
Apply by brush at a rate of up to 1 litre of product per 25<br />
square metres of <strong>surface</strong>. Wear suitable protective<br />
clothing and suitable gloves. DO NOT CONTAMINATE<br />
FOODSTUFFS, EATING UTENSILS OR FOOD CONTACT<br />
SURFACES. This material and its container must be<br />
disposed of in a safe way. UNPROTECTED PERSONS<br />
AND ANIMALS SHOULD BE KEPT AWAY FROM<br />
TREATED AREAS FOR 48 HOURS OR UNTIL SURFACES<br />
ARE DRY. COVER WATER STORAGE TANKS before<br />
application. DO NOT USE NEAR DRAINS, PREVENT ANY<br />
SURFACE RUN-OFF FROM ENTERING DRAINS.<br />
REMOVE OR COVER FISH TANKS AND BOWLS before<br />
application. This product contains substances which are<br />
known to be hazardous to the environment. Do not<br />
contaminate ground, waterbodies or watercourses with<br />
chemicals or used container. ALL BATS ARE<br />
PROTECTED UNDER THE WILDLIFE AND<br />
COUNTRYSIDE ACT 1981. BEFORE TREATING ANY<br />
STRUCTURE USED BY BATS, CONSULT NATURAL<br />
ENGLAND NATURE, SCOTTISH NATURAL HERITAGE<br />
OR THE COUNTRYSIDE COUNCIL FOR WALES.<br />
ADDITIONAL PRECAUTIONS FOR PROFESSIONAL<br />
OPERATORS: The (COSHH) Control of Substances<br />
Hazardous to Health Regulations 2002 may apply to the<br />
use of this product at work. Engineering control of<br />
operator exposure must be used where reasonably<br />
practicable in addition to the items of personal protective<br />
equipment. However, engineering controls may replace
WEATHERSHIELD MULTI-<br />
SURFACE FUNGICIDAL WASH<br />
<strong>803</strong><br />
personal protective equipment if a COSHH assessment<br />
shows they provide an equal or higher standard of<br />
protection. AVOID EXCESSIVE CONTAMINATION OF<br />
COVERALLS AND LAUNDER REGULARLY. READ ALL<br />
PRECAUTIONS BEFORE USE. HSE No 6823.<br />
Precautions: WASH ANY CONTAMINATION from skin or<br />
eyes immediately. WASH HANDS AND EXPOSED SKIN<br />
before meals and after use. Keep in the original container.<br />
Keep container tightly closed. KEEP IN A SAFE PLACE.<br />
To avoid risks to man and the environment, comply with<br />
the instructions for use. This product is approved under<br />
The Control of Pesticides Regulations 1986 (as amended)<br />
for use as directed. HSE No. 6823. Ingredients to be<br />
disclosed in accordance with Regulation (EC) No<br />
648/2004 on detergents: Less than 5% - Cationic<br />
Surfactants.<br />
Practical Coverage<br />
A guide to the practical coverage which can be<br />
achieved under normal conditions is up to 25m² per<br />
litre. This will vary considerably depending on the<br />
absorbency of the <strong>surface</strong>.<br />
Thinning<br />
N/A.<br />
Drying Times<br />
Single coat at standard thickness:<br />
Touch Dry: 2-4 hours. Leave on the <strong>surface</strong> for 24<br />
hours, then rinse with clean water to remove dead<br />
growth/residues.<br />
Cleaning Up<br />
After use, remove as much product as possible<br />
from equipment before cleaning with water.<br />
Transportation & Storage<br />
Do not use or store in extremes of temperature and<br />
protect from frost. To prevent spillage, please store<br />
and transport upright.<br />
VOC<br />
N/A.<br />
<br />
Spray Recommendations<br />
This product should not be sprayed.<br />
FURTHER SUPPORT<br />
If you need further support, please contact the AkzoNobel Technical Advice Centre on 08444 817 818.<br />
Use biocides safely. Always read the label and product information before use.<br />
Always read full Health, Safety & Environmental Information on can before use.<br />
Safety datasheet (SDS <strong>803</strong>) is available free on request by telephoning the AkzoNobel Technical Advice Centre<br />
or by visiting duluxtrade.co.uk.<br />
AkzoNobel, the AkzoNobel logo, the Flourish logo, <strong>Dulux</strong> <strong>Trade</strong>, Weathershield and the Planet Possible logo are trademarks of<br />
the AkzoNobel group. © AkzoNobel 2014.