DUCTGARD - Gilberts (Blackpool)

More documents

Recommendations

Info

Mode 9DescriptionMode 9 is a fully automatic type of smoke andfire damper and operates on the basis of failsafe closure with automatic reset. It has beendesigned to close in smoke and fire conditionsupon a failure of the supply voltage to the motoror in the event of an electro thermal fusible linkseparating at a pre-determined temperature(72°C standard). Volt free microswitches areincluded as standard.OperationMode 9 is fitted with a spring return square drivemotor which will hold the damper open for aslong, as the supply voltage is available.Interruption of this supply will cause controlleddamper closure by way of the motors springreturn operation. In addition however, thedamper is fitted with an electro thermal fusiblelink which will fail at a pre-determinedtemperature (72°C standard) and close thedamper irrespective of the status of the motor.An integral test pushbutton on the electrothermal fuse housing allows for the local testingof the damper operation.Motor Control OptionsA: 24V AC or DC supply.B: 240V AC supply.Note: All options are complete with positionmicroswitches as standard.Re-set ProcedureProvided the fusible link is intact the damper willautomatically reset after an interruption of thesupply voltage to the motor. The motor will takeapproximately 80 seconds to open the damper.The spring return motor and terminal box (iffitted) are mounted on the ductwork connectionsleeve. Fully assembled prior to despatch theyrequire only the external electrical connectionsto be made.Mode 10Mode 10 performs in exactly the same manneras the Mode 9 except that the operation isreversed and the unit is fail safe open. Themotor sets the unit in the full closed position andthe unit will only open in the event of a aninterruption of the supply voltage to the motor orseparation of the thermal fusible link.Ordering procedure: Back coverOPTIONAL FEATURES■ A RANGE OF ELECTRO-MECHANICAL CONTROL PANELS■ VOLT FREE CONTACTS FOR REMOTE INTERFACE■ REMOTE, ELECTRICAL BLADE STATUS INDICATION PANELS■ DAMPER MOUNTING TERMINAL BOX FOR MICROSWITCHAND/OR MOTOR CABLING■ HEVAC INSTALLATION FRAME/DRY WALL FIXING FRAME■ ACCESS PANELS5
DimensionalDataDampers OnlyDampers with Installation FramesSquare and Rectangular Spigots . . .Ref SSmaller and intermediate sizes available41List Width - 393Dim 'A'12140List Width + 19925 25Units supplied with 40mmdeep spigots for rivettingor self tapping intoductwork system.List Size Range200 - 1000 WIDE in 50mmincrements100 - 1000 HIGH in 100mmincrementsDim 'A'Modes,9,10 140Above with terminalbox 240Modes 5,6 240Circular Spigots . . . . . . . . . . . . . . . . .Ref CMode 9 & 1041140List Diameter - 3 93121Smaller and intermediate sizes availableList Diameter + 19950 2525Units supplied with 40mmdeep circular spigots forrivetting or self tapping intoductwork system.List Size Range200 - 1000 Diameter in 100mmincrementsFor other circular duct sizes, overallsizes as next size up standard size.For example, 315 duct has 312spigots and 432 high casing25Circular Spigots . . . . . . . . . . . . . . .Ref CMode 1, 2, 5 & 641List Diameter - 39350 50242 121Smaller and intermediate sizes availableList Diameter + 199252541List Height + 147412541List Height + 14741252541List Height - 3List Height + 1474125Units supplied with 40mm deepcircular spigots for rivetting orself tapping into ductworksystem.List Size Range200 - 1000 Diameter in 100mmincrementsFor other circular duct sizes, overallsizes as next size up standard size.For example, 315 duct has 312spigots and 432 high casing256
Page 1 and 2: DUCTGARDDuct MountingSmoke andFire
Page 3 and 4: The Gilbert’s 2007 Ductgardpresen
Page 5: Mode 5DescriptionMode 5 is a fully
Page 9 and 10: InstallationFramesHEVAC Installatio
Page 11 and 12: Modes 9/10Mode 9 and 10 Ductgards i
Page 13 and 14: AncillaryItemsGilberts range of anc
Page 15 and 16: Operation &MaintenanceInstructionsO

DUCTGARD - Gilberts (Blackpool)

Create successful ePaper yourself

Delete template?

Save as template?