3DQuickMold Training Manual - 3D CAD/CAM Design Software

More documents

Recommendations

Info

Auto Inserts:Click this icon, the following dialogue box pop out, click Yes to paste definedinsert bodies onto the existing Insert file one by one.Finally, Click OK,the bodies will then be pasted to the selected target component.4.8 3DQuickMold UpdateClickto update the part or assembly if the cavity patch body, cavity insertbody, core patch body, or core insert body is changed.4.9 Continuous EdgesThis is a tool for searching of edges, through difference combination ofselected faces and edges(there are three combination,three corresponding usage),quicksearches of all desired edges, select face first then edges,click Continuous Edges to proceedwith the search.Usage 1:select one face (or more than one continuous face), on this faces select an edge,clickContinuous Edges,3DQuickMold will search for a close loop among multiple faces. Normally,the parting lines are many but they belong to a few faces only, in this case, to avoid missing thesmall edge selection, this tool could be used.Select two faces and one edge as the following picture shown. Click Continuous Edges, theresulting edges are highlighted as below. It is a complete loop.31
Usage 2:select one or more adjacent faces, on this faces select any two edges, clickContinuous Edges,3DQuickMold will search a partial open loop, the direction of the openloop will follow the first picking up point on the first edges.If the picking up point on the first selected edge is near to the top end, the partial open loop isselected as the below picture shown.4.10 Box SelectionThis is a tool for searching of faces,through a space box defined by someentities, all the faces fully enclosed by the box will be selected,it is commonly used insearching faces for the side core, inserts and electrode. Using these tools, users can avoid themissing of small faces by mouse click selection.32
Page 1 and 2: 3D QuickTools LimitedConcept & Tuto
Page 3 and 4: 4.11 Face Search ..................
Page 5 and 6: 14.3 Holder........................
Page 7 and 8: Each mold design module is listed b
Page 9 and 10: Chapter 1.Set ProjectThis is not a
Page 11 and 12: 3.1 WorkpieceWorkpiece is used to d
Page 13 and 14: 3.2 Search Cavity/Core facesThis is
Page 15 and 16: 3.3 Extract parting linesOnce the c
Page 17 and 18: Note: The Shut-off surface feature
Page 19 and 20: Radiate surface:Select the referenc
Page 21 and 22: Please ensure the pre-selected core
Page 23 and 24: Chapter 4.QM-SolidPartingSolid Part
Page 25 and 26: Extend by distance: Extend the sele
Page 27 and 28: Revolved faces: Select revolved fac
Page 29 and 30: There are two ways to define the pa
Page 31: After the setting is completed, cli
Page 35 and 36: Searching sample with different opt
Page 37 and 38: Select a face or edge on body, clic
Page 39 and 40: 5.2 bodyThis functions works on par
Page 41 and 42: :Using sketch to define the insert
Page 43 and 44: AdvancedClick the Advanced button o
Page 45 and 46: :Select the rectangular face and an
Page 47 and 48: :Rectangular insert holder.:Bottom
Page 49 and 50: Insert name and material can be spe
Page 51 and 52: :Double flange on the insert. Selec
Page 53 and 54: 6.2 ToolsList the existing runners
Page 55 and 56: Activate the Tools page, click, the
Page 57 and 58: :Select the orgin and a point on an
Page 59 and 60: :Select the orgin and a point on an
Page 61 and 62: :Select a sketch line or connected
Page 63 and 64: :Select a reference plane to be the
Page 65 and 66: 2. Side gate:Select a sketch point
Page 67 and 68: Chapter 7.Layout ManagerLayout Mana
Page 69 and 70: If nothing is pre-selected, 3DQuick
Page 71 and 72: Click Apply once the setting is don
Page 73 and 74: Duplicate:Duplicate the selected ca
Page 75 and 76: H1 (cavity): Define the thickness o
Page 77 and 78: Show bitmap: Show bitmap near the d
Page 79 and 80: Reverse hide:Show only the selected
Page 81 and 82: Add/Remove: Add or remove selected
Page 83 and 84:
Chapter 9.Ejector WizardEjector Wiz
Page 85 and 86:
Select point, edge or face to defin
Page 87 and 88:
Decimal places:From 0 to 4, user ca
Page 89 and 90:
Position ejector:Select the sketch
Page 91 and 92:
:Stepped ejector, :Ejector blade, :
Page 93 and 94:
Clearance height:The Clearance heig
Page 95 and 96:
:Select the planar face where the e
Page 97 and 98:
Clearance height:Select this will i
Page 99 and 100:
Chapter 10. Cooling WizardThe uses
Page 101 and 102:
:Pick up one face, a sketch line en
Page 103 and 104:
Methods available for creating the
Page 105 and 106:
Use Solidworks sketch utilities to
Page 107 and 108:
10.3 ParametersIt is for building t
Page 109 and 110:
Select a sketch point on the coolin
Page 111 and 112:
10.4 AccessorySome typical standard
Page 113 and 114:
After cooling channel is created, u
Page 115 and 116:
To add a screw, select a type, a pa
Page 117 and 118:
:mate reference. It could be the sp
Page 119 and 120:
Chapter 12.Slider WizardCustomer ca
Page 121 and 122:
: Slider body type 2Method: same as
Page 123 and 124:
: Slot type 3 for connection of sli
Page 125 and 126:
Method: select a face and an edge a
Page 127 and 128:
:Open direction, select planar face
Page 129 and 130:
13.2 BodyThere are some tools for c
Page 131 and 132:
:Extend lifter body to the selected
Page 133 and 134:
The following five icons are applic
Page 135 and 136:
After selecting two faces, click ea
Page 137 and 138:
: Guide plate. Select a inclined fa
Page 139 and 140:
Simulate: Lifter animation function
Page 141 and 142:
14.2 BodyThe functions on this page
Page 143 and 144:
Select four edges as the following
Page 145 and 146:
Selection:Select sketch on the part
Page 147 and 148:
:Prefix for the electrode bodyClick
Page 149 and 150:
Click OK, an electrode holder is cr
Page 151 and 152:
:Copy body, select a face on the ex
Page 153 and 154:
Angle/Z:Angle value between the nor
Page 155 and 156:
16.6 Create PocketCreate pockets fo
Page 157 and 158:
16.9 Set configurationIn a multiple
Page 159 and 160:
16.10 Save projectSave the entire a
show all

3DQuickMold Training Manual - 3D CAD/CAM Design Software

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?