3DQuickMold Training Manual - 3D CAD/CAM Design Software

More documents

Recommendations

Info

:Select a reference plane and a face on the part, an extruded body feature is created to beconsidered as insert, normally, this function is used to patch the holes on the face as well.:Extend the selected body face to the bottom face of core or cavity, so it could be taken asan insert body. It is normally used to convert a solid patch to insert body.Sample:Two small solid patches are converted to two insert bodies.Split from main insert:Select in sequence the bottom face of the mold core or cavity and a closed chain edges todefine the sub-insert body.Continuous edge tool is normally used to help user to pick up the chain edges, this way, a closedloop is ensured.39
:Using sketch to define the insert body. Select a sketch, click this ion, the insert body is cutfrom the core/cavity immediately.This is the most flexible way to define an insert body. User can use SolidWorks sketch tools tocreate the insert profile.:Same as SolidWorks core function. To use this function, select a sketch and click thisbutton, the SolidWorks “Core” page will pops out.Compare to the sketch way mentioned above, the core function is good at creating a blind insert.:Same as SolidWorks split function. The splitted bodies normally don’t need the pocketsand holders as the typical rectangular ones or circular ones.:Create a drafted insert body. Select the bottom face and some faces with draft to form theinsert body. An example is shown as the following picture.40
Page 1 and 2: 3D QuickTools LimitedConcept & Tuto
Page 3 and 4: 4.11 Face Search ..................
Page 5 and 6: 14.3 Holder........................
Page 7 and 8: Each mold design module is listed b
Page 9 and 10: Chapter 1.Set ProjectThis is not a
Page 11 and 12: 3.1 WorkpieceWorkpiece is used to d
Page 13 and 14: 3.2 Search Cavity/Core facesThis is
Page 15 and 16: 3.3 Extract parting linesOnce the c
Page 17 and 18: Note: The Shut-off surface feature
Page 19 and 20: Radiate surface:Select the referenc
Page 21 and 22: Please ensure the pre-selected core
Page 23 and 24: Chapter 4.QM-SolidPartingSolid Part
Page 25 and 26: Extend by distance: Extend the sele
Page 27 and 28: Revolved faces: Select revolved fac
Page 29 and 30: There are two ways to define the pa
Page 31 and 32: After the setting is completed, cli
Page 33 and 34: Usage 2:select one or more adjacent
Page 35 and 36: Searching sample with different opt
Page 37 and 38: Select a face or edge on body, clic
Page 39: 5.2 bodyThis functions works on par
Page 43 and 44: AdvancedClick the Advanced button o
Page 45 and 46: :Select the rectangular face and an
Page 47 and 48: :Rectangular insert holder.:Bottom
Page 49 and 50: Insert name and material can be spe
Page 51 and 52: :Double flange on the insert. Selec
Page 53 and 54: 6.2 ToolsList the existing runners
Page 55 and 56: Activate the Tools page, click, the
Page 57 and 58: :Select the orgin and a point on an
Page 59 and 60: :Select the orgin and a point on an
Page 61 and 62: :Select a sketch line or connected
Page 63 and 64: :Select a reference plane to be the
Page 65 and 66: 2. Side gate:Select a sketch point
Page 67 and 68: Chapter 7.Layout ManagerLayout Mana
Page 69 and 70: If nothing is pre-selected, 3DQuick
Page 71 and 72: Click Apply once the setting is don
Page 73 and 74: Duplicate:Duplicate the selected ca
Page 75 and 76: H1 (cavity): Define the thickness o
Page 77 and 78: Show bitmap: Show bitmap near the d
Page 79 and 80: Reverse hide:Show only the selected
Page 81 and 82: Add/Remove: Add or remove selected
Page 83 and 84: Chapter 9.Ejector WizardEjector Wiz
Page 85 and 86: Select point, edge or face to defin
Page 87 and 88: Decimal places:From 0 to 4, user ca
Page 89 and 90: Position ejector:Select the sketch
Page 91 and 92:
:Stepped ejector, :Ejector blade, :
Page 93 and 94:
Clearance height:The Clearance heig
Page 95 and 96:
:Select the planar face where the e
Page 97 and 98:
Clearance height:Select this will i
Page 99 and 100:
Chapter 10. Cooling WizardThe uses
Page 101 and 102:
:Pick up one face, a sketch line en
Page 103 and 104:
Methods available for creating the
Page 105 and 106:
Use Solidworks sketch utilities to
Page 107 and 108:
10.3 ParametersIt is for building t
Page 109 and 110:
Select a sketch point on the coolin
Page 111 and 112:
10.4 AccessorySome typical standard
Page 113 and 114:
After cooling channel is created, u
Page 115 and 116:
To add a screw, select a type, a pa
Page 117 and 118:
:mate reference. It could be the sp
Page 119 and 120:
Chapter 12.Slider WizardCustomer ca
Page 121 and 122:
: Slider body type 2Method: same as
Page 123 and 124:
: Slot type 3 for connection of sli
Page 125 and 126:
Method: select a face and an edge a
Page 127 and 128:
:Open direction, select planar face
Page 129 and 130:
13.2 BodyThere are some tools for c
Page 131 and 132:
:Extend lifter body to the selected
Page 133 and 134:
The following five icons are applic
Page 135 and 136:
After selecting two faces, click ea
Page 137 and 138:
: Guide plate. Select a inclined fa
Page 139 and 140:
Simulate: Lifter animation function
Page 141 and 142:
14.2 BodyThe functions on this page
Page 143 and 144:
Select four edges as the following
Page 145 and 146:
Selection:Select sketch on the part
Page 147 and 148:
:Prefix for the electrode bodyClick
Page 149 and 150:
Click OK, an electrode holder is cr
Page 151 and 152:
:Copy body, select a face on the ex
Page 153 and 154:
Angle/Z:Angle value between the nor
Page 155 and 156:
16.6 Create PocketCreate pockets fo
Page 157 and 158:
16.9 Set configurationIn a multiple
Page 159 and 160:
16.10 Save projectSave the entire a
show all

3DQuickMold Training Manual - 3D CAD/CAM Design Software

Create successful ePaper yourself

Delete template?

Save as template?