CUSTOM AVIONICS PANELS - SkyShop

LOBSTER MOUNTS - GPS MOUNTS
LOBSTER MOUNTS
The Shrimp Series of mounts provide an economical solution for
mounting mobile electronics. This basic system provides a minimal e -
tension, and utilizes a tri-wing finger knob for locking and positioning. Our
off-centered 1-1/4 inch ball-base patent pending provides adaptability
that cannot be matched. The Shrimp mount e tends as little as 2-1/2
inches from the mounting surface and can e tend to about 5 inches. The
Shrimp was designed to support devices up to 3 lbs, and is available
with bolt-on, MC/ATV, and Suction bases.
UNIVERSAL MC-ATV CLAMP - Base only For an additional
anchor point we offer this universal rail-clamping
base, designed to fit square or round tubing from 3/4 inch
to 1-1/2 inch diameter by adding a 1/4-20 3 bolt, this
base will fit up to 1-3/4 tube . This rugged base is made
from e truded aluminum, an aluminum ball, and includes
stainless steel hardware. eight - nit 0.5 lbs.
P/N 11-04709............................
UNIVERSAL CRADLE - The Cradle comes with four grip
fingers and one stop finger, which are capable of being
positioned in any of the eight slots on the body. Rubber
pads for the grip fingers and stainless steel hardware are
provided. In the short direction, the grip fingers are ad ustable
from 1-1/2 to 3-1/4 , and in the long direction, the
grip fingers ad ust from 4-1/2 to 5-1/2 . For longer devices,
the fingers on top could be left off, allowing the device to overhang
the cradle base. This product, like our other products is produced for use
in aviation and marine environments where being compass compatible
and corrosion resistant are important. P/N 11-04710............................
SHRIMP SERIES BOLT-ON WITH CAMERA TOP - A removable
1/4-20 camera stud, universal mounting ball-base and
mounting flange, lanyard loop accommodates the AMPS
bolt up pattern AMPS is a 1-1/2 by 1-3/16 screw hole pattern
used in many portable electronic products . Aluminum
alloy and reinforced composite parts with stainless steel
hardware. P/N 11-04711............................
SHRIMP SERIES MC/ATV CLAMP WITH CAMERA TOP
- Same as our Bolt-On model, while adding a universal
rail-clamping base, designed to fit square or round tubing
from 3/4 inch to 1-1/4 inch diameter by adding a 1/4-20
3 bolt, this base will fit up to 1-3/4 tube . This rugged
base is made from e truded aluminum, an aluminum ball,
and includes stainless steel hardware. P/N 11-04713............................
SHRIMP SERIES BOLT-ON + CRADLE - niversal
mounting ball-base and mounting flange, lanyard loop,
along with our cradle for hand-held devices. The Cradle
N-198 comes with four grip fingers and one stop finger,
which are capable of being positioned in any of the
eight slots on the body. Rubber pads for the grip fingers
and stainless steel hardware are provided. In the short direction, the grip
fingers are ad ustable from 1-1/2 to 3-1/4 , and in the long direction, the
grip fingers ad ust from 4-1/2 to 5-1/2 . For larger devices, the finger
may be left out at the top allowing the device to overhang the cradle
base. Like our other products, the S -259 is produced for use in aviation
and marine environments where being compass compatible and corrosion
resistant are important. P/N 11-04715............................
SHRIMP SERIES SUCTION + CRADLE - Our Suction Base attachment
ball is capable of being tilted for e tra versatility in positioning
your device. Cradle N-198 comes with four grip fingers and
one stop finger, capable of being positioned in any of the eight
slots on the body. Rubber pads for the grip fingers and stainless
steel hardware are provided. In the short direction, the grip fingers
are ad ustable from 1-1/2 to 3-1/4 , and in the long direction, the grip
fingers ad ust from 4-1/2 to 5-1/2 . For larger devices, the finger may be
left out at the top allowing the device to overhang the cradle base. This
mount, like our other products is produced for use in aviation and marine
environments where being compass compatible and corrosion resistant
are important. P/N 11-04716............................
SHRIMP SERIES MC/ATV + CRADLE - A universal railclamping
base, designed to fit square or round tubing
from 3/4 inch to 1-1/4 inch diameter. Made from e truded
aluminum, an aluminum ball, and includes stainless steel
hardware. Cradle comes with four grip fingers and one
stop finger, capable of being positioned in any of the eight slots on the
body. Rubber pads for the grip fingers and stainless steel hardware are
provided. In the short direction, the grip fingers are ad ustable from 1-1/2
to 3-1/4 , and in the long direction, the grip fingers ad ust from 4-1/2 to
5-1/2 . For larger devices, the finger may be left out at the top allowing
the device to overhang the cradle base..P/N 11-04717 ...........................
UN-327 SUCTION BASE - Suction Base Only, If you are
already using a Bolt-On or MC/ATV base, this allows you
to easily transfer your device to your car or any place with
a smooth surface. The Suction Base attachment ball is
capable of being titled for e tra versatility in positioning
your device. This base, like the other products is produced
for use in aviation and marine environments where being
compass compatible and corrosion resistant are import.
P/N 11-06616............................
SH-334 SHRIMP SUCTION MOUNT WITH CAMERA TOP -
Our Suction Base attachment ball is capable of being tilted for
e tra versatility in positioning your device. The Camera Top
N-310 has a removable 1/4-20 camera stud. It also features
a mounting surface with holes and slots, which accommodate
the AMPS standard 1.496 1.181 pattern for direct
attachment to numerous electronic devices. This base, like
our other products, is produced for use in aviation and marine
environments where being compass compatible and corrosion resistant
are important. P/N 11-06617............................
UN-303 ROLL BAR CLAMP - Base only For your ATV,
golf cart steering column or other applicable with 1-1/2 to
2-1/2 tubing. This rugged base is made from aluminum
e trusion, an aluminum ball, and zinc plated steel hardware.
Note that this is not compass friendly.
P/N 11-06618............................
UN-310 CAMERA TOP - Camera Mounting surface that
can also be used for mounting other devices. If you are
already using a niversal Cradle N-198 , this allows
you to easily use your mounting system for other purposes.
The holes and slots in the flange accommodate the
AMPS standard pattern as well as several size u-bolts.
This base, like our other products is produced for use in
aviation and marine environments where being compass-compatible and
corrosion resistant are important. P/N 11-06615............................
ROTATING MOUNT FOR GARMIN GPS
The rotating mount attaches to the Garmin yoke mount supplied with the
GPS units. The GPS then mounts on the product and allows the GPS
unit to be rotated so the passenger can view the unit if mounted on the
pilots side. If used on the co-pilots side, then the pilot can rotate the GPS
so he/she can view it as well. Note The rotating mount is used for the
Garmin GPS units 295,196,296,396
Rotating Mount for Garmin GPS LF............. P/N 11-04661.....................
Rotating Mount for Garmin GPS RT ............ P/N 11-04662.....................
ANGEROLE INSTRUMENT PANEL MOUNT
The photo illustrates the Model 241 040
fitted to a blank instrument panel. An
adaptor plate included with the mount
fits any standard 2-1/4 instrument panel
hole so, generally, it can be fitted without
any modifications to your airplane. If your
application needs it, we can supply this
mount with a 3-1/8 panel adaptor plate.
If you don t have an unused panel hole, a
viable alternative is to drill two holes and
simply bolt the mount directly to your panel.
The footprint area is only 2 0.5 so
there s probably going to be somewhere
you can make it fit. Naturally, you need
to be certain this is appropriate, sensible
and legal for your installation before drilling holes in your airplane.
P/N 11-07238........................................
537
CM
WP
ME
HA
AP
LG
EP
CS
IN
EL
AV
TO
PS
BV