Cat. 3 Custom Made Chain - Tsubaki Europe

ANSI DRIVE CHAIN FOR SPECIAL ENVIRONMENTSWhether your operation requires a sanitary environment, is exposed to corrosivechemicals, is heated to extreme temperatures, runs through a freezer, is exposed tothe outdoors or is affected by excessive moisture: our specially designed and testedchains will outlast your current chains and contribute to a cost effective application.Lambda Lube Free Chain(Carbon Steel base)ANSI X-LAMBDA Ultra Long LifeThe inclusion of a felt seal in the construction of the X-LAMBDAincreases the anti-wear performance to more than 5 times ofbasic LAMBDA Chain.ANSI LAMBDA KF SeriesDue to the special NSF-H1 certified lubrication impregnated bushes,TSUBAKI LAMBDA KF Series is usable in a wide temperaturerange (from -10°C to 230°C), and for food product applicationswhile at the same time being kind to the environment.Corrosion Resistant Chain(Titanium base/Stainless Steel base)ANSI TI Titanium ChainANSI TI Series chains are made completely of Titanium.Available in sizes RS35TI - RS40TI, TI Series brings the uniqueproperties of Titanium to roller chain applications, specificallyextreme corrosion resistance in a lightweight chain.TI chains are extremely lightweight (50% of the weight of carbonsteel) and are made completely of titanium, making it both nonmagneticand highly corrosion resistant.Working temperature range: -20°C to 400°CANSI PC Engineering Plastic Combination ChainThe pins and pin link plates of these chains are made of SUS304(spring clips SUS301). Engineering Plastic (white) is used for theinner link. This combination makes it a lube-free, low noise(5 dB lower than ANSI standard roller chain) and lightweightchain (50% lighter than ANSI standard roller chain). Working temperaturerange: -20°C to 80°CFor details see our catalogue 1 and 2.ANSI PC-SY Engineering Plasic Combination ChainThis chain combines Titanium pins and outer link plates withEngineering Plastic (off-white) inner links. It is suitable when thecorrosion resistance of Poly Steel chain (PC) is not sufficient. Witha working temperature range: –20°C to 80°C. The MaximumAllowable Load is 60% of that of Poly Steel chain (PC).For details on corrosion resistance, please check out the table inthe back of this catalogue as a basic guide.ANSI NS Stainless Steel ChainThis is a roller chain composed of SUS316 stainless steel (onlyRS25NS clips are SUS301). This chain is suitable when corrosionresistance greater than ANSI SS chain is required. There are nomagnetic parts besides the clip. ANSI NS chain can be used inhigh and low temperatures (-20°C to 400°C).ANSI SS Stainless Steel ChainAll basic components of this chain are made of Stainless SteelSUS304 (except the spring clips, which are made of SUS301).This chain can be used in special environments such as underwater,acidic and alkaline applications. It can also be used inhigh and low temperatures (-20°C to 400°C). SUS304 is onlymarginally magnetic, due to the cold-forging process.For details see our catalogue 1 and 2.ANSI AS Stainless Steel ChainThe pins and rollers of this roller chain are made of precipitationhardened,tempered stainless steel (SUS600). The link platesand the bushes are made of SUS304 stainless steel (spring clipsare SUS301). The Maximum Allowable Load is 1.5 times that ofANSI SS chain. Corrosion resistance is slightly lower thanstandard SS chain. This chain is suitable where corrosion andheat resistance is required in a heavy duty drive application andwhere a smaller ANSI SS chain is preferred. Magnetism existsdue to the use of precipitation-hardened SUS600. The workingtemperature range: -20°C to 400°CFor details see our catalogue 1.14 Innovation in Motion