ENGINEERING/TECHNICAL - Dodge-pt.com

Gearing Reference Guide
TORQUE-ARM II
TORQUE-ARM
MAXUM Concentric Reducer
TIGEAR-2
ENGINEERING/TECHNICAL
MAXUM Concentric Reducer
Table 24: Low Speed Overhung Loads
Approx.
Overhung Load Capacity
Unit
Low Speed MAXUM Reducer Size (multiply value shown by 1000) ♣
Red.
Shaft RPM 1 2 3 4 5 6 7 9 10 11 12
777.8
1.38 1.94 2.29 2.87 3.69 4.84 • • • • •
636.4 1.43 2.05 2.37 2.96 3.87 5.07 • • • • •
519.3 1.54 2.16 2.52 3.12 4.08 5.33 • • • • •
423.7 1.41 2.1 2.64 3.17 3.98 5.39 • • • • •
345.8 1.47 2.19 2.78 3.32 4.18 5.65 7.05 10.3 10.3 12.2 10.4
282.3 1.54 2.28 2.94 3.51 4.39 5.95 7.56 10.7 10.9 12.8 10.9
230.6 1.62 2.32 3.13 3.70 4.66 6.29 7.48 11.2 11.5 13.4 11.3
188.2 1.74 2.53 3.31 3.91 4.95 6.61 8.27 11.9 12.1 14.1 12.0
153.6 1.90 2.74 3.48 4.14 5.27 6.98 8.97 12.5 12.7 14.9 12.7
125.4 2.07 2.98 3.70 4.37 5.71 7.43 9.88 13.3 13.5 15.7 13.8
102.4 2.26 3.24 3.92 4.63 6.16 7.78 10.9 14.1 14.2 16.6 14.9
83.6 2.47 3.51 4.19 4.98 6.62 8.25 11.8 14.9 15.1 17.7 16.0
68.3 2.70 3.79 4.47 5.46 7.13 8.66 13.1 15.8 16.0 19.4 17.5
55.8
2.91 4.08 4.85 5.86 8.03 9.64 14.6 16.9 17.5 21.7 19.6
45.5 3.16 4.40 5.22 6.31 8.51 10.2 15.4 18.2 18.5 22.6 21.0
37.2 3.40 4.74 5.48 6.80 8.85 10.5 16.6 19.7 19.9 24.4 22.8
30.4 3.55 4.78 5.48 6.98 8.88 10.5 17.8 20.0 21.8 26.5 24.8
24.8 3.58 4.80 5.48 6.98 8.90 10.5 17.8 20.0 23.7 28.6 27.1
20.2 3.58 4.80 5.48 6.98 8.95 10.6 17.9 20.0 24.6 29.5 29.4
16.5 3.60 4.83 5.48 6.98 8.98 10.6 17.9 20.0 24.6 29.5 29.4
13.5 3.60 4.85 5.48 6.98 9.00 10.6 17.9 20.0 24.6 29.5 29.4
11.0 3.63 4.85 5.48 6.98 9.03 10.6 18.0 20.0 24.6 29.5 29.4
9.0 3.63 4.85 5.48 6.98 9.05 10.7 18.0 20.0 24.6 29.5 29.4
DOUBLE
TRIPLE
* Interpolate for intermediate values.
♣ Capacities are for pure radial loads.
If overhung loads are applied at the same time as thrust loads, consult DODGE Application Engineering.
• Consult DODGE.
Table 25: Actual Ratios
AGMA
Nominal
Ratio
Approx.
Low Speed
Shaft RPM
Unit
Red.
1 2 3 4
Actual Ratio of Reduction
MAXUM Reducer Size
5 6 7 9 10 11 12
2.25 777.8
2.253 2.259 2.263 2.225 2.263 2.273
2.75 636.4 2.801 2.800 2.760 2.679 2.750 2.770
3.37 519.3 3.406 3.373 3.364 3.320 3.338 3.392
4.13 423.7 4.091 4.108 4.167 4.125 4.114 4.133
5.06 345.8 5.087 5.091 5.081 4.966 5.000 5.037 5.065 5.103 4.958 5.104 5.089
6.20 282.3 6.184 6.133 6.194 6.154 6.069 6.167 6.115 6.154 6.109 6.134 6.220
7.59 230.6 7.639 7.484 7.813 7.586 7.520 7.680 7.527 7.478 7.589 7.552 7.464
9.30 188.2 9.282 9.333 9.524 9.280 9.273 9.273 9.217 9.200 9.385 9.077 9.325
11.39 153.6 11.28 11.30 11.33 11.45 11.37 11.37 11.21 11.20 11.33 11.28 11.31
13.95 125.4 13.79 14.00 14.09 13.89 14.00 14.25 13.91 13.88 13.93 13.89 13.98
17.09 102.4 16.87 17.18 17.13 17.00 17.14 16.86 17.47 17.14 16.73 16.90 16.90
20.93 83.6 20.83 21.14 21.11 20.57 20.67 20.67 21.06 21.00 20.92 20.83 20.60
25.63 68.3 25.64 25.67 25.32 26.18 25.20 24.67 25.68 25.60 25.89 25.32 25.59
31.39 55.8
30.90 30.96 31.28 31.50 31.38 32.00 30.50 30.68 31.61 31.29 31.21
38.44 45.5 37.77 38.35 38.88 38.21 38.64 40.11 37.83 38.03 38.86 38.51 38.60
47.08 37.2 46.20 47.05 47.28 46.75 47.31 47.45 47.53 46.96 46.68 46.85 46.63
57.67 30.4 57.05 57.91 58.27 56.57 57.04 58.17 57.29 57.52 58.36 57.77 56.85
70.62 24.8 70.22 70.30 69.88 72.00 69.55 69.43 69.86 70.12 72.21 70.21 70.63
86.50 20.2 85.73 85.91 85.52 86.86 86.81 86.21 86.27 86.94 85.07 86.60 86.36
105.9 16.5 104.8 106.4 106.3 105.4 106.9 108.1 104 106.5 106.4 106.8 106.8
129.7 13.5 128.2 130.5 129.3 128.9 130.9 127.8 126.8 129.8 131.6 129.8 129
158.9 11.0 158.3 160.7 159.3 156 157.8 156.7 158.9 157.5 159.8 159.1 157.3
194.6 9.0 194.8 195.1 191.1 198.5 192.4 187.1 193.8 192 197.7 193.4 195.4
† Based on 1750 high speed shaft RPM.
Sizes 1-3 discounted remaining sotck may be avaialble.
FEATURES/BENEFITS
PAGE G3-3
DOUBLE
TRIPLE
NOMENCLATURE
PAGE G3-6
G3-74
EASY SELECTION
PAGE G3-7
SELECTION/DIMENSIONS
PAGE G3-23