Norcold Repair Guide Models 442, 443, 452, 453, 462, 463, 482 ...

More documents

Recommendations

Info

A008Component Location andIdentification (Single Door<strong>Models</strong>)A. Illuminated Ignition SwitchB. Flame On Indicator LampC. Thermostat Control KnobD. Combination Control Knob1. Gas On/Electric Interlock2. Push-In Safety ValveE. AC/DC Mode Selector Switch(3-Way models only)F. Serial Identification PlateFA B C D EFigure 3.2Controls Location, Single Door ModelGHComponent Location andIdentification (Two Door<strong>Models</strong>)A. Illuminated Ignition SwitchB. Flame On Indicator LampC. Thermostat Control KnobD. Combination Control Knob1. Gas On/Electric Interlock2. Push-in Safety ValveE. AC/DC Mode Selector Switch(3-Way models only)F. Serial Identification PlateG. Three Position Switch (Seepage 3-6)1. NORMAL2. STORAGE3. HIGH HUMIDITYH. Interior Light SwitchFA B C D EFigure 3.3Controls Location, Two Door Model3-4
B101Lighting Instructions: GasOperationLighting and Operating Instructions1. Make certain that 12 Volts DCis available to the refrigerator.2. Turn on gas supply at the tank.3. Set thermostat control to themaximum cold setting.4. Set ignitor switch to "ON" position.The light located on theswitch will illuminate if 12 voltsDC is present.5. Push and turn the "ELEC-OFF-GAS" control counter-clockwiseso that knob indicator points to"GAS". Push the control knoband hold it until the flame indicatorilluminates (continuousglow). Continue to hold approximately5 seconds, then release.The flame indicator will remainon. If not, repeat this step.Note:The flame should ignite within 10seconds. On initial refrigerator startup,it may take longer than 10 secondsto allow air to be purged fromthe gas line, as indicated by theflame indicator failing to illuminate.WARNINGDO NOT HOLD GAS CONTROLVALVE IN MORE THAN 30 SEC-ONDS. IF FLAME IS NOT INDI-CATED WITHIN THIS TIME, TURNGAS TO "OFF", WAIT 2 MINUTESAND RETRY. FAILURE TO DO SOCAN CAUSE GAS TO BUILD UP INBURNER AREA AND RESULT IN ANEXPLOSION WHICH CAN CAUSEPERSONAL INJURY OR DEATH.6. Move thermostat control to desiredsetting.7. The ignitor switch should beleft in the "ON" position duringgas operation. If the switch isturned off, the refrigerator willcycle normally. However, incase of flame blowout, the relighterdoes not function.Figure 3.4 2-Way Controls (Upper), 3-Way Controls (Lower)Start-Up Instructions : AC Electric Operation1. Make certain that 120 Volts AC is available to the refrigerator.2. Set the thermostat control to desired setting.3. Set "AC-DC" switch to "AC" position (3-Way models only).4. Set ignitor switch to "OFF" position.5. Push and turn the "ELEC-OFF-GAS" Control clockwise so that knob indicatorpoints to "ELEC". Upon release, note that the knob moves towardyou, indicating that the control is locked into electric position.Start-Up Instructions: DC Electric Operation (3-Way only)1. Make certain that 12 Volts DC is available to the refrigerator.2. Set thermostat control to desired setting.3. Set "AC-ELECTRIC STANDBY-DC" switch to "DC" position.4. Set ignitor switch to "OFF" position.5. Push and turn the "ELEC-OFF-GAS" control clockwise so that knob indicatorpoints to "ELEC". Upon release, note that the knob moves towardyou, indicating that the control is locked into electric operation.Operation Note:Use the "ELEC-OFF-GAS" control to shut off all cooling operation (bothGas and Electric). The "GAS IGNITOR" switch must be shut off independentlyto prevent unnecessary sparking.On 3-Way models, use the "ELECTRIC STANDBY" position of the "AC-ELEC-TRIC STANDBY-DC" switch to temporarily shut off AC or DC operation.Operation Shut-Down: All Modes1. Set ignitor switch to "OFF" position.2. Push and turn "ELEC-OFF-GAS" control to "OFF".3-5
Page 1 and 2: B101Norcold Repair GuideModels 442,
Page 3: B101Information About Electrical Co
Page 7 and 8: B101Parts FunctionCombination Contr
Page 9 and 10: B101BurnerApplies the correct amoun
Page 11 and 12: B1014. To check for loose wire conn
Page 13 and 14: B101Flame will not stay lit(Lights
Page 15 and 16: B101Refrigerator Overfreezing1. Wit
Page 17 and 18: B1018. Check for 120 Volts at eacht
Page 19 and 20: B1015. If preceding checks did not
Page 21 and 22: B1013-21
Page 23 and 24: B1013-23
Page 25 and 26: B101This Page Contains Information
Page 27 and 28: - 27 -исте захтеве о о
Page 29 and 30: This Page Contains Wiring Diagrams
Page 31: !" ! #$%& '( & '

Norcold Repair Guide Models 442, 443, 452, 453, 462, 463, 482 ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?