User manual METTLER TOLEDO Weighing terminal IND425

More documents

Recommendations

Info

Settings in the menuIND4253.6.2 COM1/COM2 -> PRINTER – settings for protocol printoutThis menu item only appears if the mode "Print" or "A.Print" is selected.tEmPLatSelecting protocol printoutStdArd • Standard printouttEmPLt1 • Printout in accordance with Template 1tEmPLt2 • Printout in accordance with Template 2ASCi.FmtTSelecting formats for the protocol printoutLINE.Fmt • Line format: MULtI (multi-line) or SINGLE (single-line)LENGtH • Line length: 0 ... 100 characters, appears only with line format MULtISEPArAt • Separator: , ; . / \ _ and space; appears only with line format SINGLEAdd LF • Line feed: 0 ... 9bAUdPAritYH.SHAKE3.6.3 COM1/COM2 -> PARAMET – communication parameterSelecting baud rate: 300, 600, 1200, 2400, 4800, 9600, 19200, 38400 baudSelecting parity: 7 none, 8 none, 7 odd, 8 odd, 7 even, 8 evenSelecting Handshake: NO, XONXOFF, nEt422, nEt485 (network operationas per RS485 standard via the optional RS422/RS485 interface, only for COM1)NET.Addr Assigning network address: 0 ... 31, only for NET 485ChECSuMActivating checksum byte (appears only in TOLEDO Continuous mode)VccSwitching 5V voltage, e.g. for a bar code reader, on / off3.6.4 COM1/COM2 -> RESET COM1/RESET COM2 – resetting serial interface to factorysettingsSUrE?Confirmation inquiry• Reset interface settings to factory settings with• Do not reset the interface settings with T3.6.5 OPTION – configuring optionsIf no option is installed or is not yet configured, N.A. appears in the display.EtH.NEtConfiguration of the Ethernet interfaceIP.AddrS • Enter IP addressSUBNEt • Enter Subnet addressGAtEWAY • Enter Gateway addressUSbConfiguration of the USB interfaceUSb TEST • Test of the USB interface. After the test has been passed, rEAdY appears in thedisplay.22User manual 22011481A 03/05
IND425Settings in the menudiGitALConfiguration of the digital inputs/outputsIN 1 ... 4 Configuring inputs 1 ... 4OFF • Input not assignedZErO • KeytArE • KeyPriNt • KeyCLEAr • KeyUNIt • KeyOUT 1 ... 4 • Configuring outputs 1 ... 4OFF • Output not assignedStAbLE • Stable weight valuebEL.MIN • Minimum weight not reachedAbV.MIN • Minimum weight reached or exceededUNdErLd • Insufficient loadOVErLd • OverloadStAr • Changed/calculated valueTC3.6.6 DEF.PRN – configuring templatestEMPLt1/tEMPLt2 Selecting Template 1 or Template 2LINE 1 ... 20 Select lineNOt.USEd • Line not usedHEAdEr • Line as header. The contents of the header must be defined via an interface command,see Section 4.1.GROSS • Gross weighttArE • Tare weightnEt • Net weightStARLN • Line with ***CrLF • Line feed (blank line)F FEEd • Page feedUser manual 22011481A 03/0523
Page 1 and 2: User manualMETTLER TOLEDOWeighing t
Page 3 and 4: IND425Table of contentsTable of con
Page 5 and 6: IND425IntroductionCAUTION!On no acc
Page 7 and 8: IND425Introduction1.2.2 Display1 Ac
Page 9 and 10: IND425Introduction1.3 Putting into
Page 11 and 12: IND425Operation2.4 Weighing with ta
Page 13 and 14: IND425Operation2.7 CleaningCAUTION!
Page 15 and 16: IND425Settings in the menu3.1.2 Sel
Page 17 and 18: IND425Settings in the menuLevel 1 L
Page 19 and 20: IND425Settings in the menu3.3.5 RES
Page 21: IND425Settings in the menuSUPErVIEN
Page 25 and 26: IND425Interface description4 Interf
Page 27 and 28: IND425Interface description4.1.2 Re
Page 29 and 30: IND425Interface descriptionStatus w
Page 31 and 32: IND425Event and error messagesError
Page 33 and 34: IND425Technical data and accessorie
Page 35 and 36: IND425Appendix7 Appendix7.1 Safety
Page 37 and 38: IND425Appendix7.2.2 GEO VALUES 6000
Page 39 and 40: IND425Index8 IndexAAccessories ....

User manual METTLER TOLEDO Weighing terminal IND425

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?