ZA180(I) Series Runway Centreline & TDZ - IHR-Aviation
ZA180(I) Series Runway Centreline & TDZ - IHR-Aviation
ZA180(I) Series Runway Centreline & TDZ - IHR-Aviation
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>IHR</strong> GmbH Hofmeister + Rumpfwww.ihr-aviation.net<strong>ZA180</strong>(I) <strong>Series</strong><strong>Runway</strong> <strong>Centreline</strong> & <strong>TDZ</strong>runway high intensity inset lightfeatures• Lightweight and robust aluminium alloy construction whichalso gives good corrosion resistance• Dichroic coated lenses for coloured light options• Full range of FAA and PSA adaptors available• Anti-rotation pin locations• Left and right toe-in option for <strong>TDZ</strong> version• Long life, low energy lamps (1500 hrs/45W or 49W at fullbrilliancy) - 1 or 2 off per fitting• Pre-focused optics simplify maintenance procedures• Light channel within 5mm from Grade• Two point fixing into mounting adaptor/seating pot for fasterinstallation and removal of light cartridge• Low profile (12mm) to reduce possibility of damage to aircraftand vehicle tyres• Twin-lead, bi-directional (switchable) versions available• Prisms accurately located and secured in the body castingwithout the need for sealing compound to facilitate removaland replacement• Optional lamp by-pass devices can be fitted if required• Generic with ZA280 and ZA292 IEC fittings• Clear anodised or powder coat paint finish in golden yellow. Allfasteners are stainless steel• IMM available on requestcompliance with standardsapplication<strong>Runway</strong> centreline or touchdown zone fitting for use in category I, II &III all weather operation airfield lighting systems.options• ZM203 (I) 8” seating pot• ZM109 8” seating pot (wet)• ZM181 8” seating pot (dry)• BS 12” adaptor flange• BS 15.5” adaptor flange• FAA 12” axial adaptor flange• ZS023 Sighting device• Extractor tool• ZM203 (I) installation jigelectrical supplySuitable for use in 6.6A airfield lighting circuits, normally supplied fromone 100W/150W or two 45W/65W series circuit isolating transformers.packaging dataNet weight 5kgGross weight 6kgCarton size 220mm(w) x 220mm(d) x 126mm(h)• FAAIn compliance with FAA L-850A & B, specificationsAC 150/5345-46C• ICAO In compliance with ICAO Annex 14, figs 2.5, 2.6,2.7 & 2.8• NATO In compliance with STANAG 3316• CAA CAP168, figs 6A/5, 6A/6 & 6A/7• BS3224 Part 5, inset fittings
<strong>IHR</strong> GmbH Hofmeister + Rumpfcomponentswww.ihr-aviation.net1 Body casting (anodised or golden yellow) Not Saleable2 Clear prism (1 or 2) SLC16069or red dichroic prismSLC191413 Blank for prism aperture SLC400924 Prism gasket (2) SLC330585 Prism clamp gasket SLC330696 Prism retaining clamp (2) SLC320377 Lampholder (1 or 2) SLC320408 Lamp retaining spring (1 or 2) SLC320399 Cold reflector lamp - 45/49W 6.6A (1 or 2) SLC0806510 Lamp gasket SLC3308311 Lamp by-pass disc assembly (1 or 2) DRG2884812 45W by-pass disc (1 or 2) SLC2113413 Seating pot ‘O’ ring seal SLC3309414 Gasket, body to base SLC3309515 Lampholder support block SLC2129616 Cable gland assembly (1 or 2) SLC21114/5/617 ‘B’ type plug lead (1 or 2) SLC13001typical installation methods• In 8” dia seating potatg airports type ZM203(I). Adaptor rings enable the fitting to bemounted into new or existing standard PSA 12” and 15.5” diaseating rings.• In FAA 12” dia L-868 baseInstallation on to FAA L-868 seating base can be achieved by usingan 8 -12” adaptor ring.ZA181(I) installed in ZM203(I) seating pot (dry)ZA181(I) installed on FAA L-868 base1.2.ZA181 (I) fitting (F29282)ZM203 (I) seating pot (F29276)3.4.Secondary leadGroutZA181(I) installed in ZM203(I) seating pot1.2.3.4.5.ZA181 (I) fitting (F29282)Mounting adaptor - axial *H29249)FAA L-868 base (one piece)Outer earth terminalInner earth terminal6.7.8.9.Isolating transformerSecondary connectionPrimary connectionGrommet
<strong>IHR</strong> GmbH Hofmeister + Rumpfwww.ihr-aviation.netphotometric performance<strong>Runway</strong> <strong>Centreline</strong> (15 metres) CAT III:Main Ellipse Intensity Measurements (Candelas)Average 6494Min. Average 5000Max (B) 9262Min (A) 3241Nominal Lamp DetailsPower45.0 WattsCurrent6.6 AmpsTypeCold Relfector LampICAOCAP168Annex 14 FIG 6A.7FIG 2.7Other photometric information available on request.colours pLUG LEAD bypass LAMP mounting adaptorsZM184(I)ZM181(I)WRNWhiteRedBlank12‘B’ Type lead, single‘B’ Type lead, twinYNNot FittedFitted121 Lamp2 Lamp2BS
<strong>IHR</strong> GmbH Hofmeister + Rumpfwww.ihr-aviation.netatg airports ltdAutomation House, Lowton Business Park, Newton Road, Lowton St. Mary’s, Warrington Wa3 2ap UKt +44 (0) 1942 68 5555 f +44 (0) 1942 68 5518 e products@atgairports.com w www.atgairports.com
<strong>IHR</strong> GmbH Hofmeister + Rumpfwww.ihr-aviation.netZA181 <strong>Runway</strong> <strong>Centreline</strong> & <strong>TDZ</strong>features• Lightweight, corrosion resistant and robust aluminium alloy• Dichroic coated lenses for coloured light options• Full range of FAA and PSA adaptors• Long life, low energy lamps (1500 hrs/49W at full brilliancy) - 1or 2 off per fitting• Pre-focused optics simplify maintenance procedures• Light channel within 5mm from Grade• Two point fixing into mounting adaptor/seating pot for fasterinstallation and removal of light cartridge• Low profile (12mm) to reduce possibility of damage to aircraftand vehicle tyres• Twin-lead, bi-directional (switchable) versions available• Prisms accurately located and secured in the body castingwithout the need for sealing compound• Optional lamp by-pass devices• Powder coat paint finish in golden yellow or NATO green. Allfasteners are stainless steel• IMM available on requestcompliance with standards• FAAIn compliance with FAA L-850A & B, specificationsAC 150/5345-46C• ICAO In compliance with ICAO Annex 14, figs 2.5, 2.6& 2.7• NATO In compliance with STANAG 3316• CAA CAP168, figs 6A/5, 6A/6 & 6A/7• BS3224 Part 5, inset fittingsapplication<strong>Runway</strong> centreline or touchdown zone fitting for use in category I, II &III all weather operation airfield lighting systems.options• ZM181 8” seating pot (wet)• ZM181 8” seating pot (dry)• BS 12” adaptor flange• ZS023 sighting device• Extractor tool• ZM181 installation jigelectrical supplySuitable for use in 6.6A airfield lighting circuits, normally suppliedfrom one 100W/150W or two 45W/65W series circuit isolatingtransformers.packaging dataNet weightGross weightCarton size5kg6kg220mm(w) x 220mm(d) x 126mm(h)
<strong>IHR</strong> GmbH Hofmeister + Rumpfcomponentswww.ihr-aviation.net1 Body casting anodised grey or golden yellow Not saleable2 Clear prism (1 or 2) SLC16069or red dichroic prismSLC191413 Blank for prism aperture SLC400924 Prism gasket (2) SLC330585 Prism retaining clamp (2) SLC320376 Lampholder (1 or 2) SLC320407 Lamp retaining spring (1 or 2) SLC320398 Cold reflector lamp - 45/49W 6.6A (1 or 2) SLC080659 Lamp by-pass disc assembly (1 or 2) DRG2884810 45W by-pass disc (1 or 2) SLC2113411 ’B’ type plug lead (1 or 2) SLC1300112 Base casting Not saleable(single lead) or base casting (twin lead)13 Cable gland assembly (1 or 2) SLC21114/5/614 ’O’ ring seal SLC3305915 Lamp gasket SLC3306416 Prism clamp gasket SLC3306917 Lamp holder support SLC21296typical installation methods• In 8” dia seating pot atg airports Type ZM181• In FAA 12” dia L-868 baseAdaptor rings (3BS or 4BS) enable the fitting to be mounted into Installation on to FAA L-868 seating base can be achieved bynew or existing standard PSA 12” and 15.5” dia seating ringsusing an 8 -12” adaptor ring (3FA, 3FR or 3FL).ZA181 installed in ZM181 seating pot (dry)ZA181 Installed on FAA L-868 BaseWet seating pot arrangements information available on request1.2.3.ZA181 fittingZM181 seating potSecondary lead4.5.GroutSlotsealGeneral arrangement1.2.3.4.5.6.ZA181 Fitting (F28828)FAA L-868 Base (one piece)Outer earth terminal (optional)Inner earth terminal (optional)Isolating transformerSecondary connection7. Primary connection8. Grommet9. Anchor ring10. ‘O’ Ring11. Dam ring
<strong>IHR</strong> GmbH Hofmeister + Rumpfwww.ihr-aviation.netphotometric performance<strong>Runway</strong> <strong>Centreline</strong> (15 metres) CAT IIIMain Ellipse Intensity Measurements (Candelas)Average 6494Min. Average 5000Max (B) 9262Min (A) 3241Nominal Lamp DetailsPower45.0 WattsCurrent6.6 AmpsTypeCold Relfector LampICAOCAP168Annex 14 FIG 6A.7FIG 2.7Other photometric information available on request.colours pLUG LEAD bypass LAMP finish mounting adaptorsZM181 W WhiteRRedNBlank12‘B’ Type lead, single‘B’ Type lead, twinYNNot FittedFitted121 Lamp2 LampyGGolden YellowNato Green2BS
<strong>IHR</strong> GmbH Hofmeister + Rumpfwww.ihr-aviation.netatg airports ltdAutomation House, Lowton Business Park, Newton Road, Lowton St. Mary’s, Warrington Wa3 2ap UKt +44 (0) 1942 68 5555 f +44 (0) 1942 68 5518 e products@atgairports.com w www.atgairports.com
<strong>IHR</strong> GmbH Hofmeister + Rumpfwww.ihr-aviation.netZA182 <strong>Runway</strong> Endhigh intensity uni-directional inset lightfeatures• Lightweight and robust due to its aluminium alloy constructionwhich also gives good corrosion resistance.• Red dichroically coated lens.• Full range of FAA and PSA adaptors available.• Long life, low energy lamps (1500 hrs/105W 6.6A at fullbrilliancy) - 1 off per fitting.• Pre-focused optics simplify maintenance procedures.• Light channel within 5mm from Grade.• Two point fixing into mounting adaptor/seating pot for fasterinstallation and removal of light fitting.• Low profile (12mm) to reduce possibility of damage to aircraftand vehicle tyres.• Prism accurately located and secured in the body castingwithout the need for sealing compound to facilitate removaland replacement• Powder coat paint finish in golden yellow or anodisedaluminium• All fasteners are stainless steel• IMM available on requestoptions• ZM181 8” seating pot (wet)• ZM181 8” seating pot (dry)• BS 12” adaptor flange• BS 15.5” adaptor flange• FAA 12” axial adaptor flange• ZS023 sighting device• Extractor tool• ZM181 installation jigelectrical supplySuitable for use in 6.6A airfield lighting circuits, normally supplied fromone 100W isolating transformer.packaging dataNet weight 5kgGross weight 6kgCarton size 220mm(w) x 220mm(d) x 126mm(h)compliance with standards• FAA AC 150/5345-46C/L-850D• ICAO Annex 14 3rd Edition, fig 2.8• NATO STANAG 3316• CAA CAP168, fig 6A/8 BS3224: Part 5, inset fittingsapplication<strong>Runway</strong> end fitting for use in category I, II & III all weather operationairfield lighting systems.
components<strong>IHR</strong> GmbH Hofmeister + Rumpfwww.ihr-aviation.net1 Body casting golden yellow SLC160692 Red prism SLC191413 Blank for prism aperture SLC400924 Prism gasket (2) SLC330755 Prism retaining clamp (2) SLC320376 Lampholder SLC320407 Lamp retaining spring SLC320398 Cold reflector lamp - 105W 6.6A SLC080759 Lamp by-pass disc assembly optional SLC2113510 100W by-pass disc optional SLC2113511 ‘B’ type plug lead SLC1302612 Base casting single lead Not saleable13 Sealing gasket SLC3307014 Lamp gasket SLC3308315 Prism clamp gasket SLC3306916 Lampholder support block SLC21296typical installation methods• In 8” dia seating potatg airports type ZM181 Adaptor rings (3BS or 4BS) enable thefitting to be mounted into new or existing standard PSA 12” and15.5” dia seating rings.• In FAA 12” dia L-868 baseInstallation on to FAA L-868 seating base can be achieved by usingan 8 -12” adaptor ring (3FA, 3FR or 3FL).ZA182 installed in ZM181 seating pot (dry)ZA182 installed on FAA L-868 base1.2.3.ZA182 fittingZM181 seating potSecondary lead4.5.GroutSlotsealGeneral Arrangement1.2.3.4.5.ZA182 fittingMounting adaptor - axialFAA L-868 base (one piece)Outer earth terminal (optional)Inner earth terminal (optional)6.7.8.9.Isolating transformerSecondary connectionPrimary connectionGrommet
<strong>IHR</strong> GmbH Hofmeister + Rumpfwww.ihr-aviation.netatg airports ltdAutomation House, Lowton Business Park, Newton Road, Lowton St. Mary’s, Warrington Wa3 2ap UKt +44 (0) 1942 68 5555 f +44 (0) 1942 68 5518 e products@atgairports.com w www.atgairports.com
<strong>IHR</strong> GmbH Hofmeister + Rumpfwww.ihr-aviation.netZA183 <strong>Runway</strong> Edgehigh intensity bi-directional inset lightfeatures• Lightweight and robust due to its aluminium alloy constructionwhich also gives good corrosion resistance• Designed to be mounted in 12” or 15.5” adaptor flange• Full range of FAA and PSA adaptors available• Long life, low energy lamps (1500 hrs/105W 6.6A at fullbrilliancy), 2 off per fitting• Pre-focused optics simplify maintenance procedures• Light channel within 5mm from Grade• Two point fixing into mounting adaptor for faster installationand removal of light fitting• Low profile (12mm) to reduce possibility of damage to aircraftand vehicle tyres• Prisms accurately located and secured in the body castingwithout the need for sealing compound to facilitate removaland replacement• Powder coat paint finish in golden yellow or anodisedaluminium. All fasteners are stainless steel• IMM available on requestcompliance with standards• FAA• ICAOIn compliance with FAA L-850C, specificationsAC 150/5345-46CIn compliance with ICAO Annex 14 3rd Edition,figs 2.9 & 2.10• NATO In compliance with STANAG 3316• CAA CAP168, figs 6A/9 & 6A/10• BS3224 Part 5, inset fittingsapplication<strong>Runway</strong> edge fitting for use in category I, II & III all weather operationairfield lighting systems.options• ZM110 12” seating pot• BS 12” adaptor flange• BS 15.5” adaptor flange• ZM480 12” seating pot• FAA 12” axial adaptor flange (dry)• FAA 12” axial adaptor flange (wet)• ZS023 sighting device• Extractor tool• ZM480 installation jigelectrical supplySuitable for use in 6.6A airfield lighting circuits, normally supplied fromeither one 200W or two 100W isolating transformers.packing dataNet weight 5kgGross weight 6kgCarton size 220mm(w) x 220mm(d) x 126mm(h)
<strong>IHR</strong> GmbH Hofmeister + Rumpfcomponentswww.ihr-aviation.net1 Body casting golden yellow or anodised aluminium Not saleable2 Clear prism (1 or 2) or SLC16069Red prism orSLC19141Yellow prism orSLC19153Green prismSLC191543 Blank for prism aperture SLC400924 Prism gasket (2) SLC330755 Prism retaining clamp (2) SLC320376 Lampholder (2) SLC320407 Lamp retaining spring (2) SLC320398 Cold reflector lamp - 105W 6.6A (2) SLC080759 Lamp by-pass disc assembly (1 or 2) optional DRG28848C10 100W by-pass disc (1 or 2) optional SLC2113511 ‘B’ type plug lead (1 or 2) SLC1302612 Base casting single lead Not saleableor twin leadNot saleable13 Cable gland assembly (1 or 2) SLC21282/3/414 Sealing gasket SLC3307015 Lamp gasket (2) SLC3308316 Prism clamp gasket (2) SLC3306917 Lampholder support block (2) SLC21296typical installation methods• In 12” dia seating pot atg airports type ZM110• In FAA 12” dia L-868 baseAdaptor rings (3BS or 4BS) enable the fitting to be mounted into Installation on to FAA L- 868 seating base can be achieved bynew or existing standard PSA 12” and 15.5” dia seating rings.using an 8 -12” adaptor ring (3FA, 3FR or 3FL).ZA480 Installed in ZM480 Seating Pot (dry version)ZA183 installed on FAA L-868 base1.2.3.ZA480 FittingZM480 Seating PotSecondary Connection4.5.6.Grout‘O’ RingCable GlandNoteZM480 Wet seating pot arrangement information available on request.General arrangement
<strong>IHR</strong> GmbH Hofmeister + Rumpfwww.ihr-aviation.netphotometric performance<strong>Runway</strong> EdgeWhiteZA183Main Ellipse Intensity Measurements (Candelas)Average 10409Min. Average 10000Max (B) 12851Min (A) 6560Nominal Lamp DetailsPower105.0 WattsCurrent6.6 AmpsICAOCAP168ANNEX Fig 6A/10Fig 2.10colours pLUG LEAD bypass LAMP finish mounting adaptorsZM183 W WhiteRRedNBlankyYellow12‘B’ Type lead, single‘B’ Type lead, twinYNNot FittedFitted121 Lamp2 LampycGolden YellowAnodised aluminium3BS 305mm dia (12”)PSA flange4BS 394mm dia (15.5”)PSA flange3fa 305mm dia (12”)FAA axial3fr 305mm dia (12”)FAA right handtoe-in (4°)3fl 305mm dia (12”)FAA left handtoe-in (4°)
<strong>IHR</strong> GmbH Hofmeister + Rumpfwww.ihr-aviation.netatg airports ltdAutomation House, Lowton Business Park, Newton Road, Lowton St. Mary’s, Warrington Wa3 2ap UKt +44 (0) 1942 68 5555 f +44 (0) 1942 68 5518 e products@atgairports.com w www.atgairports.com
<strong>IHR</strong> GmbH Hofmeister + Rumpfwww.ihr-aviation.netcomponents1 Marker cone (1-off) 292152 Rim (1-off) SLC292143 Glass dome ”O” ring (1-off) SLC330914 Glass dome (1-off) SLC160565 Filter glass various colours(1 or 2-off) See optional extras6 Filter clip (4 off) 292197 Lens holder (2-off) 292108 Lens (2-off) 279239 Top casting (1-off) 2921110 J1/80 Pk30d 100W SLC08057or J1/83 Pk30d 150WSLC08088or J1/84 Pk30d 200WSLC0808911 Lamp retaining spring (1-off) 2921612 Base casting “O” ring (1-off) SLC3309113 Lock spring (1-off) 2921714 Base casting (1-off) Not Saleable15 Short lead for 1”O/D stem16 B type lead for 1“ I/D and M32 stem SLC1300117 M20 elkay gland set and seal (1-off)18 1“ O/D stem 2922319 1“ I/D stem 2922220 M32 stem 2922121 Clamp (1-off) 2921322 M32 hexagonal nut (2-off)23 32 dia washer (2-off)24 Top Terminal Block Assy25 Base Terminal Block Assytypical installation methods• On a 204mm (8”) dia. ground mounting plate• On a FAA L867 type base can• On a ground mounting spike• On a FAA type frangible coupling• Other installation methods available on requestZA163 installed on 24mm (8”) ground mounting plateZA163 installed on a FAA L867 base canNoteThe ground mounting plate is designed to be held down by means of three 10mm(3/8”) rag bolts grouted into the concrete block on 178mm PCD1.2.3.4.ZA163 25mm O/D SpigotFAA Type L867 BaseplateFrangible CouplingFAA Type L867 Base5.6.7.Isolating transformerGasketSupport Plate
<strong>IHR</strong> GmbH Hofmeister + Rumpfwww.ihr-aviation.netZA163 installed on a FAA Type frangible couplingZA163 general arrangementAlternative support arrangements for ‘A’ or ‘B’ type socket leads mounted in a wells coupling1.2.3.ZA163 25mm O/D SpigotFrangible couplingWells coupling4.5.50mm dia. pipe (plastic or metal)Concrete blockZA163 installed on a short approach pole up to 2.2m longAlternative support arrangements for ‘A’ or ‘B’ type socket leads mounted in a wells coupling1.2.3.4.ZA163 M32 SpigotTop CouplingAluminum Tube 50.8O/D 10SWGFrangible coupling5.6.7.Wells Coupling50mm dia. pipeConcrete block
<strong>IHR</strong> GmbH Hofmeister + Rumpfphotometric performancewww.ihr-aviation.net<strong>Runway</strong> EdgeWhiteZA163Main Ellipse Intensity Measurements (Candelas)Average 12639Min. Average 10000Max (B) 17250Min (A) 6927Nominal Lamp DetailsPower150 WattsCurrent6.6 AmpsType J1/83CAP168 6A.9ICAO 2-9<strong>Runway</strong> EdgeWhiteZA163Main Ellipse Intensity Measurements (Candelas)Average 10916Min. Average 10000Max (B) 15058Min (A) 5785Nominal Lamp DetailsPower200 WattsCurrent6.6 AmpsType J1/84CAP168 6A.10ICAO 2-10Other photometric information available on request.colours LAMP mounting stemZA163 w WhiteyYellowrRedgGreenbBlue100150200M3225mm O/D25mm I/Datg airports ltd Automation House, Lowton Business Park, Newton Road, Lowton St. Mary’s, Warrington Wa3 2ap UKt +44 (0) 1942 68 5555 f +44 (0) 1942 68 5518 e products@atgairports.com w www.atgairports.com
<strong>IHR</strong> GmbH Hofmeister + Rumpfwww.ihr-aviation.netZA460 <strong>Runway</strong> Edge Lightfeatures• Choice of three mounting stems available:- M32 threaded frangible spigot- 25mm I/D socket with side cable entry- 25mm O/D spigot suitable for an FAA type frangible coupling• Medium intensity, bi/uni-directional elevated threshold/endlight• Outer glass dome moulded in low expansion glass to resistthermal shock• Smooth outer glass surface resists build up of dirt and providesfor easier cleaning• All sub-assemblies are keyed to simplify routine maintenanceand ensure correct alignment• Robust corrosion resistant aluminium construction for strengthand durability• Gimble mounting for ease of alignment and levelling• Screws are stainless steel• Silicon rubber gaskets seal the dome against ingress ofliquids• Powder coat paint finish in golden yellow. All fasteners arestainless steel• IMM available on requestcompliance with standardsapplicationLow Intensity runway edge, turning circle taxiway and apron edge,heliport approach, FATO and TLOFoptions• ZS023 Sighting Device• Lamps:45w Pk30d100w Pk30d200w Pk30delectrical supplySuitable for use in 6.6A airfield lighting circuits, normally suppliedfrom either a 45W, 100W, or 200W series circuit isolating transformer.Power consumption varies depending upon type of lamp fitted.packaging dataNet weight 1.8kgGross weight 2.0kgCarton size 210mm(w) x 210mm(d) x 160mm(h)• ICAO Annex 14 Vol I: 5.3.17 Vol II: Fig 5.9• FAA AC150/534.5-48• CAA CAP168 Table 6A/1• NATO STANAG 3316• BSI BS3224 Part 4• CASA MOS 139 Chapter 9
<strong>IHR</strong> GmbH Hofmeister + Rumpfwww.ihr-aviation.netatg airports ltdAutomation House, Lowton Business Park, Newton Road, Lowton St. Mary’s, Warrington Wa3 2ap UKt +44 (0) 1942 68 5555 f +44 (0) 1942 68 5518 e products@atgairports.com w www.atgairports.com
Change language