Geared motors

Technical data - Shaft-mounted helical gearboxes (low-profile gearboxes)Permissible radial and axial forces - outputVCKSolid shaft with flangeApplication of force F r : Centre of shaft journal (x = I/2)F aTab only valid for F r = 0GFL 04 GFL 05 GFL 06 GFL 07 GFL 09 GFL 11 GFL 14n 2 F rTab F aTab F rTab F aTab F rTab F aTab F rTab F aTab F rTab F aTab F rTab F aTab F rTab F aTab[min -1 ] [N] [N] [N] [N] [N] [N] [N] [N] [N] [N] [N] [N] [N] [N]400 3200 2200 4300 3100 6100 4300 6400 6100 7800 6100 12500 6800 18000 6000250 3700 2600 5100 3900 7000 5500 7400 6500 9000 6500 14500 8500 20000 8000160 4400 3200 5900 4800 7800 6500 8900 7000 10500 7000 17000 10500 23000 10000100 4600 4200 6800 6400 9600 8500 10500 9500 14000 9500 21500 17000 27500 1300063 4600 4400 7000 6600 10000 10000 12000 11500 15000 11500 26000 22000 32000 1900040 4600 4400 7000 6600 10000 10000 13000 11500 15000 11500 30000 27000 38000 2600025 4600 4400 7000 6600 10000 10000 14000 11500 15000 11500 30000 27000 43000 35000≤ 16 4600 4400 7000 6600 10000 10000 14000 11500 15000 11500 30000 27000 43000 35000F r max 4600 – 7400 – 11000 – 16000 – 16000 – 32000 – 46000 –VòRSolid shaft without flangeApplication of force F r : Centre of shaft journal (x = I/2)F aTab only valid for F r = 0GFL 04 GFL 05 GFL 06 GFL 07 GFL 09* GFL 11* GFL 14n 2 F rTab F aTab F rTab F aTab F rTab F aTab F rTab F aTab F rTab F aTab F rTab F aTab F rTab F aTab[min -1 ] [N] [N] [N] [N] [N] [N] [N] [N] [N] [N] [N] [N] [N] [N]400 2300 2200 2400 2800 3200 4000 3200 3400 3800 3100 5500 4700 47000 25000250 2700 2600 2700 3600 3600 5200 3600 4700 4400 4200 6300 6000 54000 27000160 3200 3200 3200 4200 3900 6000 3900 6000 5500 5800 7300 7500 62000 29000100 3600 4200 4000 5900 5100 8500 5100 8500 8000 10000 11200 14000 65000 3200063 3600 5300 4800 6600 6500 10000 6500 12000 10000 13500 14500 19000 65000 3500040 3600 5500 5800 6600 8400 10000 8400 14000 12000 17000 17400 25000 65000 3500025 3600 5500 6200 6600 9000 10000 9000 14000 18000 21000 20500 27000 65000 35000≤ 16 3600 5500 6200 6600 9000 10000 9000 14000 18000 21000 23000 27000 65000 35000F r max 3600 – 7000 – 11000 – 11000 – 22000 – 28000 – 65000 –4HòòHollow shaftApplication of force F r : At hollow shaft end face (x = 0)F aTab only valid for F r = 0GFL 04 GFL 05 GFL 06 GFL 07 GFL 09 GFL 11 GFL 14n 2 F rTab F aTab F rTab F aTab F rTab F aTab F rTab F aTab F rTab F aTab F rTab F aTab F rTab F aTab[min -1 ] [N] [N] [N] [N] [N] [N] [N] [N] [N] [N] [N] [N] [N] [N]400 2800 2200 3000 2800 4300 4000 4500 3400 5000 3100 7300 4700 8000 4000250 3200 2600 3400 3600 4700 5200 5100 4700 6000 4200 8700 6000 9000 5000160 3800 3200 4100 4200 5000 6000 6400 6000 7200 5800 10000 7500 9500 6200100 4600 4200 5000 5900 6600 8500 7900 8500 10500 10000 14200 14000 11500 750063 5500 5300 6000 6600 8500 10000 9300 12000 13000 13500 19000 19000 14000 1100040 6300 5500 7100 6600 10800 10000 11500 14000 15000 17000 23000 25000 18000 1750025 7000 5500 8000 6600 12000 10000 15000 14000 22000 21000 27000 27000 30000 31000≤ 16 7000 5500 8000 6600 12000 10000 16000 14000 24000 21000 30000 27000 45000 35000F r max 7000 – 10000 – 15000 – 20000 – 30000 – 38000 – 56000 –* A reinforced output shaft bearing is available on request for VòR versions.Neither radial nor axial forces are permitted on hollowshafts with shrink disc (Sòò).G-motion const en 11/20044-3