maxicut 600 - Twose

More documents

Recommendations

Info

5299 7. MAINTENANCE 0306PROPER TORQUE FOR FASTENERSThe chart below lists the correct tightening torque for fasteners. When bolts are to be tightened orreplaced, refer to this chart to determine the grade of bolts and the proper torque except when specifictorque values are assigned in manual text.RECOMMENDED TORQUE IN FOOT POUNDS (NEWTON-METERS) UNLESS OTHERWISESTATED IN THE MANUALNOTE:These values apply to fasteners as received from supplier, dry or when lubricated withnormal engine oil. They do not apply if special graphited or molydisulphide greases orother extreme pressure lubricants are used. This applies to UNF fine, UNC coarsethreads, and metric fine and course threads.Proper torque values for imperial bolts(Figures in brackets are value in Nm)Proper Torque Values for Metric boltsBoltDiameterHeadMarkingNo MarksGrade TwoPound –Foot valueDryHeadMarkingThreeLinesGrade FivePound –Foot ValueDryHeadMarkingSix LinesGrade EightPound –Foot ValueDryBoltDiameterHeadMarking4.8Pound –Foot ValueDryHeadMarking8.8 or 9.8Pound –Foot ValueDryHeadMarking10.9Pound –Foot ValueDryHeadMarking12.9Pound –Foot ValueDry¼” 5.5(7.5) 9(12.2) 12.5(17.0) 6mm 4.5(6.1) 8.5(11.5) 12(16.3) 14.5(2.0)5/16” 11(15.0) 18(25.0) 26(35.2) 8mm 11(14.9) 20(27.1) 30(40.1) 35(47.5)3/8” 20(27.0) 33(45.0) 46(63.0) 10mm 21(28.5) 40(54.2) 60(81.4) 70(95)7/16” 32(43.0) 52(70) 75(100) 12mm 37(50.2) 70(95.0) 105(140) 120(160)½” 50(68.0) 80(110) 115(155) 14mm 60(81.4) 110(150) 165(225) 190(260)9/16” 70(95.0) 115(155) 160(220) 16mm 92(125) 175(240) 255(350) 300(400)5/8” 100(135) 160(220) 225(305) 18mm 125(170) 250(340) 350(475) 410(550)¾” 175(240) 280(380) 400(540) 20mm 180(245) 350(475) 500(675) 580(790)7/8” 175(240) 450(610) 650(880) 22mm 250(340) 475(645) 675(915) 800(1090)1” 270(360) 675(915) 975(1325) 24mm 310(420) <strong>600</strong>(810) 850(1150) 1000(1350)1-1/8” 375(510) 850(115) 1350(1830) 27mm 450(610) 875(1180) 1250(1700 1500(2000)1-1/4” 530(720) 1200(16250) 1950(2650) 30mm 625(850) 1200(1610) 1700(2300) 2000(2700)1-3/8” 700(950) 1550(2100) 2550(3460)1-1/2” 930(1250) 2100(2850) 3350(4450)*To get Newton-Metres multiply pound-foot of torque by 1.3567 - 7
5299 7. MAINTENANCE 0306HUB ASSEMBLYWhen attempting taper roller bearing adjustment it should be noted that there is not a specified torquesetting for the shaft crown nut since there should always be axial play (end float) with a taper rollerbearing set up.On the hub – stub axle set up the bearings are held axially by a wide base crown nut.With the double drilling of retention clip holes in the threaded shaft end a +45° to -45° adjustment ispossible in order to give maximum axial play (end float) on the bearings of 0.18mm.BEARING ADJUSTMENT1 Ensure that the spindle is clean and that the front bearing can slide on the front spindle. Fit backupspacer (washer)2 Fit the rear grease seal, rear bearing, hub and front bearing to the spindle (ensure front and reartaper roller bearings are packed with grease) and screw on the crown nut.3 Using the appropriate spanner ( a torque wrench is not required) tighten the crown nut whileturning the hub clockwise until the bearing friction begins to drag (the hub becomes difficult toturn, do not tighten to the point where the hub will not turn at all).4 Turn back the crown nut (anti clockwise) until the hole in the spindle and slot in the crown nut lineup, (if the hole and the slot line up at the point of tightening as in the previous paragraph it isessential that the crown nut is turned anti-clockwise until the hole and slot again line up.)5 Insert the retention pin and hook the bow spring into the appropriate groove in the crown nut.6 Check the adjustment by turning the hub clockwise. The hub should turn freely the only frictionshould be the rear grease seal.7 Partially fill the metal hub cap with grease and knock into position into the end of the hub.8 Recheck the bearing set up and hub grease content after 40 hours operation and then everyweek.7 - 8
Page 1: MAXICUTMaxicut 460Maxicut 600FLEX W
Page 4: 5299 2. TECHNICAL DATA 0306Tractor
Page 7 and 8: 5299 4. SAFETY 0306SafetyRead, Unde
Page 9 and 10: 5299 4. SAFETY 0306WARNING!WARNING!
Page 11 and 12: 5299 5. INSTALLATION 0306Preparing
Page 13 and 14: 5299 5. INSTALLATION 0306IMPORTANT
Page 15 and 16: 5299 6. OPERATION 0306HEIGHT OF CUT
Page 17 and 18: 5299 6. OPERATION 0306CUTTING TIPSA
Page 19 and 20: 5299 6. OPERATION 0306Check positio
Page 21 and 22: 5299 6. OPERATION 0306CAUTIONWARNIN
Page 23 and 24: 5299 7. MAINTENANCE 0306HITCH ASSEM
Page 25 and 26: 5299 7. MAINTENANCE 0306BLADE SERVI
Page 27: 5299 7. MAINTENANCE 03064 Set the e
Page 33 and 34: 5300 INDEX 0306MAXICUT 460 MOWERPAG
Page 35 and 36: 5300 CENTRE DECK & WING ASSEMBLIES
Page 37 and 38: 5300 CHAINGUARDS 0306REF PART NO DE
Page 39 and 40: 5300 BAFFLES 0306REF PART NO DESCRI
Page 41 and 42: 5300 SIDE SKIRTS & SKIDS 0306REF PA
Page 43 and 44: 5300 DRIVELINE GUARDS 0306REF PART
Page 45 and 46: 5300 HITCH & LEVELLING ASSEMBLY 030
Page 47 and 48: 5300 HIGH HITCH & LEVELLING ASSEMBL
Page 49 and 50: 5300 GEARBOXES & DRIVESHAFTS 0306RE
Page 51 and 52: 5300 HYDRAULIC RAM ASSEMBLIES 0306R
Page 53 and 54: 5300 HYDRAULIC FITTINGS AND HOSES 0
Page 55 and 56: 5300 WHEELS, HUBS AND AXLES 0306REF
Page 57 and 58: 5300 BLADE PAN ASSEMBLIES 0306REF P
Page 59 and 60: 5300 SHREDDER BLADE BAR ASSEMBLY 03
Page 61 and 62: 5300 LIGHTING ASSEMBLY 0306REF PART
Page 63: 5300 SAFETY DECALS 0306REF PART NO
Page 66 and 67: Publication 53010306Amendments0306
Page 68 and 69: Publication 53010306Maxicut 600STAN
Page 70 and 71: Publication 53010306Maxicut 600HIGH
Page 72 and 73: Publication 53010306Maxicut 600CENT
Page 74 and 75: Publication 53010306Maxicut 600CHAI
Page 76 and 77: Publication 53010306Maxicut 600AXLE
Page 78 and 79:
Publication 53010306Maxicut 6008 WH
Page 80 and 81:
Publication 53010306Maxicut 600LEVE
Page 82 and 83:
Publication 53010306Maxicut 600BLAD
Page 84 and 85:
Publication 53010306Maxicut 600GEAR
Page 86 and 87:
Publication 53010306Maxicut 600DRIV
Page 88 and 89:
Publication 53010306Maxicut 600DIVI
Page 90 and 91:
Publication 53010306Maxicut 600CENT
Page 92 and 93:
Publication 53010306Maxicut 600L/H
Page 94 and 95:
Publication 53010306Maxicut 600R/H
Page 96 and 97:
Publication 53010306Maxicut 600DRIV
Page 98 and 99:
Publication 53010306Maxicut 600SLIP
Page 100 and 101:
Publication 53010306Maxicut 600HYDR
Page 102 and 103:
Publication 53010306Maxicut 600HYDR
Page 104 and 105:
Publication 53010306Maxicut 600LIGH
Page 106 and 107:
Publication 53010306Maxicut 600MACH
show all

maxicut 600 - Twose

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?