Vulcan Tread Nosing, Steps and Tactile Produ... - Barbour Product ...

More documents

Recommendations

Info

Tactile bar forstone or concreteA25 mm6 mmB6 mm25 mmBDCTactile barfor carpet25 mm9 mmD25 mmC9 mmAVTac Bars are another part of the DDA range, manufactured by VulcanArchitectural. These bars are based on the Current standard sizes that arerequested for alerting users as to level changes, especially on stairwells.Whilst there is a difficulty being able to apply all the current legislationto Listed and Heritage buildings, the material that these products aremanufactured from are much more sympathetic with the character that thesebuildings portray. They have been found to be suitable for this application.*(*These decisions are subject to the approval from the Area listed buildingsofficer, and the client and tenant usage.)The fitting of these bars is guaranteed by the hidden studs along the length,underside (at point A) and a recess for the adhesive (at point B) to ensurethat there is no clack when the material is trodden on. The cross section of(C) shows the extra legs depth down the length of a carpet bar. These giveproduct stability around a central fixing.It is important that all DDA work is set out in accordance with the setguidelines to maintain regular consistent underfoot signals.Set out plates are available from Vulcan to assist in the correct dimensioning.Specification ExampleCorduroy or Blister Level Change Warning treatment to be provided by retro-fitting of 400(+/-)x20x6mm raised Stud or Bar fittings as manufactured by Vulcan Architectural. These are to befitted to 50mm spacing and, as per the guidance notes produced in accordance with DDA/PartM Regulations, to a depth of 800mm starting 400mm back from top/bottom of step/slope and400mm only on landing/turning areas. If steps/slopes are open sided, allowance is to be made forcoverage 400mm beyond the width of the steps each side. Material to be Stainless Steel/Brass/GRP Composite material in Standard Buff or red or special (any RAL colour)Vulcan: 020 8681 0617 sales@vulcanarchitectural.com23Sales: 020 8681 0617 • Email: sales@vulcansystems.co.uk
fitting studs & barsSubstrate preparation is of the utmost importance. Clean, dry & free ofany contaminants gives a satisfactory long lasting adhered bond. Vulcanrecommend to use a 2 part adhesion system at all times. All studs can beretrofitted. Fitting on stair edges prevents wearing of carpet on the frontleading edge. See page 23 for diagram of screw fixing through tactile bars (D).As always, compatibility between substrate and adhesive should be tested ona small unseen area to ensure suitability. Manufacturers’ recommendationand instruction should always be followed. Particular care must be takenwhen fixing through carpets.‘Sympathetic products forour local heritage sites’Local Authority, MidlandsBrass & Stainless Steel RangeGrooved anchor. Small amounts of adhesive to stop spinningGrooved or insert stud with 2 part adhesiveAnchor fitting for stair nosing carpet Stainless anchors Suitable for use in Listed or HeritageBuildings as Tactile awareness level changeor as step edging for a clear line of visionSales: 020 8681 0617 • Email: sales@vulcansystems.co.uk 24
Page 3 and 4: introductionWelcome to Vulcan’s t
Page 5 and 6: interior rangeThe current range of
Page 7 and 8: 82 mmVul 12578 mmVul 12455 mm37 mm9
Page 9 and 10: 60 mmVul 14255 mm60 mmVul 143DDAPro
Page 11: ‘Fabulously strong & they look gr
Page 14 and 15: angeThe highest quality nosing for
Page 16 and 17: 60 mmVul 4022mm Stainless Steel 316
Page 18 and 19: ICEBERG ®The tip of stair lighting
Page 20 and 21: angeSide trimsAvailable in 3 styles
Page 22 and 23: metal processing & finishesAluminiu
Page 26 and 27: Vulcan supply a large range of Tact
Page 28 and 29: A permanent, integrated step insert
Page 30 and 31: 12 mm 12 mm12mm double square inser
Page 32 and 33: exterior rangeA superior fibreglass
Page 35 and 36: VulcaGR!P insert C25 YellowHousing
Page 37 and 38: ‘You can quote me on this.Those t
Page 39 and 40: 55 mm12 7103555 mm4DDAProductVul 13

Vulcan Tread Nosing, Steps and Tactile Produ... - Barbour Product ...

Create successful ePaper yourself

Delete template?

Save as template?