2 Relief ValvesSeries 1L, 1XL, 10L and 100XL ( 1 ⁄2" , 3 ⁄4")Self-closing T&P Safety Relief Valves for Hot Water StorageTanks and Heaters• These combined two-in-one Temperature and Pressure relief valves provide theleast expensive and proven means for protection against both excessive temperatureand pressure emergency conditions.• Fully automatic temperature and pressure relief protection for domestic hot watersupply tanks and heaters based on the latest ANSI Z21.22 listing requirements fortemperature discharge capacity.• Reliable and proven means of protection against excessive temperature and pressurebuild-up in domestic hot water systems.A• Includes test lever.• For water heaters from 15,000 to 105,000 BTU/hr.• NPT male inlet and female outlet.Note: See pg. 25 for information on domesticexpansion tanks (DET) to control thermalexpansion in domestic water closed systems.For additional information,request literature ES-10L, ES-100XL,ES-SL100XL/L100XL/LL100XL/ LLL100XL.BTD100XLStandards• ANSI Z21.22 and ASME Section IVRated † , CSA Listed.Specifications• Temperature Relief: 210°F (99°C).Pressure Relief Range: 75 – 150psi(5.2 – 10.3 bars). Standard PressureRelief Settings: 75psi (517.1 kPa),100psi (6.9 bars), 125psi (8.6 bars) or150psi (10.3 bars).MODEL SIZE (DN) DIMENSIONS (APPROX.) WEIGHT CSAA B D T Temp. Steamin. mm in. mm in. mm in. mm in. mm oz. gm. Rating BTU/hr.1L2 † 1 ⁄2 15 1 3 ⁄4 43 3 1 ⁄2 89 7⁄8 22 2 50 10 284 15,0001XL † 1 ⁄2 15 1 3 ⁄4 43 3 1 ⁄2 89 7⁄8 22 3 76 12 340 15,0001XL-8 † 1 ⁄2 15 1 3 ⁄4 43 3 1 ⁄2 89 7⁄8 22 8 203 16 454 15,00010L-2 3⁄4 20 1 3 ⁄4 43 3 1 ⁄2 89 1 1 ⁄8 29 2 50 10 284 80,000100XL 3⁄4 20 1 3 ⁄4 43 3 1 ⁄2 89 1 1 ⁄8 29 3 76 12 340 100,000100XL-8 3⁄4 20 1 3 ⁄4 43 3 1 ⁄2 89 1 1 ⁄8 29 8 203 14 397 100,000L100XL-3 3⁄4 20 1 3 ⁄4 43 4 1 ⁄4 108 2 1 ⁄8 41 3 76 12 340 100,000SL100XL** 3⁄4 20 1 3 ⁄4 43 4 3 ⁄8 111 1 1 ⁄4 32 3 1 ⁄2 89 12 340 105,000LL100XL 3⁄4 20 1 3 ⁄4 43 4 3 ⁄4 121 2 50 2 1 ⁄2 64 12 340 100,000LLL100XL-Z5** 3⁄4 20 1 3 ⁄4 43 5 1 ⁄4 133 2 1 ⁄2 64 2 1 ⁄8 54 12 340 105,000A = overall width of the valve. B = overall height of the valve, with lever closed, not including thermostat element length. D = length of shank , fromshoulder under outlet orifice overhang to inlet orifice edge. T = length of thermostat element, measured from inlet orifice edge to end of thermostat.Set @ 150psi (10.3 bars). Consult your local Watts Agent or call Customer Service at (978) 689-6066 for ordering codes of valves with pressurerelief settings of 75, 100, 125psi (5.2, 6.9, 8.6 bars).**CSA rating 105,000 BTU†1⁄2" (15mm) valves are not ASME rated.Model 210 ( 3 ⁄4")Immersion-type, Temperature Gas Shutoff for HotWater Storage Heaters.• Protects against excessive temperaturesin gas water heaters.• Shuts off the gas supply to the waterheater in the event that the watertemperature reaches 210°F (98.9°C).• Used in conjunction with Model 3Lpressure relief valve, p.20.Specifications• Tank connection 3 ⁄4" (20mm) NPT male.• Gas inlet and outlet connection 1 ⁄2"(15mm) NPT female.• Design certified by CSA.• CSA ratings: natural gas 150,000BTU/hr., liquefied petroleum gas243,000 BTU/hr.For additional information,request literature ES-210.21024For assistance, contact your local authorized Watts agent or visit our website at www.wattsreg.com
ASME Rated Series 40, 140,240, 340, 342 ( 3 ⁄4" – 2")Automatic Reseating T&P Relief Valves for Hot Water SupplyTanks and Heaters.• The combined two-in-one Temperature and Pressure relief valve provides the leastexpensive and most proven means for protection against both excessive temperatureand pressure.• Fully automatic temperature and pressure relief protection for hot water supplytanks and heaters based on the latest ANSI Z21.22 Listing Requirements for temperaturedischarge capacity.StandardsANSI Z21.22 and ASME Section IV Rated, CSA Listed.3402Relief ValvesSpecifications• Temperature relief 210°F (98.9°C). Pressure range 75 – 150psi (5.2 – 10.3 bars).Standard settings: 75psi (517.1 kPa); 100psi (6.9 bars); 125psi (8.6 bars); and150psi (10.3 bars). See Dimensions/Wgts. chart on next page for inlet and outletconnection type and sizes.Series 40, 140 nominal size 3 ⁄4" (20mm)• To protect gas, electric or oil-fired storage water heaters rated between 180,000 to200,000 BTU/Hr. from excessive heat or pressure build up, choose the 3 ⁄4" (20mm)model 40 or 140. Tested under ANSI Z21.22 with ratings as certified and listed byCSA. Series 40, 140 and 240 nominal size 1" (25mm).• For gas or oil-fired storage water heaters rated between 450,000 and 730,000BTU/Hr., choose the 1" (25mm) model 40, 140 or 240. Tested under ANSI Z21.22with ratings as certified and listed by CSA.Series 340, 342 nominal sizes 1 1 ⁄2" x 2" (40 x 50mm)• For gas or oil-fired hot water supply boilers rated over 730,000 BTU/Hr. outputheating for water and for steam coil storage water heaters, choose the Model 340or 342. Tested under ANSI Z21.22 with ratings as certified and listed by CSA.Features• Bronze body construction• Tamper-resistant bonnet screws• Series 40 and 140 feature a uniquethermostat with a special thermobondedcoating• 1" (25mm) and above sizes Model M2,M4 and M14 are standardly furnishedwith stainless steel thermostat tube• Accurate and proven thermostat,exclusively designed and manufacturedby WattsSpecial ModelSpecial Model 340X-8 M4Z available in 1 1 ⁄2" (40mm) size only. Pressure setting is175psi (12.1 bars). Temperature relief at 210°F (98.9°C); Certified by CSA only.For additional information, request literature ES-40, 140, 240, 340, or ES-LL/LLL-40XL.For assistance, contact your local authorized Watts agent or visit our website at www.wattsreg.com25
- Page 3 and 4: Watts Regulator CompanySince 1874 W
- Page 5 and 6: Series 25AUB ( 1 ⁄2" - 2")Standar
- Page 7 and 8: Series N45B ( 1 ⁄2" - 1")Water Pr
- Page 9 and 10: Series N45B-EZ ( 1 ⁄2" - 1")Water
- Page 11 and 12: Series N55B (1 1 ⁄4" - 2")Water P
- Page 13 and 14: Series 223, 223S ( 1 ⁄2" - 2 1
- Page 15 and 16: Series N250 ( 1 ⁄2", 3 ⁄4")Iron
- Page 17 and 18: Series 26A, 263A ( 1 ⁄8" - 1 ⁄2
- Page 19 and 20: Series 127 ( 1 ⁄2" - 4")Process S
- Page 21 and 22: Series 740 ( 3 ⁄4" - 2")Iron Body
- Page 23: Fig. 31 ASME Section I Series Valve
- Page 27 and 28: Series 3L, 53L ( 1 ⁄2", 3 ⁄4")P
- Page 29 and 30: Spacemaker ® by WattsOutside Water
- Page 31 and 32: Spacemaker ® by WattsWater Heater
- Page 33 and 34: Series DETA 5 - DETA 210ASME Pressu
- Page 35 and 36: Series PVS-1000Pre-engineered Valve
- Page 37 and 38: SilverEagle Series 757a,757Na (2 1
- Page 39 and 40: Series 709 (2 1 ⁄2" - 10")Double
- Page 41 and 42: GoldenEagle Series 719 ( 1 ⁄2" -
- Page 43 and 44: SilverEagle Series 757DCDA,757NDCDA
- Page 45 and 46: Series 774DCDA (2 1 ⁄2" - 12")Ser
- Page 47 and 48: Series 007DCDA (2" - 3")Double Chec
- Page 49 and 50: Series 994 (2 1 ⁄2" - 10")Reduced
- Page 51 and 52: Series 909 ( 3 ⁄4" - 2")Reduced P
- Page 53 and 54: Series 009 ( 1 ⁄4" - 3")Reduced P
- Page 55 and 56: Copperhead ® Series 995 ( 1 ⁄2"
- Page 57 and 58: Series 994RPDA (2 1 ⁄2" - 6")Redu
- Page 59 and 60: Air Gaps and Elbowsfor Reduced Pres
- Page 61 and 62: Series 008PCQT ( 3 ⁄8" - 1")Spill
- Page 63 and 64: Series 8 ( 3 ⁄8" - 3 ⁄4")Hose C
- Page 65 and 66: Series SS07F (4" - 10")Stainless St
- Page 67 and 68: Series B6000 ( 1 ⁄4" - 4")B6001 (
- Page 69 and 70: Series B6080, B6081 ( 1 ⁄2" - 2")
- Page 71 and 72: Series B6004 ( 1 ⁄2" - 1")Standar
- Page 73 and 74: Series B6000-CC ( 1 ⁄2" - 3 ⁄4"
- Page 75 and 76:
Series WBV-3, WBVS-3 ( 1 ⁄8" - 4"
- Page 77 and 78:
Series B-3000, B-3001 ( 1 ⁄2" - 2
- Page 79 and 80:
Series 6 ( 1 ⁄4" - 1")Brass Midi
- Page 81 and 82:
Series F-511 (2" - 10")Class 125, I
- Page 83 and 84:
Series ECV, LCV, NCV, MFCV ( 3 ⁄4
- Page 85 and 86:
Series 77F-BI (2" - 8")Bronze, Flan
- Page 87 and 88:
Series 97FB-CI (2" - 12")Cast Iron,
- Page 89 and 90:
Series CSM-61 ( 1 ⁄2" - 3")Flow M
- Page 91 and 92:
Series DBF (2" - 12"), BF (2" - 48"
- Page 93 and 94:
Series 1156F, 1450F ( 1 ⁄2")Feed
- Page 95 and 96:
Series ET-RA 35 - ET-RA 2000ASME Pr
- Page 97 and 98:
Series AS, AS-T (1" - 3")Air Scoops
- Page 99 and 100:
Series 2000-M5 ( 3 ⁄4" - 3")Hydro
- Page 101 and 102:
Series WFTC ( 3 ⁄4" - 1 1 ⁄4"),
- Page 103 and 104:
Series 142, 144 ( 1 ⁄2")Boiler Wa
- Page 105 and 106:
Series USG-B ( 3 ⁄8")Under Sink G
- Page 107 and 108:
Series 1170, L1170 ( 1 ⁄2" - 1")H
- Page 109 and 110:
Series ZRO-4ZeroWaste Reverse Osmos
- Page 111 and 112:
WM SeriesCommercial / Industrial Re
- Page 113 and 114:
Series 05 ( 1 ⁄8" - 3 ⁄4")Mini
- Page 115 and 116:
Series 2-M2 ( 1 ⁄2")Duo-Cloz Wash
- Page 117 and 118:
Series FH, FHB ( 1 ⁄2" x 1 ⁄2",
- Page 119 and 120:
Tube Fitting Mini Cooler ValvesBras
- Page 121 and 122:
MODEL SIZE (DN) DIMENSIONS (APPROX.
- Page 123 and 124:
Model CIC-P ( 1 ⁄4 " )Flexible, R
- Page 125 and 126:
Series DPG1 (2" - 4")Bottom Entry P
- Page 127 and 128:
Series DPG5 (2" - 3")Top Entry Pres
- Page 129 and 130:
Series TBP (2 1 ⁄2")Pipe Mount Bi
- Page 132:
For Technical Assistance Call Your