CE - White Drive Products, Inc.

CE
400 & 401 SerieS technical information
Bearing Curve: the bearing curve represents allowable bearing loads
based on ISO 281 bearing capacity for an L 10 life of 2,000 hours at 100
rpm. Radial loads for speeds other than 100 rpm may be calculated
using the multiplication factor table located on page 15.
wheel mount
10
-75 -50 -25 0 25 50 75 100 125 mm
8,000
3,500
7,000
6,000
5,000
4,000
3,000
2,000
1,000
lb
ShaftS
Bearing
445 dan [1000 lbs]
445 dan [1000 lbs]
Shaft
-3 -2 -1 0 1 2 3 4 5 in.
20 1-1/4” Straight
Max. Torque: 1200 Nm [10600 lb-in]
8,0 [.314]
8,0 [.313]
35,3 [1.388]
35,0 [1.376]
34 [1.33]
wire ring
7,0 [.276]
7,0 [.274]
23 1-1/4” 14 Tooth Spline
Max. Torque: 1200 Nm [10600 lb-in]
wire ring
34 [1.33]
14 tooth 12/24 pitch
Std. ANSI B92.1-1996 Spline
21 [.83] min.
31,8 [1.250]
31,7 [1.249]
5/8”-18 UNF
21 [.83] min.
8 [.32]
31,7 [1.249]
31,6 [1.245]
*102 [4.03]
54 [2.14]
48 [1.90]
Ø 2 [.06]
wire ring
*102 [4.03]
48 [1.90]
41 [1.60] min.
5/8”-18 UNF
Ø 2 [.06] wire ring
NOTE: * Shaft lengths may vary by ± 0,8mm [.030 in].
15°
37,5 [1.475]
36,2 [1.425]
15°
mounting
flange
mounting
flange
3,000
2,500
2,000
1,500
1,000
500
dan
DELIVERING THE POWER TO GET WORK DONE
whitedriveproducts
22 1-1/4” Tapered
LENGTH / WEIGHT CHART
Wheel Mount - Dimension KK
Code mm [in] kg [lb]
120 99 [3.91] 10,9 [24.1]
160 99 [3.91] 10,9 [24.1]
200 103 [4.05] 11,3 [24.8]
230 105 [4.15] 11,4 [25.2]
260 108 [4.24] 11,6 [25.6]
300 111 [4.37] 11,9 [26.3]
350 125 [4.92] 13,1 [28.8]
375 117 [4.62] 12,4 [27.4]
470 125 [4.92] 13,1 [28.8]
540 131 [5.16] 13,6 [30.0]
750 149 [5.87] 15,0 [33.1]
NOTE:
CE motor weights vary ± 0,5 kg [1 lb] depending upon motor
configuration.
Max. Torque: 1200 Nm [10600 lb-in]
*100 [3.94]
8,0 [.314]
8,0 [.313]
5 [.20]
4 [.17]
19 [.75]
35 [1.37]
4 [.15]
7,0 [.276]
7,0 [.274]
31,8 [1.250]
31,7 [1.248]
1”-20 UNEF
1:8 taper
mounting
flange
24,3 [.957]
23,0 [.907]