CE - White Drive Products, Inc.

More documents

Recommendations

Info

CE 420 & 421 SerieS houSingS (wheel mount) 12 13,3 [.524] 13,1 [.514] *88,8 [3.498] *88,7 [3.494] DELIVERING THE POWER TO GET WORK DONE whitedriveproducts W31 4-Hole 7/8” O-Ring Aligned Ports W35 4-Hole 9/16” O-Ring Aligned Ports W38 4-Hole 1/2” BSP.F Aligned Ports P31 4-Hole 7/8” O-Ring Aligned Ports P38 4-Hole 1/2” BSP.F Aligned Ports 7,000 6,000 5,000 4,000 3,000 2,000 1,000 lb 45° 131 [5.15] max. 63 [2.49] min. NOTE: * the p31 & p38 pilot diameter is 82,5 [3.248]. 138 [5.45] max. Ø 147,6 [5.812] 23 [.90] Bearing Curve: the bearing curve represents allowable bearing loads based on ISO 281 bearing capacity for an L 10 life of 2,000 hours at 100 rpm. radial loads for speeds other than 100 rpm may be calculated using the multiplication factor table located on page 15. wheel mount -75 -50 -25 0 25 50 75 100 125 mm 8,000 3,500 445 dan [1000 lbs] 445 dan [1000 lbs] Bearing Shaft -3 -2 -1 0 1 2 3 4 5 in. 3,000 2,500 2,000 1,500 1,000 500 dan 44,3 [1.743] 44,1 [1.738] 23 [.90] Shaft 18 [.72] 22 1-1/4” Tapered 46 [1.48] Max. Torque: 1200 Nm [10600 lb-in] 8,0 [.314] 8,0 [.313] 4 [.15] 7,0 [.276] 7,0 [.274] LL 3 [.10] min. LENGTH / WEIGHT CHART Wheel Mount - Dimension LL Code mm [in] kg [lb] B A 31,5 [1.241] 31,5 [1.240] 19 [.76] 5 [.20] 4 [.17] 1”-20 UNEF 1:8 Taper 120 99 [3.91] 10,9 [24.1] 160 99 [3.91] 10,9 [24.1] 200 103 [4.05] 11,3 [24.8] 230 105 [4.15] 11,4 [25.2] 260 108 [4.24] 11,6 [25.6] 300 111 [4.37] 11,9 [26.3] 350 125 [4.92] 13,1 [28.8] 375 117 [4.62] 12,4 [27.4] 470 125 [4.92] 13,1 [28.8] 540 131 [5.16] 13,6 [30.0] 750 149 [5.87] 15,0 [33.1] *108 [4.26] 127,0 [4.999] 126,8 [4.994] 35 [1.37] NOTE: * Shaft lengths may vary by ± 0,8mm [.030 in]. NOTE: CE motor weights vary ± 0,5 kg [1 lb] depending upon motor configuration. Mounting Flange 22,6 [.890] 22,4 [.880]
whitedriveproducts DELIVERING THE POWER TO GET WORK DONE CE 420 & 421 SERIES mOdEL COdE BUILdER SERIES DISPLACEMENT HOUSING SHAFT PAINT CAVITY ADD ON MISCELLANEOUS STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6 STEP 7 STEP 8 STEP 1 - Select a series 420 421 Counterclockwise Rotation Clockwise Rotation STEP 2 - Select a displacement option 120 160 200 230 260 300 STEP 3 - Select a housing option W31 W35 W38 P31 P38 B A B A 420 421 NOTE: For applications requiring the motor to rotate in only one direction, shaft seal life may be prolonged by pressurizing the “A” port of the motor. To obtain the desired direction of shaft rotation, use the graphic above to determine the rotation code for the motor. For bi- directional applications, the 420 series is recommended. Preferred rotation is determined by internal valving design. 121 cc [7.4 in3/rev] 162 cc [9.9 in3/rev] 204 cc [12.4 in3/rev] 232 cc [14.2 in3/rev] 261 cc [15.9 in3/rev] 300 cc [18.3 in3/rev] 350 375 470 540 750 348 cc [21.2 in3/rev] 375 cc [22.8 in3/rev] 465 cc [28.3 in3/rev] 536 cc [32.7 in3/rev] 748 cc [45.6 in3/rev] 4-Hole 7/8” O-Ring Aligned Ports, 88.75 [3.496] Pilot 4-Hole 9/16” O-Ring Aligned Ports, 88.75 [3.496] Pilot 4-Hole 1/2” BSP.F Aligned Ports, 88.75 [3.496] Pilot 4-Hole 7/8” O-Ring Aligned Ports, 82.5 [3.248] Pilot 4-Hole 1/2” BSP.F Aligned Ports, 82.5 [3.248] Pilot STEP 4 - Select a shaft option 22 STEP 5 - Select a paint option A B Z 1-1/4” Tapered Black Black (unpainted flange face) No Paint STEP 6 - Select a valve cavity option A STEP 7 - Select an add on option A B C Standard Lock Nut Solid Hex Nut STEP 8 - Select a miscellaneous option AA AC AE None None Freeturning Rotor Hydraulic Declutch with Freeturning Rotor 13
Page 1 and 2: CE SERIES HYDRAULIC MOTORS
Page 3 and 4: flow - lpm [gpm] max. cont. max. in
Page 5 and 6: whitedriveproducts 261 cc [15.9 in
Page 7 and 8: whitedriveproducts 465 cc [28.3 in
Page 9 and 10: whitedriveproducts W31 4-Hole 7/8
Page 11: whitedriveproducts DELIVERING THE P
Page 15 and 16: 28 35mm tapered Max. Torque: 1200 N
Page 17 and 18: K31 K35 K38 114 [4.49] NN 138 [5.45
Page 19 and 20: Important Information Before select

CE - White Drive Products, Inc.

Create successful ePaper yourself

Delete template?

Save as template?