Series AC Inverters User's Manual

Recommendations

Info

Section 4: ConnectionsPull-Up LogicShieldForwardReverseIncreaseDecreaseE-Stop21-Mode = 6 or 7J20Pull-Down Logic(Note 2) (Note 2)E-StopShieldCMCMFWDForwardFWDREVReverseREVPS3PS3PS2IncreasePS2PS1DecreasePS1V+ V+MOL21-Mode = 6 or 7MOLJ20Figure 19: EMOP SelectionShield–V+Shield–I+CMMET1CMMET2(Note 3)Notes:1. See Table 10 on page 19.2. See page 52, 21-MODE. 21-MODE = 6 used for2-wire operation. 21-MODE = 7 used for 3-wireoperation.3.For MET1, see 71-METER on page 64. ForMET2, see 79-MET2 on page 67.Figure 20: Analog MeterToUserOutputDeviceShieldCMNORCMNCShieldCR1CMV+ST1Figure 21: Relay STRFigure 22: Logic Output ST132© 1998 TB Wood’s All Rights Reserved
Section 5: RFI Suppression and XLF Line Filters5.1 IntroductionThis section contains speciÞcations, installation, and operationinstructions for TB WoodÕs XLF Series line Þlters. Proper installation ofthe XLF Series Þlters in the correct model of X2C Series inverter will aidin complying with CE (ConformitŽ EuropŽen) EMC directives. TheseÞlters limit emissions per EMC Directive 89/336 EEC to meet thefollowing speciÞcations:Table 9: EMA (Electromagnetic Emission) SpecificationsEN 50081-1EN 55011EN 55014Basic specification, “Emitted Interference”Emitted Interference - Industrial, Scientific and Medical InstallationsEmitted Interference - Residential InstallationsTable 10: EMB (Electromagnetic Interference) SpecificationsEN 50082-2EN 50140EN 60801ENV 50142IEC 801-4Basic specification, “Interference Immunity”Electromagnetic FieldsStatic DischargeSurgeBurst on mains lead/data lineTo ensure compliance with the CE directive, observe the followingprocedures:1. Install a line Þlter on a properly-matched X2C inverter.2. To meet the B Curve for EMC (commercial) compliance, anoutput reactor may also be required. No output Þlter or reactor isrequired to meet the A Emission Curve for EMC (Industrial)compliance (reduces leakage current to a level below 3.5 mA).3. Install shielded motor cable and correctly ground the shield.4. Observe general RFI suppression measures. Refer toÒInterference Suppression Measures,Ó on pages 38-40.NOTE: XLF Series line Þlters do not bear the CE mark. Although the Þltershave been tested with the inverters for compliance, installation practices andother wiring concerns make CE compliance with EMC directives theresponsibility of the installer of the equipment. In addition, motor outputwiring considerations required to meet the CE directives are presented inÒInterference Suppression MeasuresÓ on pages 38 to 40. XLF Series line Þltersare not UL listed or recognized. If local codes permit, the Þlters may be used inthe United States as a solution for EMI and RFI problems either caused by oraffecting the operation of an X2C series inverter.© 1998 TB Wood’s All Rights Reserved 33
Page 1 and 2: ®Form 1247A®X2CSeries AC Inverter
Page 3 and 4: Table of ContentsSECTION 1: INTRODU
Page 5 and 6: Table of ContentsSECTION 8: PI CONT
Page 7 and 8: Section 1: Introduction1.1 Scope of
Page 9 and 10: Section 2: Specifications2.1 Model
Page 11 and 12: Section 2: SpecificationsTable 2: P
Page 13 and 14: Section 2: Specifications5.50(140)5
Page 15 and 16: Section 2: Specifications2.4 Power
Page 17 and 18: Section 3: Receiving and Installati
Page 19 and 20: Section 3: Receiving and Installati
Page 21 and 22: Section 4: ConnectionsDANGERHAZARDO
Page 23 and 24: Section 4: Connections4.2 Power Ter
Page 25 and 26: Section 4: Connections4.3 Control T
Page 27 and 28: Section 4: Connections4.4 J20 Confi
Page 29 and 30: Section 4: Connections4.6 Input Lin
Page 31 and 32: Section 4: Connectionsinstallations
Page 33 and 34: Section 4: ConnectionsD. Control Wi
Page 35 and 36: Section 4: ConnectionsPull-Up Logic
Page 37: Section 4: ConnectionsPull-Up Logic
Page 41 and 42: Section 5: RFI Suppression and XLF
Page 47 and 48: Section 6: Getting Started6.1 Intro
Page 49 and 50: Section 6: Getting StartedProgram m
Page 51 and 52: Section 6: Getting StartedSymbolFWD
Page 53 and 54: Section 6: Getting Started6.6 Quick
Page 55 and 56: Section 7: Parameter Configuration
Page 79 and 80: Section 8: PI Controller8.1 Introdu
Page 81 and 82: Section 8: PI ControllerThe PI Cont
Page 83 and 84: Section 8: PI ControllerActual outp
Page 85 and 86: Section 8: PI ControllerB. Paramete
Page 87 and 88: Section 8: PI Controller81-PRGNO (P
Page 89 and 90:
Section 9: TroubleshootingWARNINGHA
Page 91 and 92:
Section 9: Troubleshooting9.4 Fault
Page 93 and 94:
Section 10: Options and Replacement
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Appendix A: Summary of X2C Paramete
Page 101 and 102:
Appendix A: X2C Parameter SummaryPa
Page 103 and 104:
Appendix B: EU Declaration of Confo
Page 105 and 106:
Publication HistoryDateMarch 1998 F
show all

Series AC Inverters User's Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?