68 05 19 removing and installing inner door sill trim

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 6: Removing inner door sill trim in area of C-pillar (1 Of 3)Courtesy of PORSCHE OF NORTH AMERICA, INC.6. Unclip inner door sill trim in area of C-pillar6.1. Unclip and lift rear side trim panel -6- in area of overlap. Unclip inner door sill trim -1- . See Fig. 8, Fig. 6.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 8: Removing inner door sill trim in area of C-pillar (3 Of 3)Courtesy of PORSCHE OF NORTH AMERICA, INC.INSTALLING INNER DOOR SILL TRIMInstalling inner door sill trimInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 10: Check clips for deformationCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Check clips.1.1. Check clips -7- for deformation; replace if necessary. See Fig. 10.Installation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 11: Installation location of inner door sill trimInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 13: Insert inner door sill trim in area of overlap under rear side trim paneCourtesy of PORSCHE OF NORTH AMERICA, INC.2.1. Insert inner door sill trim -1- in area of overlap under rear side trim pane -6- . See Fig. 13.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 15: Positioning marking mandrel for inner door sill trim on inner B-pillarCourtesy of PORSCHE OF NORTH AMERICA, INC.2.3. Position marking mandrel -5- for inner door sill trim -1- on inner B-pillar. See Fig. 15.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 17: Clip rear trim into scuff plate from rear to frontCourtesy of PORSCHE OF NORTH AMERICA, INC.4. Clip in rear trim.4.1. Clip rear trim -3- into scuff plate from rear to front. See Fig. 17.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 18: Clip front trim into scuff plate from rear to frontCourtesy of PORSCHE OF NORTH AMERICA, INC.5. Clip in trim.5.1. Clip front trim -2- into scuff plate from rear to front. See Fig. 18.6. Install B-pillar trim. Refer to 70 67 19 Removing and installing B-pillar trim panel - as of MY 2003 (AllModels) .68 11 19 REMOVING AND INSTALLING GLOVE COMPARTMENT LOCK - ASOF MY 2003 (ALL MODELS)REMOVING LOCK, RELEASE AND LOCK CYLINDER FOR GLOVE COMPARTMENTRemoving glove compartment lockInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 19: Installation location of glove compartment lock1. Remove trim strip for dashboard on passenger's side. Refer to 70 58 19 Removing and installing trim stripfor the dashboard on the passenger's side - as of MY 2003 (All Models) .2. Remove cover under dashboard on the passenger's side. Refer to 70 22 19 Removing and installing coverunder dashboard - as of MY 2003 (All Models) .3. Remove glove compartment --> 681519 Removing and installing glove compartment - "Removing"4. Remove glove compartment lock.4.1. Unscrew and remove fastening screw -1- . See Fig. 20.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 20: Removing glove compartment lock (1 Of 2)Courtesy of PORSCHE OF NORTH AMERICA, INC.4.2. First swivel lock -2- to the right -Arrow A- and then to the front ( -Arrow B- ). See Fig. 20.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 21: Removing glove compartment lock (2 Of 2)Courtesy of PORSCHE OF NORTH AMERICA, INC.4.3. Remove lock -2- with actuating cable -3- and lock bolt -11- rearward through the dashboard mounting ( -Arrow C- ). See Fig. 21.5. Remove actuating cable from lock. --> 681119 Removing and installing glove compartment lock -"Removing"Removing actuating cable for lockInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 22: Installation location of glove compartment lock1. Remove glove compartment --> 681519 Removing and installing glove compartment - "Removing"2. Remove glove compartment lock. --> 681119 Removing and installing glove compartment lock -"Removing"3. Remove actuating cable from lock.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 23: Removing actuating cable for lock (1 Of 2)Courtesy of PORSCHE OF NORTH AMERICA, INC.3.1. Detach cable -6- from actuating lever -7- . To do this, swivel the cable by approx. 90° to the assemblyopening of the actuating lever -Arrow A- and remove it in an upward direction ( -Arrow B- ). See Fig. 23.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 24: Removing actuating cable for lock (2 Of 2)Courtesy of PORSCHE OF NORTH AMERICA, INC.3.2. Compress fixing clips of cable mounting -4- on lock -5- -Arrows C- and pull the cable mounting out ofholder ( -Arrow D- ). Remove actuating cable from lock. See Fig. 24.Installation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 25: Installation location of actuating cable at lock4. Remove actuating cable from lock bolt.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 26: Remove actuating cable (1 Of 3)Courtesy of PORSCHE OF NORTH AMERICA, INC.4.1. Compress fastening clips -8- of cap -9- towards center -arrows E- and remove cap. See Fig. 26.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 27: Remove actuating cable (2 Of 3)Courtesy of PORSCHE OF NORTH AMERICA, INC.4.2. Detach cable -6- from actuating lever -12- . To do this, swivel the cable by approx. 90° to the assemblyopening of the actuating lever -arrow F- and remove it in an upward direction. See Fig. 27.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 28: Remove actuating cable (3 Of 3)Courtesy of PORSCHE OF NORTH AMERICA, INC.4.3. Compress fastening clips of cable mounting -10- on lock bolt -11- -arrows G- and pull the mounting out ofholder ( -arrow H- ). Remove actuating cable on the lock catch bolt. See Fig. 28.Removing lock cylinderInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 29: Installation location of glove compartment lock1. Remove glove compartment --> 681519 Removing and installing glove compartment - "Removing"2. Remove glove compartment lock. --> 681119 Removing and installing glove compartment lock -"Removing"3. Remove actuating cable from lock. --> 681119 Removing and installing glove compartment lock -"Removing"

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 30: Removing lock cylinder (1 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.4. Remove cover.4.1. Unclip cover -1- from lock mount -2- using a small screwdriver -3- and lift off ( -arrow A- ). See Fig. 30.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 31: Removing lock cylinder (2 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.CAUTION: Danger of material damage in the event of incorrect removal andinstallation of lock cylinder.--> The ignition key must not be withdrawn from the lock cylinder when removing the lock cylinder from orinstalling it into the lock, as otherwise the spring-loaded locking elements will spring out of the lock barrel.--> If the ignition key is withdrawn with the lock cylinder removed, the locking elements must be held in onboth sides with the fingers until the ignition key is fully out of the lock cylinder. The locking elements can thenbe carefully relaxed and the lock cylinder laid down.--> Lock cylinders supplied as spare parts are secured in a transport case.5. Remove lock barrel.• In the event of incorrect removal and installation, the lock cylindercan be damaged.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 32: Removing lock cylinder (3 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.5.1. Fully insert ignition key -4- into lock cylinder -5- -arrow B- . This locks the locking elements -8- in thelock cylinder. See Fig. 32, Fig. 34.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 33: Removing lock cylinder (4 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.5.2. Turn ignition key -4- counter-clockwise as far as possible -arrow C- and hold the pretension. This keepsthe ignition key tensioned in the lock barrel so that it cannot be withdrawn. See Fig. 33.5.3. Force retaining clips -6- of lock cylinder -5- outwards with a small screwdriver ( -arrows D- ). See Fig. 33.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 34: Removing lock cylinder (5 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.5.4. Withdraw lock cylinder -5- together with ignition key -4- from the lock -arrow E- and remove. See Fig.34.INSTALLING LOCK, RELEASE AND LOCK CYLINDER FOR GLOVE COMPARTMENTInstalling glove compartment lockInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 35: Installation location of glove compartment lock1. Install actuating cable on lock. --> 681119 Removing and installing glove compartment lock -"installing"NOTE:Once it is fitted correctly on the dashboard mounting, the lock can no longer bemoved vertically or to the left or right.2. Install glove compartment lock.2.1. Insert lock bolt with actuating cable from the front through the dashboard mounting.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 36: Inserting lock into dashboard mountingCourtesy of PORSCHE OF NORTH AMERICA, INC.2.2. Insert lock -2- into dashboard mounting -13- -arrow A- and align it until it is resting evenly against themounting. See Fig. 36.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 37: Pushing lock as far as possible until retaining lugs reach into dashboard mountingCourtesy of PORSCHE OF NORTH AMERICA, INC.2.3. Push lock as far as possible to the left -arrow B- until retaining lugs -15- of lock reach into dashboardmounting -13- on left side. See Fig. 37, Fig. 38.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 38: View of retaining lugsCourtesy of PORSCHE OF NORTH AMERICA, INC.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 39: Screw in and tighten fastening screwCourtesy of PORSCHE OF NORTH AMERICA, INC.2.4. Screw in fastening screw -1- and tighten. See Fig. 39.3. Install glove compartment. --> 681519 Removing and installing glove compartment - "Installing"4. Install cover under dashboard on passenger's side. Refer to 70 22 19 Removing and installing cover underdashboard - as of MY 2003 (All Models) .5. Install trim strip for dashboard on passenger's side. Refer to 70 58 19 Removing and installing trim stripfor the dashboard on the passenger's side - as of MY 2003 (All Models) .Installing actuating cable for lockInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 40: Installation location of glove compartment lock1. Install actuating cable on lock.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 41: Inserting traction cable through holder of actuating cable on lockCourtesy of PORSCHE OF NORTH AMERICA, INC.1.1. Insert traction cable -6- through holder of actuating cable -13- on lock ( -arrow A- ). See Fig. 41.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 42: Inserting actuating cable on holder of lockCourtesy of PORSCHE OF NORTH AMERICA, INC.1.2. Insert actuating cable -3- on holder -13- of lock ( -arrow A- ). The fastening clips -4- of the tractionmounting must engage audibly into the lock holder. See Fig. 42.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 43: Attaching cable to actuating cable holderCourtesy of PORSCHE OF NORTH AMERICA, INC.1.3. Attach cable -6- to the assembly opening of actuating lever -7- from above -arrow B- and swivel to theactuating cable holder -13- on the lock ( -arrow C- ). See Fig. 43.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 44: Inserting traction cable through holder of actuating cable on lock boltCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Install actuating cable on lock bolt.2.1. Insert traction cable -6- through holder of actuating cable -14- on lock bolt ( -Arrow D- ). See Fig. 44.2.2. Insert actuating cable -3- on holder -14- of lock bolt ( -Arrow D- ). The fixing clips -10- of the tractionmounting must engage audibly into the lock bolt holder. See Fig. 44.2.3. Turn actuating lever -12- to the stop in direction of actuating cable holder -14- ( -Arrow E- ). See Fig. 44.2.4. Attach cable -6- to the assembly opening of actuating lever -12- from above and swivel to the actuatingcable holder -14- on the lock bolt ( -Arrow F- ). See Fig. 44.

--> The ignition key must not be withdrawn from the lock cylinder when removing the lock cylinder from or2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 45: Positioning cap on the lock bolt from above and press in till engagedCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Position cap -9- on the lock bolt -11- from above and press in. The fixing clips -9- of the cover must engageaudibly. See Fig. 45.4. Install glove compartment lock. --> 681119 Removing and installing glove compartment lock -"installing"5. Install glove compartment. --> 681519 Removing and installing glove compartment - "Installing"Installing lock cylinder for lockCAUTION: Danger of material damage in the event of incorrect removal andinstallation of lock cylinder.• In the event of incorrect removal and installation, the lock cylindercan be damaged.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior Equipmentinstalling it into the lock, as otherwise the spring-loaded locking elements will spring out of the lock barrel.--> If the ignition key is withdrawn with the lock cylinder removed, the locking elements must be held in onboth sides with the fingers until the ignition key is fully out of the lock cylinder. The locking elements can thenbe carefully relaxed and the lock cylinder laid down.--> Lock cylinders supplied as spare parts are secured in a transport case.Installation Location:Fig. 46: Installation location of glove compartment lock1. Remove transport case.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 47: Fully insert ignition key into new lock cylinderCourtesy of PORSCHE OF NORTH AMERICA, INC.1.1. Fully insert ignition key -4- into new lock cylinder -5- ( -Arrow A- ). See Fig. 47.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 48: Remove transport case from lock cylinderCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Remove transport case -9- from lock cylinder ( -Arrow B- ). See Fig. 48.Fig. 49: Installing lock cylinderCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Install lock cylinder.3.1. Turn actuating lever -7- to the horizontal installation position. See Fig. 49.4. Insert lock cylinder -5- together with ignition key -4- into the lock ( -arrow A- ). The release lug of the lockbarrel must be pointing to the left. See Fig. 49.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 50: Press lock cylinder into the lock until the retaining clips engageCourtesy of PORSCHE OF NORTH AMERICA, INC.5. Press lock cylinder -5- into the lock -2- until the retaining clips -6- of the lock cylinder audibly engage. SeeFig. 50.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 51: Remove ignition key from lock cylinderCourtesy of PORSCHE OF NORTH AMERICA, INC.6. Pull out ignition key -4- from lock cylinder -5- ( -Arrow B- ). See Fig. 51.7. Install cover.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 52: Position cover on the lock carrier and press in until the retaining clip engagesCourtesy of PORSCHE OF NORTH AMERICA, INC.7.1. Position cover -1- on the lock carrier -2- and press in -Arrow C- until the retaining clip audibly engages.See Fig. 52.8. Install actuating cable on lock. --> 681119 Removing and installing glove compartment lock -"installing"9. Install glove compartment lock. --> 681119 Removing and installing glove compartment lock -"installing"10. Install glove compartment. --> 681519 Removing and installing glove compartment - "installing"68 15 19 REMOVING AND INSTALLING GLOVE COMPARTMENT - AS OF MY2003 (ALL MODELS)PRELIMINARY WORKPreliminary work1. Remove trim strip for dashboard on passenger's side. Refer to 70 58 19 Removing and installing trim stripfor the dashboard on the passenger's side - as of MY 2003 (All Models) .2. Remove cover under dashboard on the passenger's side. Refer to 70 22 19 Removing and installing cover

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior Equipmentunder dashboard - as of MY 2003 (All Models) .REMOVING GLOVE COMPARTMENTRemoving glove compartmentInstallation Location:Fig. 53: Installation location of glove compartment1. Remove glove compartment.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 54: Removing glove compartment (1 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.1.1. Undo fastening screws -2- . See Fig. 54.1.2. Open glove compartment -1- , unscrew the fastening screws -4- and remove rubber buffer -3- . See Fig. 54.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 55: Removing glove compartment (2 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.1.3. Carefully pull out glove compartment -1- ( -arrow A- ) until the plug -5- can be removed. See Fig. 54, Fig.55.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 56: Removing glove compartment (3 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.1.4. Remove -5- plug -arrow C- , swivel out glove compartment -1- in a downward direction -arrow B- andremove it towards the rear -arrow A- . See Fig. 54.2. Disconnect plug and hose.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 57: Removing glove compartment (4 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.2.1. Release -6- and pull off -arrow D- connector. See Fig. 57.2.2. Pull off hose -7- for glove box air-conditioning system -arrow E- . See Fig. 57.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 58: Removing glove compartment (5 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.2.3. Unscrew fastening screws -9- on lock catch bolt -8- . See Fig. 58.2.4. Press in latch striker on lock catch bolt -8- -arrows F- and push it through to the rear -arrow G- . See Fig.58.2.5. Pull out glove compartment -1- to the rear -arrow H- . See Fig. 57.INSTALLING GLOVE COMPARTMENTInstalling glove compartmentInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 59: Installation location of glove compartment1. Connect plug and hose.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 60: Installing glove compartment (1 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.1.1. Insert glove compartment -1- -arrow A- . See Fig. 60.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 61: Installing glove compartment (2 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.1.2. Push through lock catch bolt -8- from the rear -arrow B- . See Fig. 61.1.3. Screw in fastening screws -9- on lock catch bolt -8- . See Fig. 61.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 62: Installing glove compartment (3 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.1.4. Push on the plug -6- until the locking tabs engage audibly -arrow D- . See Fig. 62.1.5. Push on hose -7- for glove box air-conditioning system -arrow C- . See Fig. 62.2. Install glove compartment.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 63: Installing glove compartment (4 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.2.1. Swivel in glove compartment -1- in a downward direction -arrow F- and push it in carefully -arrow G- ,until the plug -5- can be connected. See Fig. 63, Fig. 64.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 64: Installing glove compartment (5 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.2.2. Connect -5- plug -arrow E- , until the locking tabs engage audibly and then push in glove compartment -1-completely -arrow G- . See Fig. 64.2.3. Close glove compartment lid.2.4. Screw in fastening screws -2- in the sequence -2a to 2c- as shown and tighten to the specified tighteningtorque. --> Tightening torque: 1.4 (1.0 ftlb.) Nm +/-0.5 (0.5 ftlb.) Nm . See Fig. 63.2.5. Open glove compartment lid.2.6. Insert rubber buffer -3- and screw in fastening screws -4- in the sequence shown -4d to 4e- and tighten tothe specified tightening torque. --> Tightening torque: 1.4 (1.0 ftlb.) Nm +/-0.2 (0.2 ftlb.) Nm . See Fig. 63.2.7. Close glove compartment lid.2.9. Set gap for glove compartment lid by moving at the fastening points -2f and 2g- . See Fig. 63.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior Equipment2.10. Tighten fastening screws -2- in the sequence shown -2f and 2g- to the specified tightening torque. -->Tightening torque: 1.4 (1.0 ftlb.) Nm +/-0.2 (0.2 ftlb.) Nm . See Fig. 63.SUBSEQUENT WORKSubsequent work1. Install cover under dashboard on the passenger's side. Refer to 70 22 19 Removing and installing coverunder dashboard - as of MY 2003 (All Models) .2. Install trim strip for dashboard on passenger's side. Refer to 70 58 19 Removing and installing trim stripfor the dashboard on the passenger's side - as of MY 2003 (All Models) .68 17 19 REMOVING AND INSTALLING CENTER CONSOLE - AS OF MY2003 (ALL MODELS)PRELIMINARY WORKPreliminary work1. Remove cover for center console --> Removing center console cover.2. Only for vehicles with corresponding I number: remove control unit for auxiliary air conditioner. Refer to88 48 19 Removing and installing control unit for auxiliary air conditioner - as of MY 2003 (All Models) .3. Only for vehicles with corresponding I number: remove regulator for rear seat heating. Refer to 74 26 19Removing and installing regulator for rear seat heating - as of MY 2003 (All Models) .REMOVING CENTER CONSOLEInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 65: Installation location of center console

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 66: View of center consoleCourtesy of PORSCHE OF NORTH AMERICA, INC.Fig. 67: Removing covers and cupholderCourtesy of PORSCHE OF NORTH AMERICA, INC.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior Equipment1. Remove covers and cupholder.1.1. Unclip the covers -2, 4- from the center console. See Fig. 67.1.2. Open cupholder -3- . See Fig. 67.1.3. Push cupholder -3- upwards and unclip from the center console. See Fig. 67.2. Remove socket or cigarette lighter- only vehicles with the relevant I number.Fig. 68: Removing socket or cigarette lighterCourtesy of PORSCHE OF NORTH AMERICA, INC.2.1. Unscrew fastening screws -5- . See Fig. 68.2.2. Unclip and remove socket or cigarette lighter -4a- from the center console. See Fig. 68.2.3. Disconnect the plug connections.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 69: Removing socket or cigarette lighter connectorCourtesy of PORSCHE OF NORTH AMERICA, INC.2.4. Press in the plug locking tabs -6- ( -arrow A- ). See Fig. 69.2.5. Pull off plug -6- ( -arrow B- ). See Fig. 69.Installation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 70: Location of antennae for KESSY3. Disconnect plug connection.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 71: Disconnecting plug connector for antennae for KESSY (1 Of 3)Courtesy of PORSCHE OF NORTH AMERICA, INC.3.1. Unscrew fastening screw -14- . See Fig. 71.Fig. 72: Disconnecting plug connector for antennae for KESSY (2 Of 3)Courtesy of PORSCHE OF NORTH AMERICA, INC.3.2. Move the antennae for KESSY -12- slightly to the front and lift. See Fig. 72.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 73: Disconnecting plug connector for antennae for KESSY (3 Of 3)Courtesy of PORSCHE OF NORTH AMERICA, INC.3.3. Pull off plug connection -13- . See Fig. 73.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 74: Releasing center console at the frontCourtesy of PORSCHE OF NORTH AMERICA, INC.4. Release center console at the front.4.1. Unclip covers for grab handles -7- . See Fig. 74.4.2. Unscrew fastening screws -8- . See Fig. 74.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 75: Releasing center console at the centerCourtesy of PORSCHE OF NORTH AMERICA, INC.5. Release the center console in the center.5.1. Unscrew fastening screws -9- . See Fig. 75.6. Release the center console at rear.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 76: Releasing center console at the rear (1 Of 4)Courtesy of PORSCHE OF NORTH AMERICA, INC.6.1. Take out the mat -10- . See Fig. 76.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 77: Releasing center console at the rear (2 Of 4)Courtesy of PORSCHE OF NORTH AMERICA, INC.6.2. Unscrew fastening screws -11- . See Fig. 77.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 78: Releasing center console at the rear (3 Of 4)Courtesy of PORSCHE OF NORTH AMERICA, INC.7. Pull off plug.7.1. Release plug -15- ( -arrows C- ) and pull it off ( -arrow D- ). See Fig. 78.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 79: Releasing center console at the rear (4 Of 4)Courtesy of PORSCHE OF NORTH AMERICA, INC.8. Remove the center console --> See Fig. 79.INSTALLING CENTER CONSOLEInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 80: Installation location of center console

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 81: View of center consoleCourtesy of PORSCHE OF NORTH AMERICA, INC.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 82: Installing center console (1 Of 7)Courtesy of PORSCHE OF NORTH AMERICA, INC.1. Position the center console.1.1. Make sure that the rear air duct is plugged in correctly -arrow- . See Fig. 83.Fig. 83: Installing center console (2 Of 7)Courtesy of PORSCHE OF NORTH AMERICA, INC.2. Fasten the center console at rear.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 84: Installing center console (3 Of 7)Courtesy of PORSCHE OF NORTH AMERICA, INC.2.1. Screw in fastening screws -11- and tighten to the specified tightening torque. See Fig. 84.--> Tightening torque: 8 (6 ftlb.) Nm +0.8 (0.5 ftlb.) Nm

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 85: Installing center console (4 Of 7)Courtesy of PORSCHE OF NORTH AMERICA, INC.2.2. Insert the mat -10- . See Fig. 85.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 86: Installing center console (5 Of 7)Courtesy of PORSCHE OF NORTH AMERICA, INC.2.3. Push on the plug -15- until the locking tabs engage audibly. See Fig. 86.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 87: Installing center console (6 Of 7)Courtesy of PORSCHE OF NORTH AMERICA, INC.3. Fasten the center console in the center.3.1. Screw in fastening screws -9- and tighten to the specified tightening torque. --> Tightening torque: 6 ftlb.+0.5 ftlb. . See Fig. 87.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 88: Installing center console (7 Of 7)Courtesy of PORSCHE OF NORTH AMERICA, INC.4. Tighten the center console at the front.4.1. Screw in fastening screws -8- and tighten to the specified tightening torque. --> Tightening torque: 6 ftlb.+0.5 ftlb. . See Fig. 88.4.2. Clip in covers for grab handles -7- . See Fig. 88.Installation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 89: Location of antennae for KESSY

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 90: Installing antennae for KESSYCourtesy of PORSCHE OF NORTH AMERICA, INC.5. Make the plug connection.5.1. Connect plug connection -13- . See Fig. 90.5.2. Slide in the antennae for KESSY -12- towards the front and insert. See Fig. 90.5.3. Screw in fastening screw -14- and tighten. See Fig. 90.6. Only in vehicles with the relevant I number: install socket or cigarette lighter

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 91: Installing power socket or cigarette lighter (1 Of 2)Courtesy of PORSCHE OF NORTH AMERICA, INC.6.1. Connect plug -6- . See Fig. 91.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 92: Installing power socket or cigarette lighter (2 Of 2)Courtesy of PORSCHE OF NORTH AMERICA, INC.6.2. Clip the socket or cigarette lighter -4a- into the center console. See Fig. 92.6.3. Screw in fastening screws -5- and tighten to the specified tightening torque. --> Tightening: 2 (1.5 ftlb.)Nm +0.5 (0.5 ftlb.) Nm . See Fig. 92.

68 17 37 REMOVING AND INSTALLING RELEASE FOR ARMREST ON2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 93: Installing covers and cupholderCourtesy of PORSCHE OF NORTH AMERICA, INC.7. Install covers and cupholder.7.1. Clip covers -2, 4- and cupholder -3- into the center console. See Fig. 93.SUBSEQUENT WORKSubsequent work1. Only for vehicles with corresponding I number: install regulator for rear seat heating. Refer to 74 26 19Removing and installing regulator for rear seat heating - as of MY 2003 (All Models) .2. Only for vehicles with corresponding I number: install control unit for auxiliary air conditioner. Refer to88 48 19 Removing and installing control unit for auxiliary air conditioner - as of MY 2003 (All Models) .3. Install cover for center console --> Installing center console cover.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentCENTER CONSOLE - AS OF MY 2003 (ALL MODELS)REMOVING RELEASE FOR ARMREST ON CENTER CONSOLERemoving armrest releaseNOTE:If the lid cannot be opened, the lid release can be removed using a stop-gapmeasure. --> Emergency operation of releaseInstallation Location:In vehicles with phone handsets in the armrest, the entire armrest must bereplaced. --> 681737 Removing and installing armrest for center consoleFig. 94: Removing and installing armrest release

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 95: Opening coverCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Release and open cover and shelf on armrest.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 96: Unscrewing fastening screwsCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Pull off cap -2- and unscrew fastening screws -3- . See Fig. 96.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 97: Unclipping shelfCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Unclip shelf -4- and swivel it upwards. See Fig. 97.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 98: Removing releaseCourtesy of PORSCHE OF NORTH AMERICA, INC.4. Remove release.4.1. Press lower release button -arrow A- and pull release -1- upwards -arrow B- to remove it. See Fig. 98.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 99: Removing fastening nutsCourtesy of PORSCHE OF NORTH AMERICA, INC.5. Remove fastening nuts -5- . See Fig. 99.Emergency operation of release

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 100: Unscrewing fastening screwsCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Pull off caps -2- and unscrew fastening screws -3- . See Fig. 100.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 101: Unscrewing fastening screwsCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Unscrew fastening screws -6- . See Fig. 101.3. Unclip shelf.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 102: Unclipping shelfCourtesy of PORSCHE OF NORTH AMERICA, INC.3.1. Insert a screwdriver into armrest at the rear between the bottom half and the hinge -arrow C- and lever outthe rear clip connection -7- . See Fig. 102.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 103: Unclipping shelfCourtesy of PORSCHE OF NORTH AMERICA, INC.3.2. Insert an assembly wedge into armrest between the bottom half and the shelf tray -arrow D- and lever outthe front clip connection -7- . See Fig. 103.4. Remove bottom half.4.1. Operate release buttons -arrow E- . See Fig. 104.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 104: Removing bottom halfCourtesy of PORSCHE OF NORTH AMERICA, INC.Swivel bottom half out -arrow F- and remove -arrow G- . See Fig. 104.INSTALLING ARMREST RELEASEInstalling armrest releaseInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 105: Removing and installing armrest releaseNOTE:• Only on center consoles in which the release was removed using the stopgapmeasure.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 106: Installing bottom halfCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Place bottom half in position and screw in tightening screws -6- . --> Tightening torque: 8 (6 ftlb.) Nm .See Fig. 106.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 107: Screwing on fastening nutsCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Screw on fastening nuts -5- . See Fig. 107.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 108: Placing release in positionCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Place release in position.3.1. Press lower release button -arrow A- and push release -1- downwards -arrow B- . See Fig. 108.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 109: Clipping in shelfCourtesy of PORSCHE OF NORTH AMERICA, INC.4. Swivel shelf -4- downwards and clip it in. See Fig. 109.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 110: Screwing in fastening screwsCourtesy of PORSCHE OF NORTH AMERICA, INC.5. Screw in fastening screws -3- position caps -2- . --> Tightening torque: 2 (1.5 ftlb.) Nm . See Fig. 110.6. Press release buttons to check the release function.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 111: Closing coverCourtesy of PORSCHE OF NORTH AMERICA, INC.7. Close cover and shelf on armrest.68 17 37 REMOVING AND INSTALLING DAMPER FOR ARMREST ONCENTER CONSOLE - AS OF MY 2003 (ALL MODELS)PRELIMINARY WORKPreliminary work1. Remove control unit for auxiliary air conditioner. Refer to 88 48 19 Removing and installing control unitfor auxiliary air conditioner - as of MY 2003 (All Models) .2. Remove cup holder and socket --> 681719 Removing and installing center console - "Removing".3. Remove rear center console cover --> 681737 Removing and installing center console cover -"Removing".Removing damper for armrest on center consoleInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 112: Removing and installing damper for armrest on center consoleCourtesy of PORSCHE OF NORTH AMERICA, INC.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 113: Opening oddments trayCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Open oddments tray -Arrow A- . See Fig. 113.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 114: Unclipping safety clipCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Unclip safety clip -4- on both dampers -Arrow B- . See Fig. 114.NOTE:• Before unhooking the damper, secure the oddments tray and prevent itfrom closing.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 115: Unhooking dampersCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Unhook both dampers -3- ( -Arrow C- ). See Fig. 115.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 116: Unscrewing fastening screwsCourtesy of PORSCHE OF NORTH AMERICA, INC.4. Unscrew fastening screws -3- ( -Arrow A- ). See Fig. 116.5. Loosen and remove securing frame.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 117: Loosening securing frameCourtesy of PORSCHE OF NORTH AMERICA, INC.5.1. Insert a screwdriver between center console and securing frame and open up the center console -Arrow B- .Remove the locating pins on both sides of the securing frame from the bores on the center console -Arrow C- .See Fig. 117.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 118: Removing securing frameCourtesy of PORSCHE OF NORTH AMERICA, INC.5.2. Swivel securing frame upwards -Arrow D- and remove it -Arrow E- . See Fig. 118.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 119: Removing damperCourtesy of PORSCHE OF NORTH AMERICA, INC.6. Turn damper -1- ( -Arrow F- ), then unhook and remove it -Arrow G- . See Fig. 119.INSTALLING DAMPER FOR ARMREST ON CENTER CONSOLEInstalling damper for armrest on center consoleInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 120: Removing and installing damper for armrest on center consoleCourtesy of PORSCHE OF NORTH AMERICA, INC.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 121: Inserting damperCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Position damper -1- ( -Arrow G- ) and turn it so that it locks into position -Arrow F- . See Fig. 121.2. Position securing frame.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 122: Positioning securing frameCourtesy of PORSCHE OF NORTH AMERICA, INC.2.1. Position securing frame at the guide tabs -Arrow E- and swivel it downwards and into place -Arrow D- .See Fig. 122.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 123: Positioning securing frameCourtesy of PORSCHE OF NORTH AMERICA, INC.2.2. Insert the locating pins on both sides of the securing frame into the bores on the center console -Arrow C- .See Fig. 123.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 124: Screwing in fastening screwsCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Screw in fastening screws -3- and tighten to the specified tightening torque -Arrow A- . --> Tighteningtorque: 1.4 (1.0 ftlb.) Nm +/-0.5 (0.5 ftlb.) Nm . See Fig. 124.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 125: Opening oddments trayCourtesy of PORSCHE OF NORTH AMERICA, INC.4. Open oddments tray -Arrow A- . See Fig. 125.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 126: Hooking in dampersCourtesy of PORSCHE OF NORTH AMERICA, INC.5. Hook in both dampers -3- ( -Arrow C- ). See Fig. 126.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 127: Clipping in safety clipCourtesy of PORSCHE OF NORTH AMERICA, INC.6. Clip in safety clip -4- on both dampers -Arrow B- . See Fig. 127.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 128: Closing oddments trayCourtesy of PORSCHE OF NORTH AMERICA, INC.7. Close oddments tray -Arrow A- . See Fig. 128.SUBSEQUENT WORKSubsequent work1. Install rear center console cover --> 681737 Removing and installing center console cover - "Installing".2. Install control unit for auxiliary air conditioner. Refer to 88 48 19 Removing and installing control unit forauxiliary air conditioner - as of MY 2003 (All Models) .

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior Equipment3. Install cup holder and socket --> 681719 Removing and installing center console - "Installing".68 17 37 REMOVING AND INSTALLING REAR COVER FOR CENTERCONSOLE - AS OF MY 2003 (ALL MODELS)PRELIMINARY WORKPreliminary work1. Remove rear center air jet. Refer to 85 57 19 Removing and installing rear middle air vent - as of MY2003 (All Models) .REMOVING REAR COVER FOR CENTER CONSOLERemoving rear cover for center consoleInstallation Location:Fig. 129: Removing and installing rear cover for center consoleCourtesy of PORSCHE OF NORTH AMERICA, INC.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 130: Opening oddments trayCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Open oddments tray -Arrow A- . See Fig. 130.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 131: Unclipping cover for A/C control panelCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Unclip cover for air-conditioning control panel -2- ( -Arrow B- ). See Fig. 131.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 132: Screwing out screws at the topCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Screw out screws at the top -3- and remove them -Arrow C- . See Fig. 132.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 133: Loosening clip connection at the bottomCourtesy of PORSCHE OF NORTH AMERICA, INC.4. Loosen clip connection -4- at the bottom -Arrow D- . See Fig. 133.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 134: Removing coverCourtesy of PORSCHE OF NORTH AMERICA, INC.5. Remove cover -1- ( -Arrow E- ). See Fig. 134.INSTALLING REAR COVER FOR CENTER CONSOLEInstalling rear cover for center consoleInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 135: Removing and installing rear cover for center consoleCourtesy of PORSCHE OF NORTH AMERICA, INC.Fig. 136: Positioning cover

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior Equipment1. Position cover -Arrow E- . See Fig. 136.Fig. 137: Clipping in cover at the bottomCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Clip in cover at the bottom -Arrow D- . See Fig. 137.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 138: Screwing in screwsCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Insert and screw in screws at the top -3- ( -Arrow C- ) and tighten to the specified tightening torque. -->Tightening torque: 1.4 (1.0 ftlb.) Nm +/-0.5 (0.5 ftlb.) Nm . See Fig. 138.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 139: Clipping in cover for A/C control panelCourtesy of PORSCHE OF NORTH AMERICA, INC.4. Clip in cover for air-conditioning control panel -2- ( -Arrow B- ). See Fig. 139.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 140: Closing oddments trayCourtesy of PORSCHE OF NORTH AMERICA, INC.5. Close oddments tray -Arrow A- . See Fig. 140.SUBSEQUENT WORKSubsequent work1. Install rear center air jet. Refer to 85 57 19 Removing and installing rear middle air vent - as of MY 2003(All Models) .68 17 37 REMOVING AND INSTALLING PIN FOR ARMREST ON CENTERCONSOLE - AS OF MY 2003 (ALL MODELS)

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentPRELIMINARY WORKPreliminary work1. Remove rear cover for center console --> 681737 Removing and installing rear cover for center console -"Removing".REMOVING PIN FOR ARMREST ON CENTER CONSOLERemoving pin for armrest on center consoleInstallation Location:Fig. 141: Removing and installing pin for armrest on center consoleCourtesy of PORSCHE OF NORTH AMERICA, INC.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 142: Opening oddments trayCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Open oddments tray -Arrow A- . See Fig. 142.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 143: Unclipping safety clipCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Unclip safety clip -4- on both dampers -Arrow B- . See Fig. 143.NOTE:• Before unhooking the damper, secure the oddments tray and prevent itfrom closing.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 144: Unhooking dampersCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Unhook both dampers -3- ( -Arrow C- ). See Fig. 144.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 145: Unclipping safety clipCourtesy of PORSCHE OF NORTH AMERICA, INC.4. Unclip safety clip -2- on pin -Arrow D- . See Fig. 145.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 146: Removing pinCourtesy of PORSCHE OF NORTH AMERICA, INC.5. Remove pin -1- ( -Arrow E- ). See Fig. 146.INSTALLING PIN FOR ARMREST ON CENTER CONSOLEInstalling pin for armrest on center consoleInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Insert pin -1- ( -Arrow E- ). See Fig. 148.Fig. 149: Clipping on safety clipCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Clip safety clip -2- onto pin -Arrow D- . See Fig. 149.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 150: Hooking in dampersCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Hook in both dampers -3- ( -Arrow C- ). See Fig. 150.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 151: Clipping in safety clipCourtesy of PORSCHE OF NORTH AMERICA, INC.4. Clip in safety clip -4- on both dampers -Arrow B- . See Fig. 151.

68 17 37 REMOVING AND INSTALLING COVER FOR ODDMENTS TRAYLIGHT - AS OF MY 2003 (ALL MODELS)2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 152: Closing oddments trayCourtesy of PORSCHE OF NORTH AMERICA, INC.5. Close oddments tray -Arrow A- . See Fig. 152.SUBSEQUENT WORKSubsequent work1. Install rear cover for center console --> 681737 Removing and installing rear cover for center console -"Installing".

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentPRELIMINARY WORKPreliminary work1. Remove rear cover for center console --> 681737 Removing and installing rear cover for center console -"Removing".REMOVING COVER FOR ODDMENTS TRAY LIGHTRemoving cover for oddments tray lightInstallation Location:Fig. 153: Removing and installing cover for oddments tray lightCourtesy of PORSCHE OF NORTH AMERICA, INC.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 154: Releasing wire harnessCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Release wire harness -Arrow A- . See Fig. 154.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 155: Opening oddments trayCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Open oddments tray -Arrow B- . See Fig. 155.3. Unclip cover.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 156: Unclipping coverCourtesy of PORSCHE OF NORTH AMERICA, INC.3.1. Insert a screwdriver at the clip connections -2- and lever out the cover -Arrow C- . See Fig. 156.4. Remove cover.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 157: Removing coverCourtesy of PORSCHE OF NORTH AMERICA, INC.4.1. Remove cover -Arrow D- and release electric plug connection -3- ( -Arrow E- ). See Fig. 157.INSTALLING COVER FOR ODDMENTS TRAY LIGHTInstalling cover for oddments tray lightInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 158: Removing and installing cover for oddments tray lightCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Position cover.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 159: Positioning coverCourtesy of PORSCHE OF NORTH AMERICA, INC.1.1. Connect plug connection -Arrow E- and place cover in position -Arrow D- . See Fig. 159.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 160: Inserting tabsCourtesy of PORSCHE OF NORTH AMERICA, INC.1.2. Insert the tabs of the cover into the cut-outs in the trim panel -Arrows F- . See Fig. 160.2. Engage clips.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 161: Engaging clipsCourtesy of PORSCHE OF NORTH AMERICA, INC.2.1. Use a pointed-nose pliers to grip the locking tab and trim panel and press the locking tab into the clip -2- ( -Arrow C- ). See Fig. 161.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 162: Closing oddments trayCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Close oddments tray -Arrow B- . See Fig. 162.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 163: Laying wire harnessCourtesy of PORSCHE OF NORTH AMERICA, INC.4. Lay the wire harness -4- ( -Arrow A- ). See Fig. 163.SUBSEQUENT WORKSubsequent work1. Install rear cover for center console --> 681737 Removing and installing rear cover for center console -"Installing".68 17 37 REMOVING AND INSTALLING ARMREST FOR CENTER CONSOLE- AS OF MY 2003 (ALL MODELS)PRELIMINARY WORKPreliminary work1. Remove pin for armrest on center console --> 681737 Removing and installing pin for armrest on centerconsole - "Removing".REMOVING ARMREST FOR CENTER CONSOLERemoving armrest for center console

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentInstallation Location:Fig. 164: Removing and installing armrest for center consoleCourtesy of PORSCHE OF NORTH AMERICA, INC.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 165: Removing armrestCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Remove armrest.Fig. 166: Removing armrestCourtesy of PORSCHE OF NORTH AMERICA, INC.1.1. Tilt the pivot axis of the armrest -1- in the opposite direction to the pivot axis of the mount -2- ( -Arrow A-). See Fig. 166.1.2. Remove armrest to the side -Arrow B- . See Fig. 166.INSTALLING ARMREST FOR CENTER CONSOLEInstalling armrest for center consoleInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 167: Removing and installing armrest for center consoleCourtesy of PORSCHE OF NORTH AMERICA, INC.Fig. 168: Placing armrest in position

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Place armrest in position.Fig. 169: Placing armrest in positionCourtesy of PORSCHE OF NORTH AMERICA, INC.1.1. Tilt the pivot axis of the armrest -1- in the opposite direction to the pivot axis of the mount -2- and positionarmrest laterally on the mount -Arrow A- . See Fig. 168.1.2. Swivel armrest downward -Arrow B- . See Fig. 168.SUBSEQUENT WORKSubsequent work1. Install pin for armrest on center console --> 681737 Removing and installing pin for armrest on centerconsole - "Installing".68 17 37 REMOVING AND INSTALLING SWITCH FOR ODDMENTS TRAYLIGHT - AS OF MY 2003 (ALL MODELS)PRELIMINARY WORKPreliminary work

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior Equipment1. Remove damper for armrest on center console --> 681737 Removing and installing damper for armrest oncenter console - "Removing".REMOVING SWITCH FOR ODDMENTS TRAY LIGHTRemoving switch for oddments tray lightInstallation Location:Fig. 170: Removing and installing switch for oddments tray lightCourtesy of PORSCHE OF NORTH AMERICA, INC.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 171: Removing air ductCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Remove air duct.1.1. Unscrew fastening screws -2- ( -Arrow A- ). See Fig. 171.1.2. Remove air duct -3- ( -Arrow B- ). See Fig. 171.2. Remove switch.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 172: Loosening switchCourtesy of PORSCHE OF NORTH AMERICA, INC.2.1. Unhook locking tabs -Arrows C- and push switch -1- aside slightly -Arrow D- . See Fig. 172.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 173: Removing the switchCourtesy of PORSCHE OF NORTH AMERICA, INC.2.2. Press the button -5- from inside -Arrow E- and disengage the switch fully -Arrow F- . See Fig. 173.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 174: Disconnecting plug connectionCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Release plug connection -4- and remove switch -Arrow G- . See Fig. 174.INSTALLING SWITCH FOR ODDMENTS TRAY LIGHTInstalling switch for oddments tray lightInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 175: Removing and installing switch for oddments tray lightCourtesy of PORSCHE OF NORTH AMERICA, INC.Fig. 176: Connecting plug connection

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior Equipment1. Connect plug -4- and lock it -Arrow G- . See Fig. 176.2. Insert switch.Fig. 177: Positioning switchCourtesy of PORSCHE OF NORTH AMERICA, INC.2.1. Position switch -1- and press the button -5- towards the center console -Arrow F- . See Fig. 177.2.2. While keeping the button pressed, move the switch until the button -5- pops out through the trim panel -Arrow E- . See Fig. 178.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 178: Engaging switchCourtesy of PORSCHE OF NORTH AMERICA, INC.Engage switch -1- at the center console using the locking tabs. See Fig. 178.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 179: Checking that switch is engagedCourtesy of PORSCHE OF NORTH AMERICA, INC.2.3. Check that the switch is fully engaged -Arrow C- . See Fig. 179.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 180: Fitting air ductCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Fit air duct.3.1. Position air duct -3- ( -Arrow B- ). See Fig. 180.3.2. Screw in fastening screws -2- and tighten to the specified tightening torque -Arrow A- . --> Tighteningtorque: 2 (1.5 ftlb.) Nm +/-0.5 (0.5 ftlb.) Nm . See Fig. 180.SUBSEQUENT WORKSubsequent work

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior Equipment1. Install damper for armrest on center console --> 681737 Removing and installing damper for armrest oncenter console - "Installing".68 19 19 REMOVING AND INSTALLING COVER FOR CENTER CONSOLE -AS OF MY 2003 (ALL MODELS)REMOVING COVER FOR CENTER CONSOLEInstallation Location:Fig. 181: Installation location of center console coverCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Vehicles with manual transmission: remove shift lever knob. Refer to 34 04 19 Removing and installingshift lever knob - as of MY 2003 (Cayenne MAN, Cayenne S MAN) .

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 182: Removing cover for lock latchCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Remove cover for lock latch.2.1. Fold up middle armrest -2- . See Fig. 182.2.2. Unscrew fastening screws -3- . See Fig. 182.2.3. Remove cover for lock latch -4- . See Fig. 182.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 183: Removing cover for center console (1 Of 4)Courtesy of PORSCHE OF NORTH AMERICA, INC.3. Unclip cover for center console.3.1. Carefully fold up cover for center console -1- until the retaining lugs -A- can be pulled out from the guides.See Fig. 183, Fig. 185.3.2. Pull cover for center console -1- by the retaining lugs -A- from the guides. See Fig. 183, Fig. 185.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 184: Removing cover for center console (2 Of 4)Courtesy of PORSCHE OF NORTH AMERICA, INC.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 185: Removing cover for center console (3 Of 4)Courtesy of PORSCHE OF NORTH AMERICA, INC.4. Disconnect plug connection.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 186: Removing cover for center console (4 Of 4)Courtesy of PORSCHE OF NORTH AMERICA, INC.4.1. Press in the plug locking tabs -5- ( -arrow B- ). See Fig. 186.4.2. Pull off plug -5- ( -arrow C- ). See Fig. 186.5. Remove cover for center console.INSTALLING COVER FOR CENTER CONSOLEInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 187: Installation location of center console coverCourtesy of PORSCHE OF NORTH AMERICA, INC.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 188: Installing cover for center console (1 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.1. Push on the electrical plug connection.1.1. Connect plug -5- to the cover. See Fig. 188.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 189: Installing cover for center console (2 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.2. Position cover for center console.2.1. Hook the tabs -A- into the guides. See Fig. 190.2.2. Swivel the cover for the center console -1- downwards. See Fig. 191.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 190: Installing cover for center console (3 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 191: Installing cover for center console (4 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 192: Installing cover for center console (5 Of 5)Courtesy of PORSCHE OF NORTH AMERICA, INC.3. Install cover for lock latch.3.1. Position cover for lock latch -4- . See Fig. 192.3.2. Screw in fastening screws -3- and tighten to the specified torque. --> Tightening torque: 1.5 ftlb. +0.5ftlb. . See Fig. 192.3.3. Fold down middle armrest -2- . See Fig. 192.4. Vehicles with manual transmission: install shift lever knob. Refer to 34 04 19 Removing and installingshift lever knob - as of MY 2003 (Cayenne MAN, Cayenne S MAN) .68 20 19 REMOVING AND INSTALLING FRONT ASHTRAY - AS OF MY 2003(ALL MODELS)REMOVING FRONT ASHTRAY

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentRemoving front ashtrayInstallation Location:Fig. 193: Installation location of front ashtray1. Remove front air-conditioning system regulator. Refer to 87 02 19 Removing and installing front airconditioningsystem regulator - as of MY 2003 (All Models) .2. Open the front ashtray and remove the holder.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 194: Removing front ashtrayCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Remove front ashtray.3.1. Put the gear-shift lever in the -D- position.3.2. Undo fastening screws -2- . See Fig. 194.3.3. Pull the front ashtray -1- to the rear -Arrow A- , until the plug becomes accessible. See Fig. 194.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 195: Disconnect plug connectorCourtesy of PORSCHE OF NORTH AMERICA, INC.4. Pull off plug.4.1. Release -3- and pull off -Arrow B- plug. See Fig. 195.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 196: Pulling out ashtrayCourtesy of PORSCHE OF NORTH AMERICA, INC.5. Pull out ashtray -1- to the rear -arrow A- . See Fig. 196.INSTALLING FRONT ASHTRAYInstalling front ashtrayInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 197: Installation location of front ashtray

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 198: Inserting front ashtrayCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Insert front ashtray -1- ( -arrow A- ). See Fig. 198.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 199: Connecting plug connector (1 Of 2)Courtesy of PORSCHE OF NORTH AMERICA, INC.2. Connect connector.2.1. Push on the plug -3- until the locking tabs engage audibly -Arrow B- . When doing so, ensure that the plug-3- is positioned correctly in the mount -4- for the front ashtray -1- . See Fig. 199, Fig. 200.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 200: Connecting plug connector (2 Of 2)Courtesy of PORSCHE OF NORTH AMERICA, INC.3. Install front ashtray.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 201: Insert front ashtray into the guides and push it in completelyCourtesy of PORSCHE OF NORTH AMERICA, INC.3.1. Insert front ashtray -1- into the guides -5- and push it in completely -arrow A- . See Fig. 201.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 202: Installing front ashtray fastenersCourtesy of PORSCHE OF NORTH AMERICA, INC.3.2. Screw in -2- fastening screws. See Fig. 202.3.3. Put the gear-shift lever in the -P- position.68 23 19 REMOVING AND INSTALLING SUN VISOR - AS OF MY 2003 (ALLMODELS)REMOVING SUN VISORInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 203: Installation location of sun visor

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 204: Removing sun visor (1 Of 6)Courtesy of PORSCHE OF NORTH AMERICA, INC.1. Disengage adjustable part of the sun visor -1- from the mounting saddle and pivot towards roof frame ( -arrow A- ). See Fig. 204.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 205: Removing sun visor (2 Of 6)Courtesy of PORSCHE OF NORTH AMERICA, INC.2. Release mounting saddle.2.1. Unclip cover cap -2- on the mounting saddle -3- with a screwdriver and unfold ( -arrow B- ). See Fig. 205.2.2. Unscrew fastening screw -4- . See Fig. 205.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 206: Removing sun visor (3 Of 6)Courtesy of PORSCHE OF NORTH AMERICA, INC.3. Remove mounting saddle.3.1. Fold rear sun visor -5- downwards ( -arrow C- ). See Fig. 206.3.2. Carefully insert a screwdriver between roof lining and mounting saddle and unclip mounting saddle -3- ( -arrow D- ). See Fig. 206.3.3. Remove lock -6- from mounting saddle -3- ( -arrow F- ). See Fig. 206.3.4. Remove mounting saddle -3- in direction of arrow ( -arrow E- ). See Fig. 206.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 207: Removing sun visor (4 Of 6)Courtesy of PORSCHE OF NORTH AMERICA, INC.4. Release cover for pivot bearing:4.1. Pivot adjustable sun visor back into its normal position.4.2. Carefully insert a screwdriver between roof lining and pivot bearing -7- ( -arrow G- ) and release cover ( -arrow H- ). See Fig. 207.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 208: Removing sun visor (5 Of 6)Courtesy of PORSCHE OF NORTH AMERICA, INC.5. Remove pivot bearing.5.1. Unscrew fastening screws -8- . See Fig. 208.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 209: Removing sun visor (6 Of 6)Courtesy of PORSCHE OF NORTH AMERICA, INC.6. Remove sun visor and release electric plug connection.6.1. Unclip sun visor -9- and carefully lower it ( -arrow I- ), until the plug -11- is accessible. See Fig. 209.6.2. Release the locking tab -10- for the electrical plug connection ( -arrow K- ) and pull off the plug -11- ( -arrow L- ). See Fig. 209.6.3. Remove sun visor -9- . See Fig. 209.INSTALLING SUN VISORInstallation Location:

1.2. Insert plug for mirror light -11- ( -arrow B- ). See Fig. 211.2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 210: Installation location of sun visorFig. 211: Insert plug for sun visor mirror lightCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Install sun visor.1.1. Move sun visor -9- into installation position ( -arrow A- ). See Fig. 211.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior Equipment1.3. Clip in sun visor -9- completely ( -arrow A- ). See Fig. 211.Fig. 212: View of pivot bearing and fastenersCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Install pivot bearing.2.1. Screw in fastening screws -8- . See Fig. 212.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 213: Snap in pivot bearing coverCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Clip in cover for pivot bearing.3.1. Align and engage cover for pivot bearing -7- 4 ( -arrow C- ). See Fig. 213.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 214: Swivel adjustable part of the sun visor towards roof frameCourtesy of PORSCHE OF NORTH AMERICA, INC.4. Move adjustable sun visor to lateral position.4.1. Swivel adjustable part of the sun visor -1- towards roof frame ( -arrow D- ). See Fig. 214.4.2. Leave sun visor -5- in unfolded position. See Fig. 214.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 215: Installing mounting saddleCourtesy of PORSCHE OF NORTH AMERICA, INC.5. Install mounting saddle.5.1. Insert lock -6- in mounting saddle -3- ( -arrow E- ). See Fig. 215.5.2. Engage mounting saddle -3- at the top on the roof liner ( -arrow F- ). See Fig. 215.5.3. Swivel mounting saddle -3- forwards towards the windscreen and clip in place ( -arrow G- ). See Fig. 215.5.4. Pivot sun visor -5- towards roof liner (normal position) ( -arrow H- ). See Fig. 215.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 216: Fastening mounting saddleCourtesy of PORSCHE OF NORTH AMERICA, INC.6. Fasten mounting saddle.6.1. Unclip cover cap -2- on the mounting saddle -3- with a screwdriver ( -I- ) and unfold ( -arrow K- ). SeeFig. 216.6.2. Screw in fastening screw -4- and tighten. See Fig. 216.6.3. Close -2- cover cap -arrow L- . See Fig. 216.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 217: Swivel adjustable part of sun visor towards windscreenCourtesy of PORSCHE OF NORTH AMERICA, INC.7. Move swivelling sun visor to original position:7.1. Swivel adjustable part of the sun visor -1- towards windscreen ( -arrow M- ). See Fig. 217.68 27 19 REMOVING AND INSTALLING INTERIOR REAR-VIEW MIRROR - ASOF MY 2003 (ALL MODELS)REMOVING INTERIOR REAR-VIEW MIRRORRemoving interior rear-view mirror

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentInstallation Location:Fig. 218: Installation location of interior rear-view mirror

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 219: Removing left and right cover capsCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Remove left and right cover caps.1.1. Insert a plastic wedge between the cover caps -1- and carefully press apart. Remove cover caps. See Fig.219.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 220: Removing rear-view mirrorCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Remove rear-view mirror.2.1. Push rear-view mirror -2- in -direction of arrow- out of the mirror support. See Fig. 220.INSTALLING INTERIOR REAR-VIEW MIRRORInstalling interior rear-view mirrorInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 221: Installation location of interior rear-view mirror1. Install rear-view mirror.1.1. Push rear-view mirror -2- as far as the stop in -direction of arrow- onto the mirror support -3- . See Fig.222.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 222: Installing rear-view mirrorCourtesy of PORSCHE OF NORTH AMERICA, INC.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 223: Installing left and right cover capsCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Install left and right cover caps.2.1. Position the cover caps -1- on the rear-view mirror -2- and press together until the cover caps -1- engagefirmly on the left and right. See Fig. 223.68 35 19 REMOVING AND INSTALLING FRONT HANDLE - AS OF MY 2003(ALL MODELS)REMOVING FRONT HANDLERemoving front handleInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 224: Installation location of interior front handle

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 225: Unfold handleCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Unfold handle -1- . See Fig. 225.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 226: Remove fastener coverCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Unclip cover -2- . See Fig. 226.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 227: Removing fastening screwsCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Undo fastening screws -3- . See Fig. 227.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 228: Remove handle from roofCourtesy of PORSCHE OF NORTH AMERICA, INC.4. Remove handle -1- . See Fig. 228.INSTALLING FRONT HANDLEInstalling front handleInstallation Location:Fig. 229: Installation location of interior front handle

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 230: Installing handle to roofCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Position handle -1- . See Fig. 230.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 231: Screw in and tighten handle fastening screwsCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Screw in and tighten fastening screws -3- . --> Tightening torque: 3.5 ftlb. . See Fig. 231.Fig. 232: Install fastener coverCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Clip in cover -2- . See Fig. 232.NOTE:The handle must return itself to a normal position after it is released!

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 233: Fold up handleCourtesy of PORSCHE OF NORTH AMERICA, INC.4. Fold in handle -1- . See Fig. 233.68 37 19 REMOVING AND INSTALLING REAR HANDLE - AS OF MY 2003(ALL MODELS)REMOVING REAR HANDLEInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 234: Installation location of interior rear handle

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 235: Unfold grab handleCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Unfold grab handle -1- . See Fig. 235.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 236: View of grab handle fastener coverCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Unclip cover -2- . See Fig. 236.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 237: View of grab handle fastenerCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Undo fastening screws -3- . See Fig. 237.4. Remove grab handle -1- . See Fig. 238.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 238: Remove grab handleCourtesy of PORSCHE OF NORTH AMERICA, INC.INSTALLING REAR HANDLEInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 239: Installation location of interior rear handle

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 240: Installing grab handleCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Position grab handle -1- . See Fig. 240.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 241: Installing grab handle fastenersCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Screw in fastening screws -3- and tighten to the specified torque. --> Tightening torque: 3.5 ftlb. . See Fig.241.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 242: Installing fastener coverCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Clip in cover -2- . See Fig. 242.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 243: Fold in grab handleCourtesy of PORSCHE OF NORTH AMERICA, INC.4. Fold in grab handle -1- . See Fig. 243.4.1. Check whether the grab handle automatically folds back to the normal position after it is released.68 96 19 REMOVING AND INSTALLING SUN BLIND ON DOOR WINDOW -AS OF MY 2003 (ALL MODELS)REMOVING SUN BLIND AND HOLDER FOR SUN BLIND ON DOOR WINDOWRemoving sun blind and holder for door window sun blindInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 244: Installation location of door window sun blindCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Remove rear door trim panel. Refer to 70 73 19 Removing and installing rear door trim panel - as of MY2003 (All Models) .2. Remove cover.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 245: Unclip cover at top of door panelCourtesy of PORSCHE OF NORTH AMERICA, INC.2.1. Unclip cover -1- ( -Arrow A- ). See Fig. 245.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 246: Pulling sun blind out slightlyCourtesy of PORSCHE OF NORTH AMERICA, INC.2.2. Open up cover -1- ( -Arrows B- ) and remove above door window sun blind -2- ( -Arrow C- ) by pullingthe sun blind -2- out slightly. See Fig. 246.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 247: Removing door window sun blindCourtesy of PORSCHE OF NORTH AMERICA, INC.3. Remove door window sun blind.3.1. Undo fastening screws -3- . See Fig. 247.3.2. Remove door window sun blind -2- ( -Arrow D- ). See Fig. 247.Removing holder for door window sun blindInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 248: Installation location of door window sun blind holderCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Remove cover.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 249: Removing cover from holder for door window sun blindCourtesy of PORSCHE OF NORTH AMERICA, INC.1.1. Remove cover -2- from holder for door window sun blind -1- ( -Arrow A- ). See Fig. 249.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 250: Remove holder fastening screwCourtesy of PORSCHE OF NORTH AMERICA, INC.2. Remove holder for door window sun blind.2.1. Undo fastening screws -3- . See Fig. 250.2.2. Remove holder for door window sun blind -1- ( -Arrow B- ). See Fig. 250.INSTALLING SUN BLIND AND HOLDER FOR SUN BLIND ON DOOR WINDOWInstalling holder for door window sun blindInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 251: Installation location of door window sun blind holderCourtesy of PORSCHE OF NORTH AMERICA, INC.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 252: Inserting holder for door window sun blindCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Install holder for door window sun blind.1.1. Insert holder for door window sun blind -1- ( -Arrow A- ). See Fig. 252.1.2. Screw in -3- fastening screws. See Fig. 252.2. Push on cover.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 253: Push cover onto holder for door window sun blindCourtesy of PORSCHE OF NORTH AMERICA, INC.2.1. Push cover -2- onto holder for door window sun blind -1- ( -Arrow B- ). See Fig. 253.Installing door window sun blindInstallation Location:

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 254: Installation location of door window sun blindCourtesy of PORSCHE OF NORTH AMERICA, INC.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 255: Installing door window sun blindCourtesy of PORSCHE OF NORTH AMERICA, INC.1. Install door window sun blind.1.1. Position door window sun blind -2- ( -Arrow A- ). See Fig. 255.1.2. Screw in -3- fastening screws. See Fig. 255.2. Install cover.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 256: Pulling sun blind out slightlyCourtesy of PORSCHE OF NORTH AMERICA, INC.2.1. Open up cover -1- ( -Arrows B- ) and insert above the door window sun blind -2- ( -Arrow C- ) by pullingthe sun blind -2- out slightly. See Fig. 256.

2006 Porsche Cayenne2003-2008 ACCESSORIES & EQUIPMENT Interior EquipmentFig. 257: Install sun blind coverCourtesy of PORSCHE OF NORTH AMERICA, INC.2.2. Clip in cover -1- ( -Arrow D- ). See Fig. 257.3. Install rear door trim panel. Refer to 70 73 19 Removing and installing rear door trim panel - as of MY2003 (All Models) .