RFID Antenna Solutions - Mobile Mark

More documents

Recommendations

Info

US Office: Tel: 800-648-2800 or +1.847-671-6690UK Office: Tel: (+44) 1543 459555www.mobilemark.comCable Assemblies &Connectors• Custom RF cable assemblies built toorder• Variety of styles & connectors availableCustom CoaxCable Assemblies• Provides extension capability tostandard antennas configurations• Quality low lossMobile Mark manufactures custom cable assemblies. All standardcable assemblies/ connectors are 50 Ohm. Standard production leadtimes are typically 2 weeks. Longer lead times may apply to some.RG-174 (8216) is a very small (approx. 0.1”/2.5 mm) flexiblecable best suited for mobile/portable applications up to 1900 MHz. Itcan be used in short runs up to 2.7 GHz. For miniature sized connectorsit has the widest options available.LMR-100A is the low loss alternative for RG-174. It has the samesize diameter (0.1 inch or 2.5 mm) and can be used with the samerange of connectors. The cable is well shielded but is still flexible andeasy to handle.RG-58 (8240) is the work horse cable and is suitable for applicationsup to 2.7 GHz. It is best suited for cable runs under approximately20ft (6 meters).RF-195 (7806R) is the same size cable as RG-58, and uses thesame size connectors, with the added feature of lower cable losses.RF-195 would be suitable for cable runs over 15 ft (4.5 meters) or inhigh frequency applications up to 6 GHz. This is our standard cablefor applications above 2.5 GHz.LMR-195FR is a non-halogen (non-toxic), low smoke, fire retardantcable. It has the same diameter as RF-195, can be fitted with the samevariety of connectors, and has the same cable loss.LMR-240 is a lower loss cable than RF-195 and best suited forlonger cable runs from 20 ft - 50 ft (6 meters - 15 meters) as well asfor higher frequency applications up to 6 GHz or more.LMR-400 is suitable for long runs & higher frequency applications.Approximately 0.405” diameter (10 mm), it might be too large forsome mobile installs, but is perfect for every base station transmitteror access point. Longer lead times may apply.LMR-600 is the lowest loss cable we offer. It is a premium low losscable. It is suitable for base station installations where the antennamay be mounted on a tower with long runs of cable.Cable Type Loss Per ft. at Loss Per ft. at Loss Per ft. at Loss Per ft. at900 MHz 2000 MHz 2500 MHz 5000 MHzRG-174 0.32 dB 0.49 dB 0.55 dB NRLMR-100A 0.22 dB 0.30 dB 0.39 dB 0.50 dBRG-58 0.14 dB 0.21 dB 0.24 dB 0.43 dBRF-195 0.10 dB 0.15 dB 0.17 dB 0.25 dBLMR-195FR 0.10 dB 0.15 dB 0.17 dB 0.25 dBLMR-240 0.07 dB 0.10 dB 0.12 dB 0.17 dBLMR-400 0.04 dB 0.06 dB 0.07 dB 0.12 dBLMR-600
US Office: Tel: 800-648-2800 or +1.847-671-6690UK Office: Tel: (+44) 1543 459555www.mobilemark.comCable StripperSurge ArrestorHole Saw(drill bit)Ground Plane KitInstallation & ProtectionOptions• Installation hardware: Crimp tools,adapters & cable weathersealing• RF Coax Surge Protector products frompopular manufacturersCrimp ToolsConnector SealingTapeMastic SealingKits• Proven name brand/OEM productsConnectorAdaptersCrimp Dies• Easy, one-stop shopping for antennas &accessories.In addition to our world class line of antenna products, Mobile Markcan supply a variety of accessories to ease installation and provideprotection features. We offer several OEM and name brand products.Lightning/Surge ArrestorsWe offer several name brand surge arrestor products. Surge arrestorsare important to protect your entire radio system. Surge arrestorstypically won’t save the antenna in a direct lightning strike, they areintended to protect more expensive equipment down stream. TheSurge Arrestors are generally configured by operating frequency.Special Vehicle Install HelpersMany of the popular antennas require a 3/4” hole for mounting. Toeasily make a hole, utilize a 3/4 hole saw on a drill bit to make a quickand clean installation. Some antennas require a ground plane, aslisted in the spec sheets. We offer a ground plane disc for antennasthat are mounted to a plastic or fiberglass surface. The ground planedisc is available in several hole sizes.Crimp Tools & Cable StrippersFor attaching or replacing your own cable connectors, a ratchet crimptool is offered. The standard crimp tool accepts various hex dies. Thedies needed depend on the type/size of cable you are using. We offerthe dies for our most popular cable types. A quick spinning cablestripper is an almost effortless way to properly prepare cable forcrimping a connector. They are designed to prep cable more preciselythan using a hand strip tool.Cable/Connector SealingIf you are using a product outdoors, it is always a good idea to useone of the mastic kits designed to seal up connector/cable junctions.Even if the connector is used in a seemingly protected environment,condensation can cause moisture to buildup in connectors. Overtime, that moisture can move into cable and reduce the performancesignificantly.RF Connector AdaptersSometimes a quick change is needed for an existing antenna or cableto interface with a different connector. RF adapters provide a quickway of changing the connecting style to exactly what you need. RFadapters have negligible signal losses, so there is nothing better for aquick solution. Also, data applications may require special adapters6to interface to an external antenna. We also offer a variety of jumpercable adapters to suit your needs.ModelDescriptionLightning& Surge ArrestorsACC-GT-NFF-ALGas Tube Surge Arrestor, 0-7 GHz, N Jack(Female-Female)ACC-TW-LP-005N Lightning Arrestor 0 - 6 GHz, N Bulkhead(Female-Female)ACC-AL-LSXMSurge Protector 2 - 6 GHz, N Jack(Female-Female)Special Vehicle Install HelpACC-HSK193/4” Hole saw/drill bitACC-K332Ground plane disc, 6” DVarious Hole Sizes AvailableCrimp Tools & Cable StrippersACC-RFA-4005-20 Crimper Hand set (no die)ACC-RFA-4005-01 Crimper Die for RG-58/RF-195ACC-RFA-4005-09 Crimper Die for RG-174/LMR-100ACC-RFA-4005-14 Crimper Die for LMR-400ACC-1258Cable Stripper RG-174/LMR-100ACC-HTA-312BCable Stripper for RG-58/RF-195ACC-15035WSCable stripper for RG-8/LMR-400Cable/Connector SealingACC-22281 in x10 ft Fusion Sealing tape (roll)ACC-RVS-11Roll-on mid cable Seal (Rayvolve)ACC-FT3430Fusion Bond tape 3/4” x 30 ft rollACC-WK-UUniversal Weatherproofing KitConnector Adapters770-000-0-010 TNC Jack to SMA Plug Adapter770-000-0-012 TNC Jack to Rev Polarity TNC Plug770-000-0-009 TNC Jack to N Plug Adapter770-000-0-008 SMA Jack to N Plug Adapter 0-7 GHz770-000-0-011 SMA Jack to N Plug Adapter 0-4 GHzSome models may only be available from the USA.Contact your sales representative for a full list of adapters.Specifications subject to Change without notice (6/2013)
Page 1 and 2: Francin, le 16 mars 2012La saison r
Page 8 and 9: US Office: Tel: 800-648-2800 or +1.
Page 12: US Office: Tel: 800-648-2800 or +1.

RFID Antenna Solutions - Mobile Mark

Create successful ePaper yourself

Delete template?

Save as template?