RFID Antenna Solutions - Mobile Mark

US Office: Tel: 800-648-2800 or +1.847-671-6690UK Office: Tel: (+44) 1543 459555www.mobilemark.comMounting Accessories &Options• Universal Wall Mounts available instandoffs of 2.5 inches to 1 ft. (6 - 30 cm)Universal WallMount 2.5”StandoffUniversal WallMount 4”StandoffUniversal WallMount 12”Standoff• Truck mirror and trunk lid mountsavailable for Stud mount antennas• Wall/Pole mount adapts stud antennasto fixed base station/access point• L bracket simplifies mounting of ODSeries antennas to a wallTruck MirrorMount for StudAntennasPole Mount forStud AntennasTrunk LidMount StudAntennasWall Mountfor OD SeriesAntennaUniversal Base Station Wall MountsThese universal wall mounts can be used with any model antennathat provides pole mounting hardware. Each kit comes with 2 wallmount brackets and a unifying 2” OD pole (51 mm). Standoffs areavailable for 2.5”, 4” and 12” distances. The 12” stand off versionsupplies an additional support leg for proper strength.Pole Mount Adapter KitThe model RM-MK wall and pole mount can be used to adapt a studmount antennas for used as a fixed access point. The kit can accommodateantennas with stud diameter up to 3/4” and is supplied witha 2.75” ground plate.Universal MountThe NT-MK L-bracket mount can be used for a number of differentmodels, including many of the site antennas.Truck Mirror MountThe Truck Mirror Mount (Model SM-MM) can be used to adapt mostof Mobile Mark’s Stud mount antennas for truck side mirror mounting.The ground plate is 2 3/4” diameter (70 mm) aluminum and themounting hole can accommodate up to 3/4” stud (19 mm).Trunk Lid Mount AdapterThe model SM-TM provides vehicle trunk (or hood) lid mounting forour stud mount antennas. The SM-TM provide mounting U shapedtangs (with set screws), that wrap around the trunk surface/weatherstrip.The ground plate is 2 3/4” round (70 mm), and can accommodatea stud size of up to 3/4” (19 mm).Wall Mount - OD SeriesThe model OD-WMK is a simplified L shaped bracket to mount theOD Series antennas to a wall. The aluminum bracket provides a 5”standoff from the wall, and is supplied with U Bolts for accommodatingthe 1” diameter (25 mm) of the OD body.Replacement kitsReplacement kits are often requested to make it easier to move an7antenna from one installation to another. In particular, the re-installtape kit for the MM3 glass mount antennas facilitates re-installation.Note: Some mounting accessories & kits may only be availabe fromthe USA.Model #DescriptionUniversal Base Station Wall MountsACC-83052.5” stand off (6 cm) wall mount with poleACC-1026434” stand off (10 cm) wall mount with poleACC-10302412” stand off (30 cm) wall mount with poleWall MountPN-WMKNLM-WMAdjustable wall mount for panelsWall mount for NLM SeriesWall/Pole Mount AdapterRM-MKWall & Pole adapter kit for stud mnt. antennasBP-MKPole/Wall mount for BP SeriesUniversal Pole Mount/Wall MountNT-MKL-bracket mountMobile MountSM-TMSM-MMOmni Series MountsOD-WMKOD-MKPipe MountNLM-PMYAG-PMKReplacement KitMM-KPN-MKVehicle Trunk lid mount with ground plateTruck Mirror mount, with ground plateL Bracket for wall mounting OD Series antennasStandard Pole mount; Fits mast up to 2.5” ODPole mount for NLM SeriesPole mount for YAGI antennasMM3 Re-install tape kitReplacement mount for PS SeriesSpecifications subject to Change without notice (6/2013)