Tsunami MP.11 Installation and Management Guide Model 5012 ...

More documents

Recommendations

Info

Configuration Tsunami MP.11 5012/5054-SUI Installation and ManagementSystem Parameters• Source MAC 6 bytes• Ethernet Type 2 bytesIf the average packet size is 1000 bytes, the overhead saved is 1.5%; With a frame size of 64 bytes, the overhead savedis 20%; and for frame sizes of 128 bytes, the saving is 10%. Network researches claim that most network traffic consistsof frames smaller than 100 bytes.In order to support routers behind the SUs with multiple subnets and prevent routing loops, you want individual routes(and more then one) per SU.Routing Mode ExamplesIn the first example, both the BSU and the SUs are configured for Routing mode. This example is appropriate forbusinesses connecting remote offices that have different networks.In example 2, the BSU is in Routing mode and the SUs are in Bridge mode. Notice the PCs behind the SUs mustconfigure their default gateways to point to the BSU, not the SU.Notes:• One of the most important details to pay attention to in Routing mode are the unit’s and the PC’s default gateways. Itis a common mistake to set up the PC’s gateway to point to the SU when the SU is in Bridge mode and the BSU is inRouting mode. Always check to make sure the PCs on your network are configured to send their IP traffic to thecorrect default gateway.• Be sure to reboot the unit to permanently save static routes. New routes take effect immediately without a reboot, butare not permanently saved with your configuration until you do reboot the device. An unexpected power outage couldcause static routes you entered to “disappear” when the unit reboots if they have not been saved. You also shouldsave a copy of your unit’s configuration file in case the unit must be reloaded. This saves you from being required tore-enter numerous static routes in a large network.• The routing table supports up to 500 static routes.62
Configuration Tsunami MP.11 5012/5054-SUI Installation and ManagementNetwork ParametersNetwork ParametersThe Network tab contains the following sub-tabs. Note that the availability of some sub-tabs depends on whether the unitis in Bridge or Routing Mode.• IP Configuration• Roaming• DHCP Server• Spanning Tree (Bridge Mode Only)• IP Routes (Routing Mode only)• DHCP Relay Agent (Routing Mode Only)IP ConfigurationClick Configure > Network > IP Configuration to view and configure local IP address information. Configurable settingsdiffer between Bridge mode and Routing mode.Bridge ModeIf the device is configured in Bridge mode, the following screen is displayed:Configure or view the following parameters:• IP Address Assignment Type:– Select Static if you want to assign a static IP address to the unit. Use this setting if you do not have a DHCPserver or if you want to manually configure the IP settings– Select Dynamic to have the device run in DHCP client mode, which gets an IP address automatically from aDHCP server over the network.When the unit is in Bridge mode, only one IP address is required. This IP address also can be changed with ScanTool(see Setting the IP Address with ScanTool).IP Address: The unit’s static IP address (default IP address is 10.0.0.1). This parameter is configurable only if the IPAddress Assignment Type is set to Static.63
Page 1 and 2:
Tsunami MP.11 Installation and Mana
Page 4:
Tsunami MP.11 5012/5054-SUI Install
Page 8 and 9:
Page 10 and 11:
Introduction Tsunami MP.11 5012/505
Page 12 and 13: Introduction Tsunami MP.11 5012/505
Page 14 and 15: Tsunami MP.11 5012/5054-SUI Install
Page 16 and 17: Installation and Initialization Tsu
Page 30 and 31: System Overview Tsunami MP.11 5012/
Page 50 and 51: Basic Management Tsunami MP.11 5012
Page 58 and 59: System Status Tsunami MP.11 5012/50
Page 60 and 61: Configuration Tsunami MP.11 5012/50
Page 108 and 109: Monitoring Tsunami MP.11 5012/5054-
Page 110 and 111: Monitoring Tsunami MP.11 5012/5054-
Page 112 and 113:
Monitoring Tsunami MP.11 5012/5054-
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Commands Tsunami MP.11 5012/5054-SU
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Procedures Tsunami MP.11 5012/5054-
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Troubleshooting Tsunami MP.11 5012/
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Country Codes and Channels Tsunami
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Technical Services and Support Tsun
Page 160 and 161:
show all

Tsunami MP.11 Installation and Management Guide Model 5012 ...

Create successful ePaper yourself

Delete template?

Save as template?