MAX-FLO MICRO - Smartpartspaintball.co.uk

More documents

Recommendations

Info

MAX-FLO MICRO WARNINGS– Only use the Max-Flo Micro with a gas cylinder that has been tested and certified as compliant to DOT (USDepartment of Transportation,) HSE, PI (Europe) standards. Do not use the Max-Flo Micro with a gascylinder for which the certification has expired – most DOT exemptions must be renewed by certifiedhydrotesting and inspection every 3 or 5 years.– Only use suitable fill stations that are fitted with industry standard connectors. Inspect all connectorsprior to filling for signs of wear, abuse, suitability, dirt or debris. Filling is only to be carried out bycompetent, trained personnel. All persons in the immediate fill area must wear suitable eye protection andremain clear of vented gasses. Do not fill the Max-Flo Micro system beyond the operational pressure ratingof the cylinder to which it is attached. Never fill the Max-Flo Micro system to pressure above 4,500 psi.– Fast filling of cylinders results in heating of the gas and cylinder. If filled too fast, this heat can becomeexcessive which may cause damage to the cylinder. Such damage can lead to failure of the cylinder,causing potential property damage and personal injury. Care must be taken so that the cylindertemperature does not exceed 130 degrees F (55 degrees C).– Prior to each filling, the cylinder must be examined for signs of damage, including heat/flame exposure.If any damage is observed, do not fill the cylinder. Take the suspect cylinder to a DOT or HSE authorizedhydrostatic tester for inspection and pressure testing.– The cylinder can fly off with enough force to injure or kill if the cylinder is unscrewed while pressurized.Improper use, filing, storage or disposal may result in property damage, serious injury, or death. Thecylinder must only be filled by properly trained personnel. Do not expose to temperatures exceeding 130degrees F (55degrees C), when pressurized. Do not modify the cylinder in any way, or place any stickers onthe cylinder.– In accordance with the United States Transportation Security Agency, the Max Flo Micro regulator must beremoved from the cylinder prior to transport in checked luggage on commercial passenger aircraft.– This precaution list and operator’s manual must always accompany the product in the event of resale ornew ownership. The latest version of this manual is available for free download at www.SmartParts.com.– SHOULD YOU BE UNSURE AT ANY STAGE, YOU MUST SEEK EXPERT ADVICE.©2005 SMART PARTS, INC. SMART PARTS®, CROSSHAIR® LOGO, EQUIPMENT COUNTS® AND MAX-FLO MICRO ARE TRADEMARKS OR REGISTERED TRADEMARKS OWNED BY SMART PARTS, INC.MAX-FLO MICRO IS COVERED BY PATENTS: 5,755,213; 5,957,119. ADDITIONAL PATENTS PENDING.800.922.2147 www.smartparts.com02
GETTING FAMILIARIMPORTANTThe Max-Flo Micro preset compressed air system provides the stabilityand high flow rates that have made the Max-Flo line of regulators thechoice of champions, combined with an easy to use pre-set configuration.A combination of increased air-flow rates, decreased weight and lowermaintenance makes the Max-Flo Micro an ideal choice.– Complies with airline travel regulations– User-friendly, rebuildable, inline on/off– Preset to 800 psi (standard) or 450 psi (low-output model) output pressure.– Includes Smart Parts S-rail (compatible with industry standard 1/2” air system rails)FIG. 1MAX-FLO MICROThis manual is for a 3000psi or 4500psi system. Please refer to the sticker on theunderside of the regulator. A 3000psi regulator should only be used with a 3000psirated tank, and a 4500psi regulator should only be used with a 4500psi rated tank.Always release all pressure from your air tank by disconnecting the macroline hosebetween the regulator and the gun, and turning the on/off valve to on to release thepressure before removing the cylinder.Always wear correct eye protection when working on any high pressure system.The cylinder can fly off with enough force to kill if the cylinder is unscrewedwhile pressurized. Improper use, filing, storage or disposal may result in propertydamage, serious injury, or death. The cylinder must only be filled by properly trainedpersonnel. Do not expose to temperatures exceeding 130 degrees F (55 degrees C),when pressurized. Do not modify the cylinder in any way, or place any stickers onthe cylinder.©2005 SMART PARTS, INC. SMART PARTS®, CROSSHAIR® LOGO, EQUIPMENT COUNTS® AND MAX-FLO MICRO ARE TRADEMARKS OR REGISTERED TRADEMARKS OWNED BY SMART PARTS, INC.MAX-FLO MICRO IS COVERED BY PATENTS: 5,755,213; 5,957,119. ADDITIONAL PATENTS PENDING.800.922.2147 www.smartparts.com03
Page 1 and 2: MAX-FLO MICRO1Operation and Adjustm
Page 3: MAX-FLO MICRO WARNINGS- Never use o
Page 7 and 8: MAX-FLO MICRO PARTSEXPLODED DIAGRAM
Page 9 and 10: DISASSEMBLYPLEASE READ CAREFULLY04T
Page 11 and 12: TROUBLESHOOTINGAIR LEAKS FROM THE F

MAX-FLO MICRO - Smartpartspaintball.co.uk

Create successful ePaper yourself

Delete template?

Save as template?