HP Series Operating Manual - Jands

More documents

Recommendations

Info

RUN: SNAP 1~3, SCENE 1&2, PRE-RECORDED CHASES 1~6[Exit to DMX operation] [Exit to DMX operation] [Exit to DMX operation]NORMALNORMALNORMALSTATUS[over all Level of SNAP]STATUS[over all Level of SCENE]STATUS[Speed in B.P.M.]SELECTSELECTSELECT[Stand alone channel level][4] [4] [4][Stand alone channel level][Stand alone channel level]STATUSSTATUSSTATUS[Speed]SELECTSELECTSELECT[SP1: SNAP1 / SP2: SNAP2 / SP3: SNAP 3]ENTER[1] [2] [3]ENTERENTER[SC1: SCENE1 / SC2: SCENE2][PR1 -PR6: Prerecorded chases][1] DISPLAY = "SP1 on level 100""SP2 on level 100""SP3 on level 100"[2] DISPLAY = "SC1 on level 100""SC2 on level 100"[3] DISPLAY = "PR1 run 100 B.P.M.""PR2 run 100 B.P.M.""PR3 run 100 B.P.M.""PR4 run 100 B.P.M.""PR5 run 100 B.P.M.""PR6 run 100 B.P.M."RUN[START]RUN[4] Press SELECT and hold whileadjusting channel level via levelcontrol.This step removes the selectedchannel from a SNAP, SCENE orPRE-RECORDED CHASE andenables the channel level to beadjusted in isolation. These newlevels are not stored.Figure 4.4Status LED red = 110VStatus LED green = 240VHP DIMMER MS-9507-04
Dimmer Operation 4-74.1.7.2 SceneE Figure 4.3Once a Scene (“SC1” or “SC2”) is selected, the display will scroll the message:“PRESS SELECT AND HOLD WHILE CHANGE LEVEL FOR EACHCHAN”.• For each channel required to Build the Scene, press and hold the SELECTbutton.• The display will initially show the last recorded level for that channel, whichmay then be changed by rotating the LEVEL/FUNCTION encoder wheel.• Once all the required channels have been changed, press ENTER to confirmthe changes.• The display will change to “OK” to indicate the dimmer is now in normaloperating mode.4.1.8 RUN menuE Figure 4.4The HP12-TR / HP12-SC dimmers offer a range of pre-recorded Snapshots, Scenesand Chases that may be used for testing purposes or for when the dimmer rack isused in stand-alone (no control desk) applications.The Snapshots and Scenes must be recorded via the Build menu (see section 4.1.7).The Chase patterns are factory-set and cannot be changed. The output levels ofSnapshots and Scenes may be varied with the LEVEL/FUNCTION encoder wheel,which becomes a master level control. During chases the encoder wheel becomes achase rate control.In all cases, individual channel levels may be changed. Once changed, however, theyremain at the new level regardless of the setting of the master level control.Note that any previously disabled channels will remain disabled when in RUNmode, with chase sequences abbreviated to avoid visible gaps.• To run a Snapshot, Scene or Chase, press the RUN keypad button.• Select either a Snapshot (“SP1”, “SP2”, or “SP3”), a Scene (“SC1” or“SC2”), or a Factory Preset Chase (“PR1”, “PR2”, “PR3”, “PR4”, “PR5”,or “PR6”) with the FUNCTION encoder wheel.• Press ENTER to confirm the selection.4.1.8.1 SnapshotE Figure 4.4If Snapshot 2 (“SP2”) is selected, the display will scroll with the message “SP2ON LEVEL 100”.• The output level may be altered with the LEVEL/FUNCTION encoderwheel and the display will indicate a level between 100% and 0%.• Pressing a channel SELECT button will isolate that channel from the masterlevel control. The STATUS LED will flash to show the channel is isolated.Pressing the SELECT button again will re-connect the channel to the masterlevel control.Revision 2 - 20 March, 1997 HP SERIES DIMMER OPERATING MANUAL
Page 1 and 2: HP SeriesDigitally Controlled Dimme
Page 3 and 4: ContentsiiTable of ContentsTable of
Page 5 and 6: Contentsiv8.0 Technical Data and Sp
Page 7 and 8: Introduction 1-01.0 IntroductionThe
Page 9 and 10: BLANKPAGE
Page 11 and 12: Equipment Description 2-02.0 Equipm
Page 13 and 14: Getting Started 3-03.0 Getting Star
Page 15 and 16: Getting Started 3-23.4 Power-up seq
Page 17 and 18: Dimmer Operation 4-04.0 Dimmer Oper
Page 19 and 20: Dimmer Operation 4-24.1.4.3 “LAW
Page 21 and 22: Dimmer Operation 4-34.1.4.5 “P. F
Page 23 and 24: BLANKPAGE
Page 25 and 26: Dimmer Operation 4-5with dimmer law
Page 27: Dimmer Operation 4-64.1.6 DMX BANK
Page 31 and 32: Dimmer Operation 4-9rate control on
Page 33 and 34: Fault Diagnosis 5-05.0 Fault Diagno
Page 35 and 36: Fault Diagnosis 5-2reactivate the l
Page 37 and 38: Fault Diagnosis 5-45.8 Fault findin
Page 39 and 40: Installation 6-06.0 InstallationFor
Page 41 and 42: Installation 6-26.1.3 Rack Mounting
Page 43 and 44: Installation 6-46.2.2 Wall Mounting
Page 49 and 50: Installation 6-106.4 Wall Mounting
Page 51 and 52: Maintenance 7-07.0 MaintenanceWARNI
Page 53 and 54: Tecnnical Data and Specifications 8
Page 61: BLANKPAGE

HP Series Operating Manual - Jands

Create successful ePaper yourself

Delete template?

Save as template?