end-of-sale and end-of-life announcement for low density ... - CXtec

More documents

Recommendations

Info

Milestone Definition DateEnd of Service ContractRenewal DateLast Date of SupportThe last date to extend or renew a service contract for the product. The extensionor renewal period cannot extend beyond the last date of support.The last date to receive service and support for the product. After this date, allsupport services for the product are unavailable, and the product becomesobsolete.May 14, 2010August 14, 2010Table 2.Product Part Numbers Affected by This AnnouncementEnd-of-Sale Product Part NumberNM-1VNM-2VVIC-2FXSVIC-2FXOVIC-2FXO-EUVIC-2FXO-M1VIC-2FXO-M2VIC-2FXO-M3VIC-2E/MVIC-2BRI-S/T-TEVIC-2BRI-NT/TEVIC-2CAMAProduct DescriptionOne voice/fax interface card slot network moduleTwo voice/fax interface card slot network moduleTwo-port Foreign Exchange Station (FXS) voice/fax interface cardTwo-port Foreign Exchange Office (FXO) voice/fax interface cardTwo-port FXO voice/fax interface card (for Europe)Two-port FXO voice/fax interface card with battery reversal detection and caller ID support(for US, Canada and others)Two-port FXO voice/fax interface card with battery reversal detection and caller ID support (for Europe)Two-port FXO voice/fax interface card (for Australia)Two-port ear and mouth (E&M) voice/fax interface cardTwo-port Basic Rate Interface (BRI) voice/fax interface card (terminal side)Two-port BRI voice/fax interface card (network and terminal side)Two-port Centralized Automated Message Accounting (CAMA) trunk interface card The VIC-2 direct inward dial (DID) card is not affected by this end-of-sale and end-of-life announcement.PRODUCT MIGRATION OPTIONSThe recommended replacements for the Cisco low density voice/fax network modules (NM-1V and NM-2V) and associated VICs are the Cisco IPCommunications Voice/Fax Network Modules (NM-HD-xx) and associated VICs. Table 3 provides relevant information for migrating from the NMxVfamily of modules to the NM-HD-xx family of modules.The Cisco IP Communications Voice/Fax Network Modules (NM-HD-1V, NM-HD-2V and NM-HD-2VE) support all the features of the current lowdensity voice/fax network modules (NM-xV) while offering significant advantages such as higher port and channel densities and a new generation ofDSPs with greater memory and processing power. The Cisco IP Communications Voice/Fax Network Modules employ the same modulararchitecture as low density voice/fax network modules, and the new family of configurable voice interface cards supports all the existing voice/faxinterface types.© 2005 Cisco Systems, Inc. All rights reserved.Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com.Page 2 of 5
The Cisco IP Communications Voice/Fax Network Modules (and associated VICs) are supported on Cisco 2600XM Series products, and Cisco2691, 3640/A, and 3660 multiservice access routers, and Cisco 3725 and 3745 multiservice access routers starting with Cisco IOS® Softwarereleases 12.2(15)ZJ, 12.3(4)T, and 12.4M. These network modules and VICs are supported on Cisco 2800 and 3800 Integrated Services Routersstarting with Cisco IOS Software releases 12.3(8)T4 and 12.3(11)T, respectively. (Note: Cisco 2801 Integrated Services Router supports only theVICs since it does not contain a network module slot.) These VICs are also supported on Cisco 1751 and 1760 modular access routers platforms inCisco IOS Software Release 12.3(4)T and mainline 12.3(5) or later releases.Additional information about the IP Communications Voice/Fax Network Modules can be found at:http://www.cisco.com/en/US/products/hw/modules/ps5365/products_data_sheet0900aecd801c595e.htmlTable 3.Product ComparisonsCisco EOL Product Cisco Replacement Product CommentsNM-1V NM-HD-1V Twice the channel density of the NM-1V Supports up to 4 FXS, 4 FXO, 2 DID,2 E&M, or 2 BRI portsNM-2V NM-HD-2V Twice the channel density of the NM-2V Supports up to 8 FXS, 8 FXO, 4 DID,4 E&M, or 4 BRI ports (or a mix)VIC-2FXS VIC2-2FXS or VIC-4FXS/DID Can choose a 2-port or a 4-port VIC. The DID feature of VIC-4FXS/DIDcurrently is supported only on the Cisco 1751 and 1760 modular access routersVIC-2FXO VIC2-2FXO or VIC2-4FXO Can choose a 2-port or a 4-port VIC. The new VIC2-xFXO are universal cardsfor all countriesVIC-2FXO-EU VIC2-2FXO or VIC2-4FXO Can choose a 2-port or a 4-port VICVIC-2FXO-M1 VIC2-2FXO or VIC2-4FXO Can choose a 2-port or a 4-port VICVIC-2FXO-M2 VIC2-2FXO or VIC2-4FXO Can choose a 2-port or a 4-port VICVIC-2FXO-M3 VIC2-2FXO or VIC2-4FXO Can choose a 2-port or a 4-port VICVIC-2CAMA VIC2-2FXO or VIC2-4FXO FXO cards include the CAMA optionVIC-2E/M VIC2-2E/M Same density as the VIC-2E/MVIC-2BRI-S/T-TE VIC2-2BRI-NT/TE Supports terminal and network sideVIC-2BRI-NT/TE VIC2-2BRI-NT/TE Supports terminal and network side The NM-HD-xx network modules also support the VIC-2DID.Customers can use the Cisco Technology Migration Plan (TMP) to trade in products and receive credit toward the purchase of new Cisco equipment.For more information about Cisco TMP, go to: http://www.cisco.com/go/tradein/. The Cisco TMP application requires all users to have a Cisco.comuser ID.Customers may be able to continue to purchase Cisco low density voice/fax network modules (NM-1V and NM-2V) and associated VICs throughCisco’s Authorized Refurbished Equipment program. Refurbished units of these network modules and VICs are available in limited supply for sale© 2005 Cisco Systems, Inc. All rights reserved.Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com.Page 3 of 5
Page 1: PRODUCT BULLETIN NO. 2769END-OF-SAL
Page 5: © 2005 Cisco Systems, Inc. All rig

end-of-sale and end-of-life announcement for low density ... - CXtec

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?