Automatic Lubrication System - Andantex USA Inc.

More documents

Recommendations

Info

MODULAR RACK & PINION SYSTEMTechnical InformationSpecial grease for linear guideways & ball screwsgrease Herion F03With H1 approvalgrease Herion F02LUBRICANTS- short-fibred and homogeneous lithium-saponified universalgrease with one mineral oil. It can be used for roller and slidebearing lubrication and is appropriate for medium and highload applications.- very adhesive; appropriate for short-stroke applications.- water resistant and protective against corrosion.Applications:- lubrication of linear bearings (recirculating ball bearing guides,roller guides and ballscrews)- in combination with a lubrication pinion and continuousrelubrication suitable for open gear lubrication- Easily pumped by relubrication unitstemperature range -20°C to +120°C- synthetic special grease for high temperatures based on synthetichydrocarbons with a partial special thickener of high metal affinity.- possesses the NSF/H1-registration, the continuation of the formerUSDA/H1-approval of lubricants which are allowed for foodcontact.quality attributes:- water (cold, hot) and steam resistant- high thermal and oxidation stability- for high load; very good wear-protection- high service life and wide temperature range- optimum lubricating effect at low friction valuestemperature range -40° C to +140° C800-713-6170 • www.andantex.com • info@andantex.com16
MODULAR RACK & PINION SYSTEMSPLITTERS FOR RELUBRICATION UNIT FlexxPumpPart No. Inlets Outlets Grease (g) Qty. of Lubricant TypeOil (o)per piston stroke134-005-002 1 2 g ~0.08 cc Splitter 1 inlet, 2 outlets, grease134-005-003 1 3 g 0.05 cc Splitter 1 inlet, 3 outlets, grease134-005-004 1 4 g ~0.04 cc Splitter 1 inlet, 4 outlets, grease134-005-006 1 2 o ~0.08 cc Splitter 1 inlet, 2 outlets, oil134-005-007 1 3 o 0.05 cc Splitter 1 inlet, 3 outlets, oil134-005-008 1 4 o ~0.04 cc Splitter 1 inlet, 4 outlets, oilEach outlet of the FlexxPump can be combined with only one splitter. The combination of 2 or more splitters at one pumpoutlet is not possible. Therefore, the maximum lubrication points that can be serviced by one FlexxPump 404DLS and4 splitters is 16.INSTALLATION RECOMMENDATIONS:The splitters are designed to connect to 6 mm outside diameter tubes. The splitters should be located as close as possible tothe FlexxPump outlets.The length of the tubes between the outlet side of the splitter and the lubrication points should be as close as possible toequal. Pressure differences between the outlets should not exceed 3 bars (43.5 PSI). The amount of lubricant supplied tolubrication points can vary slightly depending on the pressure differences at the outlets.17800-713-6170 • www.andantex.com • info@andantex.com
Page 1 and 2: Flexxpump AutomaticRelubrication Sy
Page 3 and 4: MODULAR RACK & PINION SYSTEMFLEXXPU
Page 9 and 10: MODULAR RACK & PINION SYSTEMLUBRICA
Page 11 and 12: MODULAR RACK & PINION SYSTEMLUBRICA
Page 13 and 14: MODULAR RACK & PINION SYSTEMMOUNTIN
Page 15: MODULAR RACK & PINION SYSTEMLUBRICA
Page 19 and 20: MODULAR RACK & PINION SYSTEMTUBES F

Automatic Lubrication System - Andantex USA Inc.

Create successful ePaper yourself

Delete template?

Save as template?