OD-570 / OD-580 - GELEC (HK)

OD-570/OD-580 Series OD-570/OD-580 Series OD-570/OD-580 SeriesOD-570/OD-580 SeriesPanel Introduction:1Versatile InterfaceAt 60 MHz, 150MHz or 250MHz bandwidthwith Color or Mono LCD display, aredesigned and built to meet the demands ofa modern DSO in the main stream markettoday. The unmatched performance , valuedplus features, user-friendly design andversatile interface make OD-570/OD-580series a very useful equipment for most ofthe applications in circuit design , productiontest, repair service and education lab. Withalmost everything you could expect from aDSO, OD-570/OD-580 series provides youwith the best solution for waveform measurementat a surprisingly affordable price.1. Miscellaneous2. Power Switch3. Trigger Function4. Horizontal System5. Vertical System6. Function Keys7. Menu ON/OFF8. Cal. System9. Vertical Input10. External Input2345USB Interface for Video OutputThe OD-570/580 series offer different types of communicationinterfaces: RS-232C, USB, Centronics and GPIB, as well asGo-No Go signal generation. The USB port FreeView communicationsoftware is provided for viewing quasi-synchronouswaveform on both, the instrument display and PC screen. AlsoFreeCapture software is available for bi-directional datatransference and commands via RS-232C or GPIB interface tothe Personal Computer.1.5 MbpsUSB 2.0Waveform real-time Monitoring via USB InterfaceWaveform Captured via RS-232C or GPIBInterfaceIdeal for presentations usingpanoramic screens or videoprojector125.000 PointsAcquisition Memorycan be Transferred toa Personal ComputerFeatures60 MHz, 150 MHz and 250 MHz BandwidthColor or Monochrome LCD Display25GS/s Sampling Rate for Repetitive Waveforms125k Long Memory and 12 Division HorizontalDisplay15 Auto Measurements and simultaneous ∆T/ ∆VCursors25 GS/s ET Sampling Rate and 125 k Memory6 7 89 1015 Auto Measurements and simultaneously ∆T/ ∆V Cursors FFT FunctionGPIBPrinter PortRS-232CUSBGo / No Go OutputAuto Set-Up SequenceFrequency Adjustable ProbeCalibration SignalThe probe calibration signal is frequency adjustablefrom 1 kHz to 100 kHz with 1 kHz per step, andduty cycle adjustable from 5% to 95% with 5% perstep. This probe calibration signal is providedmainly for the accurate adjustment of probecompensation, but is also adequate to be used asa signal source for teaching and basic testing.(This function is only available for OD-576/OD-856)FFT FunctionZoom IN/OUTAdvanced Trigger: Pulse Width, TV Line, EventDelay and Time DelayAdjustable Probe Compensation SignalAdjustable Frequency Range: 1 kHz~100 kHzAdjustable Duty Cycle: 5%~ 95%RS-232C SignalDistorted RS-232C SignalWith Short MemoryRS-232C Signal With LongMemoryOD-570/OD-580 Series, with its superior sampling rate up to 25GS/s , provides high resolutionof 40ps point to point for repetitive waveform display. With 125k long memory,OD-570/OD-580 series gives higher or equal sampling rate and longer record length for thetransient signal under test. In general, the longer memory a DSO has the higher sampling rateit performs under the same time base setting. This is among the reasons that OD-570/OD-580 series could always give a better waveform display than the DSO that only has shortmemory.Display 10 Auto-MeasurementData at One ShotUsing Vertical and HorizontalCursors SimultaneouslyThe 15 Auto Measurement functions of OD-570/OD-580 series enables you to getthe most frequently tested parameters easily. OD-570/OD-580 series is able todisplay 10 auto measurement data on the screen for two channels at one shot. At aglance, you get all your measurement results immediately.FFT Function for AM SignalWith FFT function, OD-570/OD-580 series could easily transform the signaldisplay from time domain into frequency domain. Most remarkably,OD-570/OD-580 series is able to display a signal by the forms of both timedomain and frequency domain at the same time. The cursors under FFTmode are used to indicate the ∆ values of frequency and voltage, and therelative values of ∆ frequency and voltage of the signal components. Allthese measurement readings could be shown on the screen simultaneously.Auto Set-Up SequenceAuto Set-Up Sequence enables the testing engineers to carry out ATE testwithout software programming. After programmed with a sequence of frontpanel Set-Ups, OD-570/OD-580 series starts to perform the measurementsstep by step according to the sequence of front panel Set-Ups until it completesthe whole cycle of ATE test. The ATE test cycle on OD-570/OD-580series could be programmed to repeat continually by a number of times asyou wish.Frequency at 1 kHz, Duty Cycle at 50%Frequency adjustable probe calibration signal(only OD-576/OD-586)12 Division Horizontal DisplayAdvanced Trigger FunctionsGo/NoGo ModeOn-Screen Help MenuGo/NoGo and Auto Setup Sequence*Built-In Help Manual, PC Software andMulti-LanguageFrequency at 1 kHz, Duty Cycle at 30%(for OD-576/OD-586 only)Interfaces*- USB- RS-232C- Printer Centronics Port- GPIB(*) According to model, refer to specifications table10 Division Horizontal Display 12 Division Horizontal DisplayThe on-screen menu of a DSO gives the convenience of operation, but it also limits thescreen space of waveform display. OD-570/OD-580 series offers you with the alternative toview the waveform with 12 divisions when the on-screen menu is not in use. At a press of abutton, the screen is available for 12- division waveform display. Press the button again, youhave the display get back to normal. It is a very useful feature when you expect to view alonger portion of the signal under test.Pulse Width TriggerOD-570/OD-580 series provides advanced trigger features such as TV linetrigger, pulse width trigger, event delay trigger and time delay trigger, whichcould only be found in a higher-end DSO. The advanced trigger capability ofOD-570/OD-580 series makes the waveform capture in a broad range ofapplications possible.Go/NoGo TestingUtilizing the saved waveforms in Ref A and Ref B memories of OD-570/OD-580 series, the user could easily create the template to monitor theabnormal signal or event and perform the Go/NoGo test on the DSO. Forconvenience, the template could also be generated by the % deviation fromthe displayed waveform. Whenever the abnormal signal violates the pre-setNoGo condition, OD-570/OD-580 is capable of calculating the failure rate,taking the appropriate action of warning, and sending the status signal ofNoGo through rear panel."Real-Time" On- Screen Help MenuOn-Screen Help Menu allows you to get the real-time help whenever youneed to know the details of the function of any operation key. Press the "Help"key first, then press any other function key on the front panel, you will get theOn-Screen Help Menu for that specific function key you just pressed.Frequency at 1 kHz, Duty Cycle at 80 %(for OD-576/OD-586 only)