Series 200 control system - Vinten Radamec

More documents

Recommendations

Info

Critical data Input Voltage 110 VAC, 60 Hz or 230 VAC, 50 Hz Input Current 9 Amps total nominal at 110 VAC. 5 Amps total nominal at 230 VAC 11
Technical support If you are based in North, South or Central America and need technical support on the AutoCam system, contact Vinten Inc. at: 709 Executive Blvd. Valley Cottage, NY 10989 USA Phone:1-888 4 VINTEN (1-888-484-6836) - Toll free in the U.S.A. +1 845-268-0100 Fax:+1 845-268-0113 Or, if you are based outside of North, South or Central America, contact Vinten Broadcast Limited at: Western Way Bury St. Edmunds Suffolk IP33 3TB ENGLAND Phone: +44 (0) 1284 752121 Fax: +44 (0) 1284 750560 12
Page 1 and 2: Series 200 Control System Operating
Page 3 and 4: Foreword This manual provides Safet
Page 5 and 6: Contents (Cont) Page Remote operati
Page 7 and 8: Safety - read this first! Warning s
Page 9 and 10: Safe operating zone and pedestal fo
Page 11: Software WARNING!:DO NOT install an
Page 15 and 16: Manual outline Safety - read covers
Page 17 and 18: Series 200 control system The AutoC
Page 19 and 20: The AutoCam philosophy The underlyi
Page 21 and 22: Chapter 2 - Operation 20
Page 23 and 24: ENABLE Press the yellow ENABLE butt
Page 25 and 26: At the console Starting the system
Page 27 and 28: The Main screen There are only a fe
Page 29 and 30: File management This section covers
Page 31 and 32: NEW NEW is used to generate a new s
Page 33 and 34: SAVE SAVE appears only after a show
Page 35 and 36: Gray A gray background indicates th
Page 37 and 38: Pan relative steering Pan relative
Page 39 and 40: Fig 2.10 Targeting (1) 3. After loa
Page 41 and 42: Fig 2.12 Targeting (3) 9. After the
Page 43 and 44: Creating shots To create a shot: 1.
Page 45 and 46: Stopping a move To stop a move at a
Page 47 and 48: Learning a motion 1. Touch NEW and
Page 49 and 50: Your new motion called ~CCC now app
Page 51 and 52: 3. Try selecting a shot and going t
Page 53 and 54: 2. Touch MOTEDIT (for MOTion EDIT).
Page 55 and 56: The Edit menu The Edit menu is used
Page 57 and 58: MOTEDIT/REPLACE This button is cont
Page 59 and 60: Chapter 3 - Configuration 58
Page 61 and 62: . Fig 3.1 Main screen 60
Page 63 and 64:
Selecting the target locations The
Page 65 and 66:
Fig 3.3 Measuring the target positi
Page 67 and 68:
QUICK JUMP/MOVE OFF Quick Jump and
Page 69 and 70:
FOCUS NORMAL This is a toggle funct
Page 71 and 72:
3. Toggle PAN NORMAL/REVERSE etc to
Page 73 and 74:
Chapter 4 - Maintenance and Repair
Page 75 and 76:
telephone service is available 24 h
Page 77 and 78:
Gross failure of the interface boar
Page 79:
M Main screen 25, 26, 60 Manual out
show all

Series 200 control system - Vinten Radamec

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?