Series 200 control system - Vinten Radamec

More documents

Recommendations

Info

Introduction This chapter covers hands-on familiarization with remote control of the cameras, introduces the touchscreens, file management and describes remote camera control. This chapter also describes how to create and edit shots and motions. The control panel The joystick control panel provides operator control of the camera selected on the touchscreen. Control is provided for head pan, tilt and height, pedestal height and position, and lens zoom and focus. The Time lever sets the duration of a Move from one shot to another. Fig 2.1 The control panel 21
ENABLE Press the yellow ENABLE button to activate the control panel. The button is lit when on. NOTE: The status of control panel switches is displayed on the on-screen panel status bar (see page 26). Left-hand joystick and controls HEIGHT Twist the left joystick clockwise or counterclockwise to raise or lower the column. The sense of the height knob (whether clockwise = up or down) is set in the Configuration Screen (see page 65) or by using the Z- HOLD REV button. DRIVE/STEER Push the joystick in any direction to move the pedestal. There are two options available - conventional and pan relative steering, selected during Configuration (see page 65). 1. With conventional steering the direction of movement is relative to the absolute zero of the target. 2. With pan relative steering, when driven forwards the pedestal will travel in the direction the camera is pointing Speed is proportional to joystick displacement. The sense of the drive/steer action (whether push left = drive/steer left or right) is set in the Configuration Screen (see later in this chapter) or by using the X- HOLD REV or Y-HOLD REV buttons. FOCUS Turn the Focus knob to focus the lens. The sense of the FOCUS knob (whether forward = focus far or focus near) is set in the Configuration Screen (see page 65) or by using the FOCUS HOLD REV button. HOLD REV buttons HOLD REV buttons are provided for X, Y, Z and FOCUS. These have a dual operation. When pressed and released, the button will be lit and that function will be disabled. Press and hold reverses the sense of the joystick and the appropriate REV lamp below the joystick will be lit. Press the HOLD REV button again to cancel the action. 22
Page 1 and 2: Series 200 Control System Operating
Page 3 and 4: Foreword This manual provides Safet
Page 5 and 6: Contents (Cont) Page Remote operati
Page 7 and 8: Safety - read this first! Warning s
Page 9 and 10: Safe operating zone and pedestal fo
Page 11 and 12: Software WARNING!:DO NOT install an
Page 13 and 14: Technical support If you are based
Page 15 and 16: Manual outline Safety - read covers
Page 17 and 18: Series 200 control system The AutoC
Page 19 and 20: The AutoCam philosophy The underlyi
Page 21: Chapter 2 - Operation 20
Page 25 and 26: At the console Starting the system
Page 27 and 28: The Main screen There are only a fe
Page 29 and 30: File management This section covers
Page 31 and 32: NEW NEW is used to generate a new s
Page 33 and 34: SAVE SAVE appears only after a show
Page 35 and 36: Gray A gray background indicates th
Page 37 and 38: Pan relative steering Pan relative
Page 39 and 40: Fig 2.10 Targeting (1) 3. After loa
Page 41 and 42: Fig 2.12 Targeting (3) 9. After the
Page 43 and 44: Creating shots To create a shot: 1.
Page 45 and 46: Stopping a move To stop a move at a
Page 47 and 48: Learning a motion 1. Touch NEW and
Page 49 and 50: Your new motion called ~CCC now app
Page 51 and 52: 3. Try selecting a shot and going t
Page 53 and 54: 2. Touch MOTEDIT (for MOTion EDIT).
Page 55 and 56: The Edit menu The Edit menu is used
Page 57 and 58: MOTEDIT/REPLACE This button is cont
Page 59 and 60: Chapter 3 - Configuration 58
Page 61 and 62: . Fig 3.1 Main screen 60
Page 63 and 64: Selecting the target locations The
Page 65 and 66: Fig 3.3 Measuring the target positi
Page 67 and 68: QUICK JUMP/MOVE OFF Quick Jump and
Page 69 and 70: FOCUS NORMAL This is a toggle funct
Page 71 and 72: 3. Toggle PAN NORMAL/REVERSE etc to
Page 73 and 74:
Chapter 4 - Maintenance and Repair
Page 75 and 76:
telephone service is available 24 h
Page 77 and 78:
Gross failure of the interface boar
Page 79:
M Main screen 25, 26, 60 Manual out
show all

Series 200 control system - Vinten Radamec

Create successful ePaper yourself

Delete template?

Save as template?