Series 200 control system - Vinten Radamec

More documents

Recommendations

Info

Shot background colors The colors used on the screen have specific meanings, and make it easy to operate the <strong>system</strong>. They show in a consistent way which shot the camera has framed, the shot’s status, and which shot is next. The background colors are gray, green, red, light blue, dark blue, yellow and purple. NOTE: Fig 2.8 is for illustrative purposes only - in normal operation the shot colors would not all be shown at the same time Fig 2.8 Shot background colors 33
Gray A gray background indicates that the shot, which does not involve a pedestal move, is available - AAA in Fig 2.8. Green A green background is used to indicate that the next shot has been selected - BBB in Fig 2.8. A shot with a green background will be the next shot framed when you touch JUMP or MOVE. Green is the “where you are going” color for shots. Red When the camera is moving to the shot, the background goes to red. The page number at the bottom of the column, or in the centre in expand mode, turns red while any camera on that page is moving. Dark blue A dark blue background indicates that the camera is at that particular shot, untrimmed, exactly as stored. In Fig 2.8, CAM 1 is at DDD. Blue is the “where you are” color. Yellow A yellow background indicates that a pedestal move is involved in going to that shot - ~EEE in Fig 2.8. Light blue Light blue as a background is used to indicate a trimmed shot. For instance, in normal operation, FFF might be incorrectly framed because the talent has shifted position since the shot was originally learned. Typically, you will trim the shot before it is taken to air, or even on air if necessary. As soon as you adjust any of the axes, the background switches to light blue indicating that the current shot is no longer identical to the stored shot. For example, if you were to pan slightly from FFF on Camera 1, its background would change to light blue and a blue REPLACE key would appear at the bottom of the screen. If you want to resave this trimmed shot under the old name, touch REPLACE and resave the shot. A typical use of this function would be re-centering shots before a show, to correct for minor variations in talent’s position. Purple A purple background indicates the previous shot. In Fig 2.8 the camera was at GGG before it moved to DDD. Purple is the “where you where” color. 34
Page 1 and 2: Series 200 Control System Operating
Page 3 and 4: Foreword This manual provides Safet
Page 5 and 6: Contents (Cont) Page Remote operati
Page 7 and 8: Safety - read this first! Warning s
Page 9 and 10: Safe operating zone and pedestal fo
Page 11 and 12: Software WARNING!:DO NOT install an
Page 13 and 14: Technical support If you are based
Page 15 and 16: Manual outline Safety - read covers
Page 17 and 18: Series 200 control system The AutoC
Page 19 and 20: The AutoCam philosophy The underlyi
Page 21 and 22: Chapter 2 - Operation 20
Page 23 and 24: ENABLE Press the yellow ENABLE butt
Page 25 and 26: At the console Starting the system
Page 27 and 28: The Main screen There are only a fe
Page 29 and 30: File management This section covers
Page 31 and 32: NEW NEW is used to generate a new s
Page 33: SAVE SAVE appears only after a show
Page 37 and 38: Pan relative steering Pan relative
Page 39 and 40: Fig 2.10 Targeting (1) 3. After loa
Page 41 and 42: Fig 2.12 Targeting (3) 9. After the
Page 43 and 44: Creating shots To create a shot: 1.
Page 45 and 46: Stopping a move To stop a move at a
Page 47 and 48: Learning a motion 1. Touch NEW and
Page 49 and 50: Your new motion called ~CCC now app
Page 51 and 52: 3. Try selecting a shot and going t
Page 53 and 54: 2. Touch MOTEDIT (for MOTion EDIT).
Page 55 and 56: The Edit menu The Edit menu is used
Page 57 and 58: MOTEDIT/REPLACE This button is cont
Page 59 and 60: Chapter 3 - Configuration 58
Page 61 and 62: . Fig 3.1 Main screen 60
Page 63 and 64: Selecting the target locations The
Page 65 and 66: Fig 3.3 Measuring the target positi
Page 67 and 68: QUICK JUMP/MOVE OFF Quick Jump and
Page 69 and 70: FOCUS NORMAL This is a toggle funct
Page 71 and 72: 3. Toggle PAN NORMAL/REVERSE etc to
Page 73 and 74: Chapter 4 - Maintenance and Repair
Page 75 and 76: telephone service is available 24 h
Page 77 and 78: Gross failure of the interface boar
Page 79: M Main screen 25, 26, 60 Manual out

Series 200 control system - Vinten Radamec

Create successful ePaper yourself

Delete template?

Save as template?