Kingsman Marquis Solace Manual - Brock White

More documents

Recommendations

Info

MQHBZDV4736 - Framing for your Gas FireplaceFraming Specifications1. Cold climate installation recommendation: When installing this fireplaceagainst non insulated exterior wall or chase, it is recom mendedthat the outer walls be insulated to conform to applicable insulationcodes. Drywall must be installed over insulation to prevent contact ofinsulation and unit.2. Choose fireplace location and frame in accordance with the fireplaceframing dimensions specified (See Framing Diagrams). Bend nailingtabs forward on left and right of unit and place fireplace into framedenclosure. This allows for 1/2” in front of framing tabs for finishingmaterials.3. Drywall or other material can extend flush with the appliance on thebottom, sides and top of fireplace. (louvered models only)4. When installing horizontal with a 90 degree bend maintain a minimumof two and a half (2.5”) inches above the bend in enclosures,insulationsleeve is required. If greater than six and a half (6.5”) aninsulation sleeve is not required.5. For a fireplace with louvers combustible floor can raise 1” abovethe bottom of the fireplace. For a fireplace with HB47CVCK(Clean view Circulating Kit) floor or hearth can raise 7” abovethe bottom of the fireplace with portions being combustible andnon combustible. See drawing on following page.6. When installing MQHB47SWCC wall surround, the fireplacemust be raised a minimum of 3 1/2” above the finished floor, toaccommodate the wall surround. When installingMQHB47SWCV wall surround the fireplace must be raised 23/4” above the finished floor. The fireplace may be raised higherbut the 60” clearance measured from the bottom of the fireplaceto the ceiling must be maintained at all times. (i.e. For an 8 ft.ceiling the unit can be raised only 36 inches.)It is recommended for Propane Horizontal Installations that the venting should be a minimum of one foot vertical off theflue before the elbow on any horizontal runs of one foot or greater. This allows for cleaner combustion and greatly reducescarboning and cleaning of glass. (Does not apply to Back Flue Models).MQHBZDV47 LouveredMQHBZDV47 WITH HB47CVCK(CLEAN VIEW CIRCULATING KIT)20
MQHBZDV4736 - Framing and Facing RequirementsHBZDV47 WITH HB47CVCK (CLEAN VIEW CIRCULATING KIT)HB47CVCK WITH MQHB47SW SURROUND21
Page 1 and 2: SOLACE/SKYLINEINSTALLER: Leave this
Page 3 and 4: Table of ContentsMobile Home/Manufa
Page 5 and 6: Installation and OperationInstallat
Page 7 and 8: MQHBZDV3636 - Locating your Applian
Page 9 and 10: MQHBZDV3636 - Framing and Facing Re
Page 11 and 12: OverlaysMQHBZDV3636 Parts ListHB36A
Page 13 and 14: MQHBZDV4236/MQRB4236 - Locating you
Page 15 and 16: MQHBZDV4236/MQRB4236 - Framing and
Page 17 and 18: MQHBZDV4236/MQRB4236 - Parts ListFi
Page 19: MQHBZDV4736 - Locating your Applian
Page 23 and 24: Child Safety ScreensMQHBZDV4736 - P
Page 25 and 26: CLEARANCES - MQHB36/42/47/MQRB4236
Page 27 and 28: MQSW Wall Mount Surround Dimensions
Page 29 and 30: Installing MQRB4236 Liner Panels29
Page 31 and 32: Installation of HB Porcelain Liners
Page 33 and 34: Millivolt System, Lighting, & Burne
Page 35: Burner System Removal for MQHB36/42
Page 38 and 39: Glass CleaningIt will be necessary
Page 40 and 41: MQROCK1/MQRSP2 Setup for Models MQH
Page 42 and 43: MQROCK1/MQRSP1 Setup for Models MQH
Page 44 and 45: Accessories for MQRB3328, MQRB3632,
Page 46 and 47: General Vent Installation Informati
Page 48 and 49: Installation Of Side Wall Venting1.
Page 50: LIMITED LIFETIME WARRANTYThis Limit

Kingsman Marquis Solace Manual - Brock White

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?