Universal Small Block Mopar/318/340/360 Carbureted System

More documents

Recommendations

Info

H. Locate the S/C support bracket and one ofthe 1"OD x 1.755" long spacers provided.Loosely attach the support bracket to theS/C bracket by placing the provided 3/8-16x 3.25" bolt and washer through the S/Cbracket, spacer and then attaching the supportbracket. Secure using the 3/8-16 nylocnut and washer provided. (See Fig. 5.1-b,5.1-d.)FACTORYHARDWARE1"OD x1.755"L SPACERALT. STAYADJUSTING BOLTFACTORYALT. STAYSUPPORTBRACKETSUPPORTBRACKETFig. 5-f.625"OD x 1.755"LONG SPACERS/C BRACKETFig. 5-dI Locate te remaining two 1"OD x 1.755"long spacers and the two 1"OD x 1.321"spacers. Secure these by installing the two3/8-16 x 4.5" bolts and washers through theS/C bracket, 1.755" long spacers, supportbracket, 1.321" spacers and into the cylinderhead. (See Figs. 5.1-b, 5.1-e.)FACTORYHARDWARE1"OD x 1.321"SPACERS1"OD x 4.255"SPACERSALTERNATOR1"OD x 4.276"SPACERJFig. 5-eUsing the factory alternator hardware andthe .625"OD x 1.755" long spacer provided,install the alternator as shown. (See Figs.5.1-f, 5.1-g.)Fig. 5-.1-gP/N: 4809658©2006 Paxton AutomotiveAll Rights Reserved, Intl. Copr. Secured23MAR06 v1.0 UnivSBMCarb(4809658v1.0)5-2
K. Attach the alternator stay to the alternatorusing the factory retainer.L. Tighten all hardware installed to this point,making sure that all spacers and brackets areflat against their mounting surfaces. (SeeFig. 5.1-e.)5.2 SUPERCHARGER INSTALLATIONA. Attach the oil drain line to the superchargerand secure using one of the #8 hose clampsprovided.B. Lower the supercharger onto the mountingplate installed on the engine.C. Loosely start the remaining five 3/8" x 1"bolts through the mounting plate and intothe supercharger gear case. Tighten in steps.(See Figs. 5.1-b, 5.2-a.)D. Attach the oil drain line to the fitting previouslyinstalled in the oil pan and secureusing the supplied #8 hose clamp.*** NOTE ***Some applications (depending on intake manifoldheight) may require the reclocking of the superchargervolute. If reclocking is required for your application,loosen and remove the six 1/4-20 cap screwsand retaining plates that hold the compressor housing(volute) to the gearcase. If the compressor housingdoes not rotate freely relative to the gearcase, DONOT FORCE IT. SERIOUS SUPERCHARGER DAMAGEMAY OCCUR. The machined mating surfaces aredesigned to prevent pressurized air from escapingand have minimal tolerances. If the housing will notmove or is very tight, contact Paxton Automotiveimmediately at 888 9-paxton and ask our servicedepartment for further assistance.*** NOTE ***The oil drain hose may need to be trimmed for properfit. It must maintain a continuous downward directionfree of any dips or restrictions.E. Install the 1/8"NPT x -4 x 90° fitting ontothe oil feed fitting using oil to lubricate thethreads. Attach the oil feed hose to this fittingand tighten. (See Fig. 5.2-a.)OIL FEEDCONNECTIONFig. 5-.2-a5-3P/N: 4809658©2006 Paxton AutomotiveAll Rights Reserved, Intl. Copr. Secured23MAR06 v1.0 UnivSBMCarb(4809658v1.0)
Page 1 and 2: S U P E R C H A R G E R SOwner’s
Page 3 and 4: Proper installation of this system
Page 5 and 6: TABLE OF CONTENTSFOREWORD . . . . .
Page 7 and 8: S U P E R C H A R G E R SSmall Bloc
Page 9 and 10: Congratulations! You have purchased
Page 11 and 12: 2.1 PREPARATION/REMOVALA. Disconnec
Page 13 and 14: Section 3OIL FEED INSTALLATION3.1 O
Page 15 and 16: Section 4OIL DRAIN INSTALLATION4.1
Page 17: Section 5MOUNTING BRACKET/SUPERCHAR
Page 21 and 22: Section 6CRANK PULLEY AND SUPERCHAR
Page 23 and 24: Section 7AIR INLET DUCTING INSTALLA
Page 25 and 26: 8.1 CARBURETOR MODIFICATIONSA. If y
Page 27 and 28: Section 9DISCHARGE INSTALLATION (OP
Page 29 and 30: 10.1 FINAL REASSEMBLY AND CHECKSect

Universal Small Block Mopar/318/340/360 Carbureted System

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?